Industrial Measurement Products and Solutions
Order no.: TXgard-IS+O2

The TXgard-IS+O2 is a single-gas Gas Leak Detector used to warn for gases (Oxygen, O2, 0 ... 25 vol%), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).


- Stationary
- For (Oxygen, O2, 0 ... 25 vol%)
- Additional display and alarm station
- ATEX or UL approval

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: CA-B102

The CA-B102 Clamp on Tester is designed for fast location of insulation faults. The Clamp on Tester has a maximum diameter up to 112 mm (4.4 in), and can be used with multimeters. Two selectable measuring ranges are available to allow for precise measurement according to DIN VDE 010.
- Dual range: 4 A and 400 A AC
- Large jaw diameter: 112 mm / 4.4 in
- For measurement according to DIN VDE 0100

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: CA-B102

The CA-B102 Current Clamp is designed for fast location of insulation faults. The Current Clamp has a maximum diameter up to 112 mm (4.4 in), and can be used with multimeters. Two selectable measuring ranges are available to allow for precise measurement according to DIN VDE 010.
- Dual range: 4 A and 400 A AC
- Large jaw diameter: 112 mm / 4.4 in
- For measurement according to DIN VDE 0100

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: PCE-IR 31

PCE-IR 31 is a non-contact digital infrared thermometer or temperature meter for high-temperature applications. Made of stainless steel and designed for use in harsh industrial conditions, the temperature meter features an IP 65 rating. The device measures infrared radiation and converts it into an analog and switching signal. The switching signal can be used as an opener or closer. In addition, the temperature meter shows the measured value on the built-in LED screen.


- Measuring range: 0 ... 1000°C / 32 ... 1832°F
- M12 thread 5-pin connection
- Quick response time 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-IR 31

PCE-IR 31 is a non-contact digital infrared thermometer or temperature meter for high-temperature applications. Made of stainless steel and designed for use in harsh industrial conditions, the temperature meter features an IP 65 rating. The device measures infrared radiation and converts it into an analog and switching signal. The switching signal can be used as an opener or closer. In addition, the temperature meter shows the measured value on the built-in LED screen.


- Measuring range: 0 ... 1000°C / 32 ... 1832°F
- M12 thread 5-pin connection
- Quick response time


Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CA-B102

The CA-B102 Power Analyzer is designed for fast location of insulation faults. The Power Analyzer has a maximum diameter up to 112 mm (4.4 in), and can be used with multimeters. Two selectable measuring ranges are available to allow for precise measurement according to DIN VDE 010.
- Dual range: 4 A and 400 A AC
- Large jaw diameter: 112 mm / 4.4 in
- For measurement according to DIN VDE 0100

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: PCE-WSM 100
The camera microscope PCE-WMS 100 is the ideal aid for repair and service workshops. Thanks to the movable camera arm, the camera can be precisely aligned by the camera microscope on the object to be optically examined.

- Resolution: 2304 x 1536 pixels
- Magnification: 4.8x ... 220x
- Light source: LED ring light
- Full-HD resolution
- HDMI & USB interface
- SD memory to 64 GB
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DFG N 5K
The dynamometer PCE DFG N 5K measures both tensile and compressive forces with a very high resolution. The tensile force and the compressive force are often determined in the laboratory, for example, to determine the yield, the breakaway force, and the force required to push a button or switch. You can buy the dynamometer PCE-DFG N 5K here in our online shop. 

- Measuring range: 0 ... 5,000 N / 0 ... 1,124 lbs
- Resolution: 1 N / 0.22 lbs
- Accuracy: ± 0.1% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display
- Incl. ISO calibration certificate
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DFG N 5K
The force gauge PCE DFG N 5K measures both tensile and compressive forces with a very high resolution. The tensile force and the compressive force are often determined in the laboratory, for example, to determine the yield, the breakaway force, and the force required to push a button or switch. You can buy the force gauge PCE-DFG N 5K here in our online shop. 

- Measuring range: 0 ... 5,000 N / 0 ... 1,124 lbs
- Resolution: 1 N / 0.22 lbs
- Accuracy: ± 0.1% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display
- Incl. ISO calibration certificate
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: TXgard-IS+O2

The TXgard-IS+O2 is a single-gas Gassensor used to warn for gases (Oxygen, O2, 0 ... 25 vol%), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).


