Industrial Measurement Products and Solutions
Order no.: ABBE-REF 1

ABBE-REF 1 is a high-precision Abbe refractometer for the accurate measurement of refractive indexes (nD), sucrose or sugar contents (% Brix) and mean dispersion values (nF-nC) of transparent and translucent liquids and substances. This bench-top Abbe refractometer can be used to determine refractive indexes in a temperature range from 0 ... +70 ºC (temperature control included).


Measurement ranges:
  1.300 ... 1.700 nD / 0.0 ... 95 % Brix
- Scale division: 0.0005 nD / 0.25 % Brix
- Resolution and accuracy: 0.0002 nD / 0.1 % Brix

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RGB2

PCE-RGB2 is a color meter for RGB (red, green, blue) or HSL (hue, saturation, luminance) color measurements. The colorimeter's 45 ° / 0 ° measurement geometry and 16 mm / ≈ 0.63" diameter aperture accommodate standardized color measurement methods on a variety of surfaces. The handheld color-measuring probe is connected to the colorimeter via a 1.5 m / 4.9' long cable, allowing a wide range of motion for the color measurement procedure.


- Measurement geometry: 45° / 0°
- Measurement range: RGB: 0 to 1023 / HSL: 0 to 1.00
- Resolution: 1 for RGB / 0.001 for HS
- Repeatability: < 3 RGB, for a minimum of 1 measurement
- Internal light source can be disabled to measure active light sources 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RGB2

PCE-RGB2 is a colorimeter for RGB (red, green, blue) or HSL (hue, saturation, luminance) color measurements. The color meter's 45 ° / 0 ° measurement geometry and 16 mm / ≈ 0.63" diameter aperture accommodate standardized color measurement methods on a variety of surfaces. The handheld color-measuring probe is connected to the colorimeter via a 1.5 m / 4.9' long cable, allowing a wide range of motion for the color measurement procedure.


- Measurement geometry: 45° / 0°
- Measurement range: RGB: 0 to 1023 / HSL: 0 to 1.00
- Resolution: 1 for RGB / 0.001 for HS
- Repeatability: < 3 RGB, for a minimum of 1 measurement
- Internal light source can be disabled to measure active light sources 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT-75

The PCE-HT-75 Concrete Hardness Tester is easy to use and is fundamentally used in the construction industry as well as other industrial sectors (testing for Wickel hardness of rolls in commodities). This Hardness Tester in the form of a hammer device for testing concrete is based on the Swiss principle of measurement.


- Spring stretch: 75 ± 0.3 mm / 3 ± .01 in
- Measuring range: 10 ... 70 N/mm²
- Energy: 0.735 J / 0.54 ft-lbs 
- Low strength concrete testing or Type L
- Indication of measurement: 0 to 100 (without dimensions)
- Maximum thickness of concrete (of the material): 70 cm

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT 224E
The Concrete Test Hammer is a measuring tool for testing the strength of concrete. The Concrete Test Hammer measures strength according to the Schmidt principle. According to this measurement method, the quality of concrete can be measured with the Concrete Test Hammer.  The Concrete Test Hammer is also suitable for measuring hardness of rolled paper.  The Concrete Test Hammer displays measurements Rebound Value and can display force in PSI (lbs / in²), MPa, kgF/cm², or N/mm².

- Measuring range: 10 ... 60 N/mm² / 1500 ... 8500 PSI (lbs / in²)
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Digital Display of results
- USB interface for connection to a PC
Data storage
- Rechargeable battery
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT-75

The PCE-HT-75 durometer for concrete is easy to use and is fundamentally used in the construction industry as well as other industrial sectors (testing for Wickel hardness of rolls in commodities). This durometer in the form of a hammer device for testing concrete is based on the Swiss principle of measurement.


