Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.
- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: isolated Ø 4 mm female sockets
- Output protected against voltage surges
Clamp on Tester for multimeters, oscilloscopes and current faults, max. 200 A AC, max. Diameter 20 mm. The Clamp on Tester MN series offers 3 choices for the output. In addition to AC and AC voltage, a DC voltage output is possible from the Clamp on Tester. The test instrument is sent out manufacturer calibrated - a certification according to ISO standards is available optionally.
- Rated current: 200 A AC
- Output signal: AC voltage
- Output/input ratio: 10 mV / A AC
- Output: isolated Ø 4 mm female sockets
Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. diameter 20 mm.
- Rated current: 200 A AC
- Transformation ratio: 1,000/1
- Output: isolated Ø 4 mm female sockets
- Output protected against voltage surges
Current Clamp for multimeters, oscilloscopes and current faults, max. 200 A AC, max. diameter 20 mm.
- Rated current: 200 A AC
- Output signal: AC voltage
- Output/input ratio: 10 mV / A AC
- Output: isolated Ø 4 mm female sockets
The 100N Dynamometer is suited for weighing all goods of up to 10 kg or 22 lbs. The Dynamometer as a high resolution and a maximum deviation of ±0.3 % at full load - unique for this kind of force meter. Due to its type of construction, the Dynamometer doesn't need any batteries and is also suited for demonstration purposes in schools or universities.
- Measuring range: 0 ... 10 kg
- Resolution: 100 g
- Low on maintenance
- Resistance to corrosion
- Additional accessories
The environmental meter is used for fast and accurate detection of pH and temperature. Due to the practical double display, both values can be read simultaneously on the environmental meter.
- Measuring range: 0.0 ... 14.0 pH
- Resolution: 0.01 pH
- Accuracy: ± 0.02 pH
- 100 points Datalogger
- (ATC) in the range 0 ... 80°C / 32 ... 176°F
- Waterproof to IP 67
- Incl. ISO calibration certificate
- Measuring range: 0.0 ... 14.0 pH
- Resolution: 0.01 pH
- Accuracy: ± 0.02 pH
- 100 points Datalogger
- (ATC) in the range 0 ... 80°C / 32 ... 176°F
- Waterproof to IP 67
- Incl. ISO calibration certificate
The 100N Force Gauge is suited for weighing all goods of up to 10 kg or 22 lbs. The Force Gauge as a high resolution and a maximum deviation of ±0.3 % at full load - unique for this kind of force meter. Due to its type of construction, the Force Gauge doesn't need any batteries and is also suited for demonstration purposes in schools or universities.
- Measuring range: 0 ... 10 kg
- Resolution: 100 g
- Low on maintenance
- Resistance to corrosion
- Additional accessories
The 100N Hanging Scale is suited for weighing all goods of up to 10 kg or 22 lbs. The hanging scales have a high resolution and a maximum deviation of ±0.3 % at full load - unique for this kind of force meter. Due to their type of construction, the hanging scales don't need any batteries and are also suited for demonstration purposes in schools or universities.
- Measuring range: 0 ... 10 kg
- Resolution: 100 g
- Low on maintenance
- Resistance to corrosion
- Additional accessories
The 100N Laboratory Balance is suited for weighing all goods of up to 10 kg or 22 lbs. The Laboratory Balance as a high resolution and a maximum deviation of ±0.3 % at full load - unique for this kind of force meter. Due to its type of construction, the Laboratory Balance doesn't need any batteries and is also suited for demonstration purposes in schools or universities.
- Measuring range: 0 ... 10 kg
- Resolution: 100 g
- Low on maintenance
- Resistance to corrosion
- Additional accessories
The waterproof Swimming Pool pH meter is used for fast and accurate measurement of pH and temperature. Due to the practical double display, both values can be read simultaneously on the pH meter. The waterproof and robust housing (IP 67) means the pH meter can be used under difficult conditions.
- Measuring range: 0.0 ... 14.0 pH
- Resolution: 0.01 pH
- Accuracy: ± 0.02 pH
- 100 points Datalogger
- (ATC) in the range 0 ... 80°C / 32 ... 176°F
- Waterproof to IP 67
- Incl. ISO calibration certificate
- Measuring range: 0.0 ... 14.0 pH
- Resolution: 0.01 pH
- Accuracy: ± 0.02 pH
- 100 points Datalogger
- (ATC) in the range 0 ... 80°C / 32 ... 176°F
- Waterproof to IP 67
- Incl. ISO calibration certificate
Clamp Meter to test leakage / RMS measurement / continuity and resistance test. With PCE-LCT 1 leakage current clamp meter it is possible to measure leakage current with a range up to 100 A. The current meter can measure leakage current while current flows through electrical conductors that are not designed for conduction current. The leakage clamp meter is delivered manufacturer calibrated and can additionally be certified to ISO or standards.
- Measures current up to 100 A
- Measures voltage up to 600 V
- Measures resistance up to 400 Ohms
- Test cables are included
Clamp on Tester PCE-LCT 1 to test leakage / RMS measurement / continuity and resistance test. The Clamp on Tester can measure leakage currents which appear when current flows through electrical conductors which are not designed for conduction current. The Clamp on Tester, as all test instruments, is delivered manufacturer calibrated, but can additionally be certified to ISO.
- Measures current up to 100 A
- Measures voltage up to 600 V
- Measures resistance up to 400 O
- Test cables are included
The condition monitoring tachometer can be used contactless or with mechanical contact. The PCE-T237 condition monitoring tachometer is particularly suitable for recording rotational speeds and speeds on rotating machines and systems (on conveyor belts, motors, belt drives, etc.).
- Contact measurement of rpm via cone adapter
- Contact measurement of m / min via surface wheel
- Robust ABS plastic housing
- Meter count: 0.1 ... 199,999 m
The condition monitoring tachometer can be used contactless or with mechanical contact. The PCE-T237 condition monitoring tachometer is particularly suitable for recording rotational speeds and speeds on rotating machines and systems (on conveyor belts, motors, belt drives, etc.).
- Contact measurement of rpm via cone adapter
- Contact measurement of m / min via surface wheel
- Robust ABS plastic housing
- Meter count: 0.1 ... 199,999 m
- Incl. ISO calibration certificate
With the PCE-LCT 1 Current Clamp it is possible to measure leakage currents up to a range of 100 A. PCE-LCT 1 Current Clamp can measure leakage currents which appear when current flows through electrical conductors which are not designed for conduction current.
- Measures current up to 100 A
- Measures voltage up to 600 V
- Measures resistance up to 400 O
- Test cables are included
Digital Multimeter to test leakage / RMS measurement / continuity and resistance test.
- Measures current up to 100 A
- Measures voltage up to 600 V
- Measures resistance up to 400 O
- Test cables are included
