Order no.: PCE-DFG NF 2K
The force gauge PCE-DFG NF 2K with an external load cell is designed for the measurement of compressive forces at hard-to-reach measuring points. The load cell has several threaded holes on the bottom that allow a firm installation.


- Measuring range: 0 ... 2 kN / 2,000 N / 450 lbs
- Resolution: 0.2 N / 0.04 lbs
- Accuracy: ± 0.5% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display
- Incl. ISO calibration certificate
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DFG NF 5K
The force gauge PCE-DFG NF 5K with an external load cell is designed for the measurement of compressive forces at hard-to-reach measuring points. The load cell has several threaded holes on the bottom that allow a firm installation.


- Measuring range: 0 ... 5 kN / 5,000 N / 1,124 lbs
- Resolution: 0.5 N / 0.1 lbs
- Accuracy: ± 0.5% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display
- Incl. ISO calibration certificate
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-SGM 60-ICA

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This gloss meter allows you to measure very high gloss surfaces above 70 gloss units (GU).


- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-SGM 60-ICA
The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. These gloss test instruments allow you to measure very high gloss surfaces above 70 gloss units (GU).


- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-SGM 60-ICA

The PCE-SGM 60 surface tester and gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This meter allows you to measure very high gloss surfaces above 70 gloss units (GU).


- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: TETRA-MINI

TETRA-MINI alerts the user acoustically, visually and vibrationally to the presence of flammable gases (CH4), oxygen (O2), hydrogen sulfide (H2S) and carbon monoxide (CO). Furthermore, this unpumped four-gas meter displays the current measured value on its graphic LCD screen with backlight. Other gas sensors are available for this instrument. Call for details.


- Sensor types: CH4 / H2S / CO / O2
- Easy one-button operation
- Rechargeable Li-ion battery
- ATEX II 2G EEx iad IIC T4 approved

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: TETRA-MINI

TETRA-MINI alerts the user acoustically, visually and vibrationally to the presence of flammable gases (CH4), oxygen (O2), hydrogen sulfide (H2S) and carbon monoxide (CO). Furthermore, this unpumped four-gas meter displays the current measured value on its graphic LCD screen with backlight. Other gas sensors are available for this instrument. Call for details.


- Sensor types: CH4 / H2S / CO / O2
- Easy one-button operation
- Rechargeable Li-ion battery
- ATEX II 2G EEx iad IIC T4 approved

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: PCE-SW 5000N

PCE-SW 5000N is a portable battery-powered industrial floor scale or pallet scale featuring two heavy-duty parallel weighing beams made of lacquered steel that can be positioned up to 4 m / 13 ft apart. Thus, the adjustable width accommodates multiple pallet, box and container sizes. In addition, the scale's stainless-steel-encased display can be placed up to 4 m / 13 ft away from the weighing beams, allowing for wall mounting.


- Weighing capacity: 5000 kg / 11023 lb (=5.5 T)
- Weighing units: kilograms (kg) or pounds (lbs)
- Resolution: 2 kg
- Accuracy: ± 8 kg
- Bi-directional RS-232 interface

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-SW 5000N

PCE-SW 5000N is a portable battery-powered industrial pallet scale or floor scale featuring two heavy-duty parallel weighing beams made of lacquered steel that can be positioned up to 4 m / 13 ft apart. Thus, the adjustable width accommodates multiple pallet, box and container sizes. In addition, the scale's stainless-steel-encased display can be placed up to 4 m / 13 ft away from the weighing beams, allowing for wall mounting.


- Weighing capacity: 5000 kg / 11023 lb (=5.5 T)
- Weighing units: kilograms (kg) or pounds (lbs)
- Resolution: 2 kg
- Accuracy: ± 8 kg
- Bi-directional RS-232 interface


Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-SW 5000N

PCE-SW 5000N are portable battery-powered industrial pallet beams or floor scales featuring two heavy-duty parallel weighing beams made of lacquered steel that can be positioned up to 4 m / 13 ft apart. Thus, the adjustable width accommodates multiple pallet, box and container sizes. In addition, the scale's stainless-steel-encased display can be placed up to 4 m / 13 ft away from the pallet beams, allowing for wall mounting.


