Order no.: PCE-DMM 50

The pressure sensor PCE-DMM 50 is suitable for stationary and mobile pressure measurement. The pressure sensor PCE-DMM 50 is used in mechanical and plant engineering, laboratory technology and environmental technology. This pressure sensor is battery powered. The measuring range of the pressure sensor reaches up to 600 bar.


- Max. 600 bar / 8702 psi
- Rotating display
- For hygienic applications
- Media: water, oxygen, fuels and oils
- Print: absolute or relative (user selectable)
- Diaphragm: Ceramics
- Accuracy class: 0.2

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-DMM 51

The pressure sensor PCE-DMM 51 is suitable for flush mounting hygiene. Thus, the sensor can be installed both in the food industry as well as in medical technology. The pressure gauge shows on its rotatable display pressures up to 400 bar, relative or absolute. The operating fluid of the pressure sensor has a food safe FDA approval.


- Max. 400 bar / 5801 psi
- Rotating display
- For hygienic applications
- Media: water, paints and coatings, gases, viscous and paste media
- Pressure: relative
- Diaphragm: stainless steel flush
- Accuracy class: 0.2

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VDL 24I
For this shock data logger PCE-VDL 24I the acceleration sensor is delivered with a sampling rate of 1600 Hz. The sensor measures the acceleration, which is currently acting on it (3 axes), for example shock / vibration. The measurements take place at predetermined (selectable) time intervals.

- 3-Axis acceleration up to 1600 Hz and ±16 g
- 32 GB SD memory card
- Evaluation software
- Small design: 86.8 x 44.1 x 22.2 mm / 3.4 x 1.7 x 0.87 in
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-322ALEQ
The sound level meter / noise level meter PCE-322ALEQ is particularly suitable for measuring noise in the field of industrial, health, safety and environmental monitoring. The PCE-322ALEQ sound level meter / noise level meter has a logger function, which allows storage of up to 32700 readings.


- Automatic range: 30 ... 130 dB
- Manual range: 30 ... 80 / 50 ... 100 / 80 ... 130 dB
- Resolution: 0.1 dB
- Accuracy: ±1.4 dB
- Memory capacity: 32700 values
- incl. software for LEQ calculation

Important! The LEQ value is only calculated by the software after the data transfer from the device to the PC or laptop.

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-322ALEQ
The SPL meter PCE-322ALEQ is particularly suitable for measuring noise in the field of industrial, health, safety and environmental monitoring. The PCE-322ALEQ SPL meter has a logger function, which allows storage of up to 32700 readings.


- Automatic range: 30 ... 130 dB
- Manual range: 30 ... 80 / 50 ... 100 / 80 ... 130 dB
- Resolution: 0.1 dB
- Accuracy: ±1.4 dB
- Memory capacity: 32700 values
- Incl. software for LEQ calculation


Important! The LEQ value is only calculated by the software after the data transfer from the device to the PC or laptop.

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RE110P
The temperature controller is used for temperature and process control. The various inputs and outputs, which are installed as standard on the PID controller, make it possible for the PID controller to be used universally.

Measurement functions:
- Process flow
- mV
- Process voltage
- Resistance
- Autotune PID
- Memory for several PID parameters
- RS485 Modbus interface
- 2 measuring inputs
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RCM 12
The temperature meter PCE-RCM 12 is used for indicative testing of environmental parameters. The temperature meter PCE-RCM 12 enables the measurement of CO2, fine dust, temperature and relative humidity. The bright display of the temperature meter provides information about these parameters. 


- Fine dust, CO2, formaldehyde, humidity, temperature
- Particle size channels: PM 2.5 / PM 10
- Temperature measuring range: -20 ... 70°C / -4 ... 158°F
- Humidity measuring range: 0 ... 100% r.H.
- Formaldehyde measuring range: 0.00 ... 5.00 mg/m³
- CO2 measuring range: 0 ... 9999 ppm
- For indicative measurements
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RCM 12
The thermometer PCE-RCM 12 is used for indicative testing of environmental parameters. The thermometer PCE-RCM 12 enables the measurement of CO2, fine dust, temperature and relative humidity. The bright display of the thermometer provides information about these parameters. 


- Fine dust, CO2, formaldehyde, humidity, temperature
- Particle size channels: PM 2.5 / PM 10
- Temperature measuring range: -20 ... 70°C / -4 ... 158°F
- Humidity measuring range: 0 ... 100% r.H.
- Formaldehyde measuring range: 0.00 ... 5.00 mg/m³
- CO2 measuring range: 0 ... 9999 ppm
- For indicative measurements
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-RE110P
The 2 channel universal input controller is used for temperature and process control. The various inputs and outputs, which are installed as standard on the PID controller, make it possible for the PID controller to be used universally.

Measurement functions:
- Process flow
- mV
- Process voltage
- Resistance
- Autotune PID
- Memory for several PID parameters
- RS485 Modbus interface
- 2 measuring inputs
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VDL 24I
For this vibration analyzer PCE-VDL 24I the acceleration sensor is delivered with a sampling rate of 1600 Hz. The sensor measures the acceleration, which is currently acting on it (3 axes), for example shock / vibration. The measurements take place at predetermined (selectable) time intervals.

