The PCE-PGM 100 Surface Testing works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the Surface Testing emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.

- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU 
- Incl. ISO calibration certificate

The PCE-VE 330N is an industrial borescope, inspection camera or industrial endoscope for the non-destructive inspection (NDI) of engines, machines and more. This industrial borescope is an ideal tool for diagnosing issues in hard-to-reach places. The waterproof camera head features 4 LED lights with automatic illumination. In addition, digital image magnification or zoom of up to 2 times is available.

 

- Diameter camera head: Ø 5.5mm / 0.22"
- Interface: Mini-USB 1.1 and AV out
- Memory: 8 GB SD memory card (incl.)
- Cable length: 2 m / 6ft 6"

The PCE-VE 320N is an industrial borescope, inspection camera or industrial endoscope for the non-destructive inspection (NDI) of engines, machines and more. This industrial borescope is an ideal tool for diagnosing issues in hard-to-reach places. The waterproof camera head features 4 LED lights with automatic illumination. In addition, digital image magnification or zoom of up to 2 times is available.

 

- Diameter camera head: Ø 5.5 mm / 0.22"
- Cable length: 1 m / 3ft 3"
- Interface: mini-USB 1.1 and AV out
- Memory: 8 GB SD memory card (incl.)

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. These gloss test instruments allow you to measure very high gloss surfaces above 70 gloss units (GU).

The PCE-TG 300-NO5/90 is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: 1 ... 600 mm / 0.039 ... 23.62" (steel)
- Diameter: 10mm / 0.39"
- Sensor at 90° angle
- Minimum diameter of pipes: 20 x 3 mm / 0.787 ... 0.118"
- Frequency: 5 MHz
- Bluetooth

PCE-VE 200 is a car measuring device or inspection camera, for nondestructive evaluation (NDE) and machine diagnostics. The car measuring device provides excellent image quality at an affordable price. An ideal camera tool for diagnosing hard-to-reach places, the scope can be rotated 180 ° and offers 6 LED lights with adjustable intensity for optimal illumination. In addition, digital image magnification or zoom of up to 4 times is available.

Automotive Tester
- 3.5 in LCD display
- 3.28 ft cable length
- 0.18 in camera cable diameter
- 1/8 in camera head / CMOS chip image sensor
- 640 x 480 pixels AVI video resolution
- Micro SD card memory
- Micro USB 2.0 and TV outputs

Clamp Meter
This Clamp Meter has been developed to determine indirectly, the the AC/DC currents with high accuracy. A non-contact clamp meter and a torch to illuminate the area being measured, have been integrated into this device. The small size of this  Clamp Meter, makes it possible to use in small spaces with limited access.

- 4 digit LCD display with backlighting
- save function
- DCA zero rest function
- current tester, non-contact
- integrated light to illuminate measured area
- automatic range selection
- automatic disconnect
- clamp diameter: 18 mm 

 

PCE-VE 200 is a car measuring device for nondestructive evaluation (NDE) and machine diagnostics. The car measuring device provides excellent image quality at an affordable price. An ideal camera tool for diagnosing hard-to-reach places, the scope can be rotated 180° and offers 6 LED lights with adjustable intensity for optimal illumination. In addition, digital image magnification or zoom of up to 4 times is available.

Borescope
- 3.5 in LCD display
- 3.28 ft cable length
- 0.18 in camera cable diameter
- 1/8 in camera head / CMOS chip image sensor
- 640 x 480 pixels AVI video resolution
- Micro SD card memory
- Micro USB 2.0 and TV outputs

Air Flow Meter
The air flow meter PCE-VA 20-set is a measuring instrument for various wind related parameters. It has got an impeller diameter of ten centimeters. Moreover, if required, it is possible to order a set of flow hoods which provide a fast and reliable method which helps to use the 100 mm large impeller head optimally.

- incl. Flow hood
- 10 cm diameter impeller
- Backlight
- Automatic power off
- Extreme value measurement
- HOLD function
- Low battery indicator 

 

The PCE-TG 300-P5EE is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: P-E: 2 ... 600 mm / 0.07 ... 23.62", E-E: 2.5 ... 100 mm / 0.09 ...3.93"
- Diameter: 10mm / 0.39"
- Minimum diameter of pipes: 20 x 3 mm / 0.787 ... 0.118"
- Frequency: 5MHz
- Bluetooth
- incl. ISO calibration certificate

- Measuring range: 0 ... 500 N
- Resolution: 0.1 N
- Accuracy: ± 0.3% of the measuring range
- Memory for 100 measurements
- USB interface
- Graphic display

Motorised Force Test Stand PCE-VTS 50
- Force range: 500 N / 50 kg / 110 lb
- Distance display resolution: 0.02 mm
- Resolution: 1 mm/min
- Tensile and compression testing
- Travel: 270 mm / 10.6"

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

Digital force gauge PCE-DFG N 500 for tensile force measurement and pressure force measurement up to 500 N. The digital force gauge is for precise measurements with a resolution of 0.1 N.

 

- Measuring range: 0 ... 500 N
- Accuracy: ± 0.1% of the measuring range
- Memory for 100 measurements
- Pull and pressure force measurement
- 1600 Hz sampling rate
- Interface: USB
- 6 different measuring tips

The PCE-TG 300-HT5 is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: 1 ... 600 mm / 0.039 ... 23.62" (steel)
- Diameter: 12mm / 0.47"
- Minimum diameter of pipes: 30 mm / 1.18"
- Frequency: 5MHz
- Bluetooth
- incl. ISO calibration certificate

The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission

Digital Force Gage PCE-DFG N 500-ICA for tensile force measurement and pressure force measurement up to 500 N. The digital force gage is for precise measurements with a resolution of 0.1 N.

 

- Measuring range: 0 ... 500 N
- Accuracy: ± 0.1% of the measuring range
- Memory for 100 measurements
- Pull and pressure force measurement
- 1600 Hz sampling rate
- Interface: USB
- 6 different measuring tips
- Incl. ISO calibration certificate

Our motorized force gage can be coupled and operated in a wide variety of versions with our force gauges, the PCE series. The motorized force gage lets you carry out almost all of your compression and tensile force applications with repeatability. The use of the motorized force gage offers the operator the most precise equality of test bench and sample.

- Force range: max. 5000 N / 500 kg / 1100 lbs
- Travel: max. 300 mm / 11.8"
- Feed speed: 30 ... 230 mm/min / 1.18 ... 9.05 in/min
- Manual or automatic procedure
- incl. length measuring device: -150 … 150 mm / -5.9 … 5.9"

*** N.B. The mounting plate ADP-UNI accessory must be ordered for internal load cell force gauges ***

Our universal testing machine can be coupled and operated in a wide variety of versions with our force gauges, the PCE series. The universal testing machine lets you carry out almost all of your compression and tensile force applications with repeatability. The use of the universal testing machine offers the operator the most precise equality of test bench and sample.

- Force range: max. 5000 N / 500 kg / 1100 lbs
- Travel: max. 300 mm / 11.8"
- Feed speed: 30 ... 230 mm/min / 1.18 ... 9.05 in/min
- Manual or automatic procedure
- incl. length measuring device: -150 … 150 mm / -5.9 … 5.9"

*** N.B. The mounting plate ADP-UNI accessory must be ordered for internal load cell force gauges ***

The PCE-TG 300-NO2 is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: 3.0 … 300.0 mm / 0.118 ... 11.81" (steel)
- Diameter: 14 mm / 0.55"
- Minimum diameter of pipes: 30 mm / 1.18"
- Frequency: 2.5 MHz
- Bluetooth
- incl. ISO calibration certificate