- Weighing capacity: 5000 kg / 11023 lb (=5.5 T)
- Weighing units: kilograms (kg) or pounds (lbs)
- Resolution: 2 kg
- Accuracy: ± 8 kg
- Bi-directional RS-232 interface 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-SW 5000N

PCE-SW 5000N is a portable battery-powered industrial pallet scale or floor scale featuring two heavy-duty parallel weighing beams made of lacquered steel that can be positioned up to 4 m / 13 ft apart. Thus, the adjustable width accommodates multiple pallet, box and container sizes. In addition, the scale's stainless-steel-encased display can be placed up to 4 m / 13 ft away from the weighing beams, allowing for wall mounting.


- Weighing capacity: 5000 kg / 11023 lb (=5.5 T)
- Weighing units: kilograms (kg) or pounds (lbs)
- Resolution: 2 kg
- Accuracy: ± 8 kg
- Bi-directional RS-232 interface 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: Gas-Pro-1

This gas detector Gas-Pro-1 can gauge with its sensors a maximum of four different gases. Because of this versatility, the gas detector Gas-Pro-1 is ideal for use in a variety of applications, such as: near canals, sewage treatment plants, drains, wastewater facilities, dumps/landfills, chemical/oil plants, shipping ports and more.


- Purpose: Personal protection
- Sensor type: CO / H2S / O2 / CH4
- Memory: Yes
- Interface: USB
- Includes suction pump
- Other gas sensors available upon request. (Please email jmu@pce-instruments.com (UK) or jwe@pce-instruments.com (US) for details!)

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: PCE-DFG N 10K
The PCE-DFG N 10K dynamometer measures both tensile and compressive forces with very high resolution. The tensile force and the compressive force are often determined in the laboratory, for example, to determine the yield, the breakaway force, and the force required to push a button or switch. You can buy the dynamometer PCE-DFG N 10K here in our online shop.

- Measuring range: 0 ... 10,000 N / 0 ... 2,248 lbs
- Resolution: 5 N / 1.12 lbs
- Accuracy: ± 0.1% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display
- Incl. ISO calibration certificate
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DFG N 10K
The PCE-DFG N 10K force gauge measures both tensile and compressive forces with very high resolution. The tensile force and the compressive force are often determined in the laboratory, for example, to determine the yield, the breakaway force, and the force required to push a button or switch. You can buy the force gauge PCE-DFG N 10K here in our online shop.

- Measuring range: 0 ... 10,000 N / 0 ... 2,248 lbs
- Resolution: 5 N / 1.12 lbs
- Accuracy: ± 0.1% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display
- Incl. ISO calibration certificate
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GM 100-ICA

The gloss meter is used for measuring on flat surfaces and operates on the principle of a reflectometer. The compact design and the handy size of the gloss meter makes it useful for on-site measurements or during operation of production plant. All test instruments are delivered manufacturer calibrated and can be certified to ISO as an option.


- Measurement angles 20º, 60º and 85º degree angles
- Measurement range: 0.0 to 200 gloss units
- Standards: ISO 2813, GB 9754-88, GB 9966.5
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-IGM 60-ICA

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.


- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GM 100-ICA

The gloss surface tester is used for measuring on flat surfaces and operates on the principle of a reflectometer. The compact design and the handy size of the gloss surface tester makes it useful for on-site measurements or during operation of production plant.


- Measurement angles 20º, 60º and 85º degree angles
- Measurement range: 0.0 to 200 gloss units
- Standards: ISO 2813, GB 9754-88, GB 9966.5 
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-IGM 60-ICA

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.


- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 1000 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-TUM 50
The turbidity meter PCE-TUM 50 is a portable device for measuring turbidity according to ISO 7027. This allows the user to quickly and easily determine important water parameters with the turbidity meter and to check the quality of drinking water and waste water.

- Measurement method: ISO 7027 (90°)
- Measuring ranges: 0 ... 2000 NTU
                                   0 ... 500 EBC
                                   0 ... 9999 ASBC
- 3 measuring units
Turbidity calibration up to 7 points
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-TUM 50
The water analysis meter PCE-TUM 50 is a portable device for measuring turbidity according to ISO 7027. This allows the user to quickly and easily determine important water parameters with the water analysis meter and to check the quality of drinking water and waste water.

- Measurement method: ISO 7027 (90°)
- Measuring ranges: 0 ... 2000 NTU
                                   0 ... 500 EBC
                                   0 ... 9999 ASBC
- 3 measuring units
Turbidity calibration up to 7 points
Manufacturer: PCE Instruments
Test Instruments manufacturer