- 3-Axis acceleration up to 1600 Hz and ±16 g
- 32 GB SD memory card
- Evaluation software
- Small design: 86.8 x 44.1 x 22.2 mm / 3.4 x 1.7 x 0.87 in
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-VDL 24I
For this vibration meter PCE-VDL 24I the acceleration sensor is delivered with a sampling rate of 1600 Hz. The sensor measures the acceleration, which is currently acting on it (3 axes), for example shock / vibration. The measurements take place at predetermined (selectable) time intervals.

- 3-Axis acceleration up to 1600 Hz and ±16 g
- 32 GB SD memory card
- Evaluation software
- Small design: 86.8 x 44.1 x 22.2 mm / 3.4 x 1.7 x 0.87 in
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT-225A

PCE-HT-225A is a heavy-duty concrete hardness tester or concrete test hammer, also called a concrete rebound hammer or Swiss hammer, used to measure surface hardness and material compression strength. Suitable for use with concrete, rock and building materials, this rugged, manufacturer-calibrated rebound hammer is both easy to use and built to last.


- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² or 1450 ... 8702 psi
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- kg/cm², psi, and MPa conversion tables 
- Optional test anvil to verify accuracy listed under accessories 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PMI 4
The concrete moisture meter is a measuring device for nondestructive moisture measurement on concrete and screed. Here, the spring electrodes of the concrete moisture meter are pressed onto the surface to be tested. Within seconds, the concrete moisture meter will show the moisture content to the operator.

- Relative scale: 0 ... 100%
- Accuracy: ± 0.5%
- Resolution: 0.1%
- For measuring the moisture in concrete and screed
- Numeric and graphical view
- Eight spring electrodes are used for the measurement

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT-225A

PCE-HT-225A is a heavy-duty concrete hardness tester or concrete test hammer, also called a concrete rebound hammer or Swiss hammer, used to measure surface hardness and material compression strength. Suitable for use with concrete, rock and building materials, this rugged, manufacturer-calibrated rebound hammer is both easy to use and built to last.


- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² (1450 ... 8702 psi)
- Impact energy: 2.207 J or N-m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- kg/cm², psi, and MPa conversion tables 
- Optional test anvil to verify accuracy listed under accessories 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PMI 4
The damp meter is a measuring device for nondestructive moisture measurement on concrete and screed. Here, the spring electrodes of the damp meter are pressed onto the surface to be tested. Within seconds, the damp meter will show the moisture content to the operator.

- Relative scale: 0 ... 100%
- Accuracy: ± 0.5%
- Resolution: 0.1%
- For measuring the moisture in concrete and screed
- Numeric and graphical view
- Eight spring electrodes are used for the measurement

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT-225A

PCE-HT-225A is a heavy-duty concrete hardness tester or concrete test hammer, also called a concrete rebound hammer or Swiss hammer, used to measure surface hardness and material compression strength. Suitable for use with concrete, rock and building materials, this rugged, manufacturer-calibrated rebound hammer is both easy to use and built to last.


- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² or 1450 ... 8702 psi
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- kg/cm², psi, and MPa conversion tables 
- Optional test anvil to verify accuracy listed under accessories 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT-225A

PCE-HT-225A is a heavy-duty concrete hardness tester or concrete test hammer, also called a concrete rebound hammer or Swiss hammer, used to measure surface hardness and material compression strength. Suitable for use with concrete, rock and building materials, this rugged, manufacturer-calibrated rebound hammer is both easy to use and built to last.


- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² or 1450 ... 8702 psi
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- kg/cm², psi, and MPa conversion tables 
- Optional test anvil to verify accuracy listed under accessories 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-HT-225A

PCE-HT-225A is a heavy-duty concrete hardness tester or concrete test hammer, also called a concrete rebound hammer or Swiss hammer, used to measure surface hardness and material compression strength. Suitable for use with concrete, rock and building materials, this rugged, manufacturer-calibrated rebound hammer is both easy to use and built to last.


- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² (1450 ... 8702 psi)
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- kg/cm², psi, and MPa conversion tables 
- Optional test anvil to verify accuracy listed under accessories 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PMI 4
The moisture analyzer is a measuring device for nondestructive moisture measurement on concrete and screed. Here, the spring electrodes of the moisture analyzer are pressed onto the surface to be tested. Within seconds, the moisture analyzer will show the moisture content to the operator.

- Relative scale: 0 ... 100%
- Accuracy: ± 0.5%
- Resolution: 0.1%
- For measuring the moisture in concrete and screed
- Numeric and graphical view
- Eight spring electrodes are used for the measurement

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-PMI 4
The moisture meter is a measuring device for nondestructive moisture measurement on concrete and screed. Here, the spring electrodes of the moisture meter are pressed onto the surface to be tested. Within seconds, the moisture meter will show the moisture content to the operator.

- Relative scale: 0 ... 100%
- Accuracy: ± 0.5%
- Resolution: 0.1%
- For measuring the moisture in concrete and screed
- Numeric and graphical view
- Eight spring electrodes are used for the measurement

Manufacturer: PCE Instruments
Test Instruments manufacturer