The PCE-SGM 60 surface tester and gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This meter allows you to measure very high gloss surfaces above 70 gloss units (GU).

- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm

 

The Xgard-1-CL2 is a single-gas Gas detector used to warn for gases (Chlorine, CL₂, 0 ... 5 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Chlorine, CL₂, 0 ... 5 ppm)
- Additional display and alarm station
- ATEX or UL approval

 

The Material Surface Roughness Tester PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.02 to 100um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)

The Roughness Tester PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)

The Surface Profilometer PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)

The Surface Testing Roughness Tester PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)

The PCE-DDM 3WI-ICA Crane Scale is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 3WI-ICA Crane Scale is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 3,000 kg / 30 kN / 6,614 lbs
- Resolution: 1 kg / 10 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied without remote control / indicator
- incl. ISO Calibration Certificate

The PCE-DDM 3WI-ICA Hanging Scale is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 3WI-ICA Hanging Scale is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 3,000 kg / 30 kN / 6,614 lbs
- Resolution: 1 kg / 10 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied without remote control / indicator
- incl. ISO Calibration Certificate

The PCE-DDM 3WI-ICA Weighing Hook is the ideal tool for weighing big loads and for measuring strong tensile forces. The PCE-DDM 3WI-ICA Weighing Hook is delivered in a protective carrying case and includes two shackles made of heavy-duty aluminum. The instrument is manufacturer calibrated, but can be certified to ISO standards for an additional fee.

- Measurement range: 3,000 kg / 30 kN / 6,614 lbs
- Resolution: 1 kg / 10 N
- Units of measurement: kg / t / lbs / N / kN
- Supplied without remote control / indicator
- incl. ISO Calibration Certificate

This clamp meter is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The clamp meter is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

This clamp on tester is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The clamp on tester is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

This current clamp is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The current clamp is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

This HVAC meter is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The HVAC meter is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

This 1-Phase-Power Meter is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyzer clamp is equipped with data logger. The test instrument is delivered manufacturer ISO calibrated.

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Records up to 50,000 records
- incl. ISO Calibration Certificate

This power analyzer is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyzer clamp is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

This power datalogger is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyzer clamp is equipped with data logger. The test instrument is delivered manufacturer ISO calibrated.

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

This three-phase digital multimeter is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The three-phase digital multimeter is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

This three-phase electrical tester is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The three-phase electrical tester is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

The PCE-MA 202 is an oven-drying absolute moisture meter for weighing and heating material samples to determine moisture content. The heating chamber warms up to 199 °C / 390 °F with the use of halogen lamps. Drying of the sample to be weighed takes place within the chamber of the absolute moisture meter and the moisture content is subsequently calculated from the difference between the initial and final weight.

- Testing or weighing capacity: 200 g / 7.05 oz
- Readability: 10 mg / 0.01 g / 0.1%
- Adjustable drying temperature and time

PCE-PCO 1 is a handheld particle-counting air quality meter or dust measuring device for measuring the concentration of particles in the air. The PCE-PCO 1 hygienic dust measuring device:

- Measures 6 sizes of particles: 0.3 µm, 0.5 µm, 1.0 µm, 2.5 µm, 5.0 µm, 10 µm
- Offers a robust, 80 MB internal memory
- Features a large, full-color LCD display with backlight
- Includes a built-in camera for image and video recording
- Contains sensors for measuring air temperature, dew point and relative
  humidity
- Displays temperature in degrees Celsius (°C) or Fahrenheit (°F)