- Stationary
- For (Oxygen, O2, 0 ... 25 vol%)
- Additional display and alarm station
- ATEX or UL approval

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: PCE-WSM 100
The Inspection Camera PCE-WMS 100 is the ideal aid for repair and service workshops. Thanks to the movable camera arm, the camera can be precisely aligned by the inspection camera on the object to be optically examined.

- Resolution: 2304 * 1536 pixels
- Magnification: 4.8x ... 220x
- Light source: LED ring light
- Full-HD resolution
- HDMI & USB interface
- SD memory to 64 GB
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: TXgard-IS+O2

The TXgard-IS+O2 is a single-gas Gassensor used to warn for gases (Oxygen, O2, 0 ... 25 vol%), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).


- Stationary
- For (Oxygen, O2, 0 ... 25 vol%)
- Additional display and alarm station
- ATEX or UL approval

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: PCE-PGM 100

The PCE-PGM 100 gloss meter works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the gloss meter emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.


- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PGM 100

The PCE-PGM 100 NDT tester or gloss meter works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the gloss meter emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.


- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PGM 100

The PCE-PGM 100 Surface Testing works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the Surface Testing emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.


- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: GTI MM-2e

A color viewing box enables the user to make direct color measurements of goods which are planned to be produced or which are being produced already. Therefore, color measurements by means of a color viewing box are crucial for companies that wish to offer products of high and constant quality. This color viewing box supports up to four different light sources, depending on the model.


- Standard illuminant: D65
- Office light: TL84
- House light: A
- Lighting Area: 36 x 46 x 25 cm (L x W x H)

 

Manufacturer: GTI GmbH
Test Instruments manufacturer
Order no.: GTI MM-2e

A color viewing box enables the user to make direct color measurements of goods which are planned to be produced or which are being produced already. Therefore, color measurements by means of a color viewing box are crucial for companies that wish to offer products of high and constant quality. This color viewing box supports up to four different light sources, depending on the model.


- Standard illuminant: D65
- Office light: TL84
- House light: A
- Lighting Area: 36 x 46 x 25 cm (L x W x H)

 

Manufacturer: GTI GmbH
Test Instruments manufacturer
Order no.: ZXCON

ZXCON is a consistometer / viscometer used to measure flow rate, viscosity or consistency by Bostwick method. Designed for conducting quick and accurate Bostwick tests of liquids and pastes for compliance with MIL-R-81294D and ASTM F1080-93, this consistometer features:


- Scale length of 240 mm
- 75 ml sample size acceptance
- Built-in level and leveling feet
- Engraved 0.5 cm graduations
- Durable, stainless steel construction
- Spring-loaded gate that prevents premature flow

 

Manufacturer: ENDECOTTS LIMITED
Test Instruments manufacturer
Order no.: AQ-300 Set EF

The Formaldehyde Meter AQ-300 Set EF is a high-precision measuring device for measuring the formaldehyde concentration in our circulating air. You can buy the Formaldehyde Meter AQ-300 Set EF here in our online shop.


- Range Formaldehyde: 0...10 ppm
- High accuracy and functionality
- Alarm function: "High", "Low", Mute
- Alarm output: Transistor output, 150-mA max
- Low Alarm, High Alarm & Control
- Analog output: 0... 5V
- Location ID: Storage of the measuring location

Manufacturer: AeroQual Limited
Test Instruments manufacturer
Order no.: PCE-428

PCE-428 is a class 2 data logging sound level meter that meets IEC 60651:1979, IEC 60804:2000, IEC 61672-1:2013, ANSI S1.4-1983 and ANSI S1.43-1997 requirements. This portable high-accuracy sound level meter has a large easy-to-read illuminated LCD screen that displays the sound pressure level (SPL) numerically and graphically in real time. The sound level meter calculates the equivalent continuous sound level Leq (LXeq).

- Measuring range: 25 ... 136 db(A)
- LXY (SPL), Leq (LXeq), LXYSD, LXSEL, LXE, LXYmax, LXYmin, LXPeak, LXN
- Frequency weighting: A, B, C and Z
- Time weighting: Fast (125 ms), slow (1 sec) and impulse (35 ms), decay (1500 ms)
- adjustable data-recording interval from 1 s ... 24 h
- 1/1 octave band filter (optional 1/3 octave band filter upgrade)
- Includes factory calibration certificate according to ISO 9001

Manufacturer: PCE Instruments
Test Instruments manufacturer