Industrial Measurement Products and Solutions
Order no.: PCE-CIC 11

The PCE-CIC 11 Color Matching Cabinet is a simulation instrument, which is mainly used in quality control. The Color Matching Cabinet accurately  corrects light types and thus enables the direct comparison of products which must have special color characteristics.


- Simulation of different light types
- Hour counter for each light type
- Short warm-up time
- According to ASTM D1729, ISO3664, DIN, ANSI, BSI

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-CIC 11

The PCE-CIC 11 color viewing box is a simulation instrument, which is mainly used in quality control. The color viewing box accurately  corrects light types and thus enables the direct comparison of products which must have special color characteristics.


- Simulation of different light types
- Hour counter for each light type
- Short warm-up time
- According to ASTM D1729, ISO3664, DIN, ANSI, BSI

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-IVE 300

PCE-IVE 300 is an industrial endoscope or borescope inspection camera that comes with a rigid telescoping pole that extends up to 1 m (3.28') in length. Ideal for inspecting gutters, chimneys and structures as well as for inspecting parts and under vehicles, the endoscope camera captures both picture and video and saves the files to an SD card memory (included).

 

- Telescopic pole extends up to 1 m (3.28')
- Gooseneck camera head diameter of 28 mm (1.11")
- Waterproof and dustproof IP68 ingress protection rating

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-IVE 300

PCE-IVE 300 is an industrial borescope inspection camera that comes with a rigid telescoping pole that extends up to 1 m (3.28 ft) in length. Ideal for inspecting gutters, chimneys and structures as well as for inspecting parts and under vehicles, the borescope camera captures both picture and video and saves the files to an SD card memory (included).

 

- Telescopic pole extends up to 1 m / 3.3 ft
- Gooseneck camera head diameter of 28 mm / 1.11 in
- Waterproof and dustproof IP68 ingress protection rating

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-IVE 300

PCE-IVE 300 is a borescope inspection camera that comes with a rigid telescoping pole that extends up to 1 m (3.28') in length. Ideal for inspecting gutters, chimneys and structures as well as for inspecting parts and under vehicles, the borescope camera captures both picture and video and saves the files to an SD card memory (included).

- Telescopic pole extends up to 1 m / 3.3 ft
- Gooseneck camera head diameter of 28 mm / 1.11 in
- Waterproof and dustproof IP68 ingress protection rating

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-IVE 300

PCE-IVE 300 is a videoscope or video borescope inspection camera that comes with a rigid telescoping pole that extends up to 1 m (3.28') in length. Ideal for inspecting gutters, chimneys and structures as well as for inspecting parts and under vehicles, the borescope camera captures both picture and video and saves the files to an SD card memory (included).

 

- Telescopic pole extends up to 1 m / 3.3 ft
- Gooseneck camera head diameter of 28 mm / 1.11 in
- Waterproof and dustproof IP68 ingress protection rating

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: Xgard-1-CL2

The Xgard-1-CL2 is a single-gas Gas Leak Detector used to warn for gases (Chlorine, CL2, 0 ... 5 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Chlorine, CL2, 0 ... 5 ppm)
- Additional display and alarm station
- ATEX or UL approval

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: PCE-C-R1S 100t

Due to its ball bearing, the load cell has a special resistance against lateral forces. The load cell has a strong output signal of approx. 4 mV / V and works with a measurement uncertainty of 0.03% F.S.. The load cell is used especially in harsh environments such as truck scales, train scales, machine weighing, etc..

- Rated load / force F.S.: 100 t / 1 MN
- Corrosion resistant IP67
- Bearing surface ball bearing
- 700 Ohm

 

- Other force sensor nominal loads available - see variants!

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: AQ-200 Set OZU

Gas Detector AQ-200 is a highly accurate instrument for measuring ozone concentrations in the air. The Gas Detector can be equipped with four different heads that vary in their measurement range.


- High accuracy and functionality
- Interchangeable sensor heads!
- Battery operation
- Sensor head OZU included in delivery (Ozone 0-0.15 ppm)

 

Manufacturer: Aeroqual
Test Instruments manufacturer
Order no.: PCE-SGM 60

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This gloss meter allows you to measure very high gloss surfaces above 70 gloss units (GU).


- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-SGM 60
The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. These gloss test instruments allow you to measure very high gloss surfaces above 70 gloss units (GU).


- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: AQ-200 Set OZU

Ozone Meter AQ-200 is a highly accurate instrument for measuring ozone concentrations in the air. The Ozone Meter can be equipped with four different heads that vary in their measurement range.


- High accuracy and functionality
- Interchangeable sensor heads!
- Battery operation
- Sensor head OZU included in delivery (Ozone 0-0.15 ppm)

 

Manufacturer: Aeroqual
Test Instruments manufacturer
Order no.: PCE-SGM 60

The PCE-SGM 60 surface tester and gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This meter allows you to measure very high gloss surfaces above 70 gloss units (GU).


- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: Xgard-1-Cl2

The Xgard-1-CL2 is a single-gas Gas detector used to warn for gases (Chlorine, CL2, 0 ... 5 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).


- Stationary
- For (Chlorine, CL2, 0 ... 5 ppm)
- Additional display and alarm station
- ATEX or UL approval

 

Manufacturer: Crowcon Detection Instruments Ltd.
Test Instruments manufacturer
Order no.: PCE-RT 10

The Material Surface Roughness Tester PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.


- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.02 to 100um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RT 10

The Roughness Tester PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.


- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RT 10

The Surface Profilometer PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.


- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RT 10

The Surface Testing Roughness Tester PCE-RT 10 is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.


- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GPA 62-ICA

This clamp meter is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The clamp meter is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-GPA 62-ICA

This clamp on tester is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The clamp on tester is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Datalogger for 50,000 readings / software/ USB interface 
- incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
Test Instruments manufacturer