Industrial Measurement Products and Solutions
Order no.: PCE-MWM 200

The moisture sensor is a sensor for measuring moisture of sand consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our moisture sensor is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, fuels (CWF).


- Readability mass fraction of water: 0 ... 100%
- Moisture measurement range: ± 0.1 ... 100% (water mass fraction))
- Maximum permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +80 °C

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 240-A

Designed specifically for use in humidity measurement of bulk materials, this moisture sensor is installed in bins, silos, troughs, bunkers case, distributors, augers and conveyors. Material in bulk or flowing mass, such as fibrous materials, gravel, sawdust, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, seed, pastes, ... is continuously measurable.

- Stainless sensor rod (250 mm length)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C  (+41 ... +176 °F)
- Analog and digital signal output

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 240-A

Designed specifically for use real-time measurement of percent moisture measurement of bulk materials. Material in flowing mass, such as granular materials, sand, sawdust, fly ash (mineral), wood chips (surface to 5 cm), grain, powders, seed, and pastes is continuously measurable. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. 

 - Stainless sensor rod (250 mm length)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C  (+41 ... +176 °F)
- Analog and digital signal output

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 240-A

Designed specifically for use in humidity measurement of bulk materials, this humidity sensor is installed in bins, silos, troughs, bunkers case, distributors, augers and conveyors. Material in bulk or flowing mass, such as fibrous materials, gravel, sawdust, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, seed, pastes, ... is continuously measurable.

 - Stainless sensor rod (250 mm length)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C  (+41 ... +176 °F)
- Analog and digital signal output
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 200

The moisture meter is a sensor for measuring moisture of sand consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our moisture meter is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, fuels (CWF).


- Readability mass fraction of water: 0 ... 100%
- Moisture measurement range: ± 0.1 ... 100% (water mass fraction)
- Maximum permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +80 °C

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 200

The moisture sensor is a sensor for measuring moisture of sand consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our moisture sensor is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, fuels (CWF).


- Readability mass fraction of water: 0 ... 100%
- Moisture measurement range: ± 0.1 ... 100% (water mass fraction))
- Maximum permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +76 °C

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 240-A

Designed specifically for use in humidity measurement of bulk materials, this moisture sensor is installed in bins, silos, troughs, bunkers case, distributors, augers and conveyors. Material in bulk or flowing mass, such as fibrous materials, gravel, sawdust, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, seed, pastes, ... is continuously measurable.

 - Stainless sensor rod (250 mm length)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C  (+41 ... +176 °F)
- Analog and digital signal output
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 200

The moisture analyzer is a sensor for measuring moisture of sand and liquids consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our moisture analyzer is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, and fuels (CWF).

- Readability mass fraction of water: 0 ... 100 %
- Moisture measurement range: 0.1 ... 100 % 
  water content in sand and liquids (water mass fraction)
- Max. permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +80 °C

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 240-A

Designed specifically for use in moisture measurement of various bulk materials, these moisture analyzing test instruments are installed in bins, silos, troughs, bunkers, distributors, augers, and conveyors. Material in bulk or flowing mass, such as fibrous materials, gravel, sawdust, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, seed, pastes, ... is continuously measurable.

 - Stainless sensor rod (250 mm length)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C  (+41 ... +176 °F)
- Analog and digital signal output
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 200

The moisture analyzer is a sensor for measuring moisture of sand and liquids consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our moisture analyzer is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, and fuels (CWF).


- Readability mass fraction of water: 0 ... 100%
- Moisture measurement range: ± 0.1 ... 10% (water mass fraction))
- Maximum permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +80 °C

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 300P

For industrial continuous production of wood pellets, chips, sawdust and similar materials when on-line moisture measurement for monitoring and controlling the drying and mixing process is important. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. The PCE-MWM 300P moisture test sensor of PCE Instruments helps meet those criteria through highly accurate moisture measurement.


- Measuring range: 0 ... 100%
- The maximum permissible error (absolute): Lab analysis of your sample determines % error
- Temperature range: -40 ... +150 °C  (-40 ... +302 °F)
- Current consumption: 200 mA
- Power supply : 24 (18 ... 36) VDC
- Questionnaire starts evaluation process
- Application: pellets, wood chips

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 300P

For industrial continuous production of wood pellets, chips, sawdust and similar materials when on-line moisture measurement for monitoring and controlling the drying and mixing process is important. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. The PCE-MWM 300P moisture test sensor of PCE Instruments helps meet those criteria through highly accurate moisture measurement.


- Measuring range: 0 ... 100%
- The maximum permissible error (absolute): Lab analysis of your sample determines % error
- Temperature range: -40 ... +150 °C  (-40 ... +302 °F)
- Current consumption: 200 mA
- Power supply : 24 (18 ... 36) VDC
- Questionnaire starts evaluation process
- Application: pellets, wood chips

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 300P

For industrial continuous production of wood pellets, chips, sawdust and similar materials when on-line moisture measurement for monitoring and controlling the drying and mixing process is important. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. The PCE-MWM 300P moisture test sensor of PCE Instruments helps meet those criteria through highly accurate moisture measurement.


