The Xgard-1-H2 is a single-gas Gas Leak Detector used to warn for gases (Hydrogen, H₂, 0 ... 2000 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Hydrogen, H₂, 0 ... 2000 ppm)
- Additional display and alarm station
- ATEX or UL approval

The PCE-PGM 100 gloss meter works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the gloss meter emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.

- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU

 

The Material Hardness Tester for Metal PCE-2600N is used wherever a fast hardness test has to be carried out. It is possible to use the material tester PCE-2600N to determine the surface hardness of many metals. The material tester PCE-2600N is especially suitable for quality or product inspection.

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.8%
- Impactor: DL
- Display: 128 x 64 OLED

The Material Hardness Tester for Metal PCE-2600N is used wherever a fast hardness test has to be carried out. It is possible to use the material tester PCE-2600N to determine the surface hardness of many metals. The material tester PCE-2600N is especially suitable for quality or product inspection.

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.8%
- Impactor: DL
- Display: 128 x 64 OLED

The Metal Hardness Testing Durometer PCE-2600N is used wherever a fast hardness test has to be carried out. It is possible to use the durometer PCE-2600N to determine the surface hardness of many metals. The durometer PCE-2600N is especially suitable for quality or product inspection.

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.8%
- Impactor: DL
- Display: 128 x 64 OLED

The PCE-PGM 100 NDT tester or gloss meter works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the gloss meter emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.

- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU

 

The PCE-PGM 100 gloss meter works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the gloss meter emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.

- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU

 

The Portable Metal Hardness Tester PCE-2600N is used wherever a fast hardness test has to be carried out. It is possible to use the hardness tester PCE-2600N to determine the surface hardness of many metals. The hardness tester PCE-2600N is especially suitable for quality or product inspection.

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.8%
- Impactor: DL
- Display: 128 x 64 OLED

The PCE-PGM 100 Surface Testing works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the Surface Testing emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.

- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU 

 

The Xgard-1-H2 is a single-gas Gas detector used to warn for gases (Hydrogen, H₂, 0 ... 2000 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Hydrogen, H₂, 0 ... 2000 ppm)
- Additional display and alarm station
- ATEX or UL approval

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This gloss meter allows you to measure very high gloss surfaces above 70 gloss units (GU).

- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. These gloss test instruments allow you to measure very high gloss surfaces above 70 gloss units (GU).

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This gloss meter allows you to measure very high gloss surfaces above 70 gloss units (GU).

- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 1000 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

The PCE-SGM 60 surface tester and gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This meter allows you to measure very high gloss surfaces above 70 gloss units (GU).

- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

The Xgard-1-O3 is a single-gas Gas Leak Detector used to warn for gases (Ozone, O₃, 0 ... 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Ozone, O₃, 0 ... 1 ppm)
- Additional display and alarm station
- ATEX or UL approval

- Measuring range: 0 ... 5,000 N / 0 ... 1,124 lbs
- Resolution: 1 N / 0.22 lbs
- Accuracy: ± 0.1% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display
- Incl. ISO calibration certificate

- Measuring range: 0 ... 5,000 N / 0 ... 1,124 lbs
- Resolution: 1 N / 0.22 lbs
- Accuracy: ± 0.1% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display
- Incl. ISO calibration certificate