- Spring stretch: 75 ± 0.3 mm / 3 ± .01 in
- Measuring range: 10 ... 70 N/mm²
- Energy: 0.735 J / 0.54 ft-lbs
- Low strength concrete testing or Type L
- Indication of measurement: 0 to 100 (without dimensions)
- Maximum thickness of concrete (of the material): 70 cm

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT 224E
The Hardness Tester is a measuring tool for testing the strength of concrete. The Hardness Tester measures strength according to the Schmidt principle. According to this measurement method, the quality of concrete can be measured with the Hardness Tester.  The Hardness Tester is also suitable for measuring hardness of rolled paper.  The Hardness Tester displays measurements Rebound Value and can display force in PSI, MPa, kgF/cm², or N/mm².

- Measuring range: 10 ... 60 N/mm² / 1500 ... 8500 PSI (lbs / in²)
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Digital Display of results
- USB interface for connection to a PC
Data storage
- Rechargeable battery
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MSR 450
The magnetic stirrer PCE-MSR 450 is a stirring instrument for up to 20 liters. The speed of the magnetic stirrer can be adjusted. It is possible to set speeds between 200 and 2200 revolutions per minute. 

- Motor: brushless DC motor (BLDC)
- Number of stirring points: 1
- Maximum stirring volume: 20 l
- Speed range: 200 ... 2200 rpm (adjustable)
- Accuracy: +/- 1 rpm
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT 224E
The Material Tester is a measuring tool for testing the strength of concrete. The Material Tester measures strength according to the Schmidt principle. According to this measurement method, the quality of concrete can be measured with the Material Tester.  The Material Tester is also suitable for measuring hardness of rolled paper.  The Material Tester displays measurements Rebound Value and can display force in PSI, MPa, kgF/cm², or N/mm².

- Measuring range: 10 ... 60 N/mm² / 1500 ... 8500 PSI (lbs / in²)
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Digital Display of results
- USB interface for connection to a PC
Data storage
- Rechargeable battery
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT 224E
The NDT Tester is a measuring tool for testing the strength of concrete. The NDT Tester measures strength according to the Schmidt principle. According to this measurement method, the quality of concrete can be measured with the NDT Tester.  The NDT Tester is also suitable for measuring hardness of rolled paper.  The NDT Tester displays measurements Rebound Value and can display force in PSI, MPa, kgF/cm², or N/mm².

- Measuring range: 10 ... 60 N/mm² / 1500 ... 8500 PSI (lbs / in²)
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Digital Display of results
- USB interface for connection to a PC
Data storage
- Rechargeable battery
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT 224E
The Roll Hardness Tester is a measuring tool for testing the strength of concrete. The Roll Hardness Tester measures strength according to the Schmidt principle. According to this measurement method, the quality of rolled paper can be measured with the Hardness Tester.  The Hardness Tester is also suitable for measuring hardness of concrete.  The Hardness Tester displays measurements Rebound Value and can display force in PSI, MPa, kgF/cm², or N/mm².

- Measuring range: 10 ... 60 N/mm² / 1500 ... 8500 PSI (lbs / in²)
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Digital Display of results
- USB interface for connection to a PC
Data storage
- Rechargeable battery
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT 224E
The Surface Tester is a measuring tool for testing the strength of concrete. The Surface Tester measures strength according to the Schmidt principle. According to this measurement method, the quality of concrete can be measured with the Surface Tester.  The Surface Tester is also suitable for measuring hardness of rolled paper.  The Surface Tester displays measurements Rebound Value and can display force in PSI, MPa, kgF/cm², or N/mm².

- Measuring range: 10 ... 60 N/mm² / 1500 ... 8500 PSI (lbs / in²)
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Digital Display of results
- USB interface for connection to a PC
Data storage
- Rechargeable battery
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RGB2

PCE-RGB2 is a colorimeter for RGB (red, green, blue) or HSL (hue, saturation, luminance) color measurements. The color meter's 45 ° / 0 ° measurement geometry and 16 mm / ≈ 0.63" diameter aperture accommodate standardized color measurement methods on a variety of surfaces. The handheld color-measuring probe is connected to the colorimeter via a 1.5 m / 4.9' long cable, allowing a wide range of motion for the color measurement procedure.