- Measuring range: 0 ... 100%
- The maximum permissible error (absolute): Lab analysis of your sample determines % error
- Temperature range: -40 ... +150 °C  (-40 ... +302 °F)
- Current consumption: 200 mA
- Power supply : 24 (18 ... 36) VDC
- Questionnaire starts evaluation process
- Application: pellets, wood chips

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 300P

For industrial continuous production of wood pellets, chips, sawdust and similar materials when on-line moisture measurement for monitoring and controlling the drying and mixing process is important. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. The PCE-MWM 300P moisture test sensor of PCE Instruments helps meet those criteria through highly accurate moisture measurement.


- Measuring range: 0 ... 100%
- The maximum permissible error (absolute): Lab analysis of your sample determines % error
- Temperature range: -40 ... +150 °C  (-40 ... +302 °F)
- Current consumption: 200 mA
- Power supply : 24 (18 ... 36) VDC
- Questionnaire starts evaluation process
- Application: pellets, wood chips

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-MWM 300P

For industrial continuous production of wood pellets, chips, sawdust and similar materials when on-line moisture measurement for monitoring and controlling the drying and mixing process is important. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. The PCE-MWM 300P moisture test sensor of PCE Instruments helps meet those criteria through highly accurate moisture measurement.


- Measuring range: 0 ... 100%
- The maximum permissible error (absolute): Lab analysis of your sample determines % error
- Temperature range: -40 ... +150 °C  (-40 ... +302 °F)
- Current consumption: 200 mA
- Power supply : 24 (18 ... 36) VDC
- Questionnaire starts evaluation process
- Application: pellets, wood chips

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-USC 20

PCE-USC 20 is a portable or benchtop condition monitoring ultrasonic tester or ultrasonic thickness gauge with a 5.7" TFT color LCD screen. This ultrasound-based thickness meter uses one or two contact transducers (four different probes included; 90 °, 70 °, 60 °, 45 °) to measure material or wall thickness, detect flaws or defects in welds, and monitor the effects of corrosion on pipes and tanks.


- Measurement range: 0.5 ... 9999 mm (steel; longitudinal wave)
- Operating frequency range: 0.5 ... 20 MHz
- Sound velocity: 1000 ... 15000 m/s (continuously adjustable)
- AVG and DAC evaluation methods, display and probes delay, damping and
  reinforcing functions, export and reporting functions 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-USC 20

PCE-USC 20 is a portable or benchtop ultrasonic defectoscope or ultrasonic thickness gauge with a 5.7" TFT color LCD screen. This ultrasound-based defectoscope uses one or two contact transducers (four different probes included; 90 °, 70 °, 60 °, 45 °) to measure material or wall thickness, detect flaws or defects in welds, and monitor the effects of corrosion on pipes and tanks.


- Measurement range: 0.5 ... 9999 mm (steel; longitudinal wave)
- Operating frequency range: 0.5 ... 20 MHz
- Sound velocity: 1000 ... 15000 m/s (continuously adjustable)
- AVG and DAC evaluation methods, display and probes delay, damping and
  reinforcing
  functions, export and reporting functions 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-USC 20

PCE-USC 20 is a portable or benchtop ultrasonic tester or ultrasonic flaw detector with a 5.7" TFT color LCD screen. This ultrasound-based flaw detector uses one or two contact transducers (four different probes included; 90 °, 70 °, 60 °, 45 °) to measure material or wall thickness, detect flaws or defects in welds, and monitor the effects of corrosion on pipes and tanks.


- Measurement range: 0.5 ... 9999 mm (steel; longitudinal wave)
- Operating frequency range: 0.5 ... 20 MHz
- Sound velocity: 1000 ... 15000 m/s (continuously adjustable)
- AVG and DAC evaluation methods, display and probes delay, damping and
  reinforcing functions, export and reporting functions 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-USC 20

PCE-USC 20 is a portable or benchtop ultrasonic tester or ultrasonic thickness gauge with a 5.7" TFT color LCD screen. This ultrasound-based thickness meter uses one or two contact transducers (four different probes included; 90 °, 70 °, 60 °, 45 °) to measure material or wall thickness, detect flaws or defects in welds, and monitor the effects of corrosion on pipes and tanks.


- Measurement range: 0.5 ... 9999 mm (steel; longitudinal wave)
- Operating frequency range: 0.5 ... 20 MHz
- Sound velocity: 1000 ... 15000 m/s (continuously adjustable)
- AVG and DAC evaluation methods, display and probes delay, damping and
  reinforcing functions, export and reporting functions 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-USC 20

PCE-USC 20 is a portable or benchtop ultrasonic tester or ultrasonic thickness gauge with a 5.7" TFT color LCD screen. This ultrasound-based thickness meter uses one or two contact transducers (four different probes included; 90 °, 70 °, 60 °, 45 °) to measure material or wall thickness, detect flaws or defects in welds, and monitor the effects of corrosion on pipes and tanks.


- Measurement range: 0.5 ... 9999 mm (steel; longitudinal wave)
- Operating frequency range: 0.5 ... 20 MHz
- Sound velocity: 1000 ... 15000 m/s (continuously adjustable)
- AVG and DAC evaluation methods, display and probes delay, damping and
  reinforcing functions, export and reporting functions 

 

Manufacturer: PCE Instruments
Test Instruments manufacturer