- Measurement geometry: 45° / 0°
- Measurement range: RGB: 0 to 1023 / HSL: 0 to 1.00
- Resolution: 1 for RGB / 0.001 for HS
- Repeatability: < 3 RGB, for a minimum of 1 measurement
- Internal light source can be disabled to measure active light sources 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT-75

The PCE-HT-75 Surface Testing Hammer for concrete is easy to use and is fundamentally used in the construction industry as well as other industrial sectors (testing for Wickel hardness of rolls in commodities). This Surface Testing Hammer in the form of a hammer device for testing concrete is based on the Swiss principle of measurement.


- Spring stretch: 75 ± 0.3 mm / 3 ± .01 in
- Measuring range: 10 ... 70 N/mm²
- Energy: 0.735 J / 0.54 ft-lbs
- Low strength concrete testing or Type L
- Indication of measurement: 0 to 100 (without dimensions)
- Maximum thickness of concrete (of the material): 70 cm

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: ABBE-REF 1

ABBE-REF 1 is a high-precision Abbe refractometer for the accurate measurement of refractive indexes (nD), sucrose or sugar contents (% Brix) and mean dispersion values (nF-nC) of transparent and translucent liquids and substances. This bench-top Abbe refractometer can be used to determine refractive indexes in a temperature range from 0 ... +70 ºC (temperature control included).


- Measurement ranges: 1.300 ... 1.700 nD / 0.0 ... 95 % Brix
- Scale division: 0.0005 nD / 0.25 % Brix
- Resolution and accuracy: 0.0002 nD / 0.1 % Brix

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: 5020-1800

The infrared thermometer Hi Temp 1800 measures surface temperatures over a wide temperature range. Additional notable benefits of the infrared thermometer are its very short reaction time (< 1 sec.) and the non-contact IR technology. This infrared thermometer (as all the test instruments) is delivered manufacturer calibrated and can additionally be certified to ISO.


- Measuring range: 100 ... 1800°C / 212 ... 3272°F
- Spectral range: 2.3 - 5 µm
- Resolution:  0.1°C / 0.18°F (<1000°C / 1832°F), 1°C / 1.8°F (1000°C)
- Accuracy: ± 2% or 2°C / 3.6°F, whichever is larger

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: 5020-1800
The Temperature Meter Hi Temp 1800 measures surface temperatures over a wide temperature range. Additional notable benefits of the Temperature Meter are its very short reaction time (< 1 sec.) and the non-contact IR technology. This Temperature Meter (as all the test instruments) is delivered manufacturer calibrated and can additionally be certified to ISO.

 


- Measuring range: 100 ... 1800°C / 212 ... 3272°F
- Spectral range: 2.3 - 5 µm
- Resolution:  0.1°C / 0.18°F (<1000°C / 1832°F), 1°C / 1.8°F (1000°C)
- Accuracy: ± 2% or 2°C / 3.6°F, whichever is larger

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-AQD 20
The CO2 analyzer PCE-AQD 20 is an ideal measuring device for monitoring the air quality at workplaces. The PCE-AQD 20 health and CO2 analyzer is ideal for continuous logging of air temperature, humidity, CO2, PM2.5 and air pressure.

Measuring function
- PM2.5
- Humidity
- Temperature
- CO2
- Air pressure
- Memory: SD card max. 32 GB
- Ideal for workplace monitoring
- Alarm function
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-AQD 20
The CO2 data logger / room climate data logger PCE-AQD 20 is an ideal measuring device for monitoring the air quality at workplaces. The health and CO2 data logger is ideal for continuous logging of air temperature, humidity, CO2, PM2.5 and air pressure.

Measuring function
- PM2.5
- Humidity
- Temperature
- CO2
- Air pressure
- Memory: SD card max. 32 GB
- Ideal for workplace monitoring
- Alarm function
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-AQD 20
The CO2 meter PCE-AQD 20 is an ideal measuring device for monitoring the air quality at workplaces. The PCE-AQD 20 health and CO2 meter is ideal for continuous logging of air temperature, humidity, CO2, PM2.5 and air pressure.

Measuring function
- PM2.5
- Humidity
- Temperature
- CO2
- Air pressure
- Memory: SD card max. 32 GB
- Ideal for workplace monitoring
- Alarm function
Manufacturer: PCE Instruments
Test Instruments manufacturer