The HVAC meter is required as part of a control measurement or to quickly determine the flow in a pipeline and is a portable / easy-to-install measuring system. The HVAC meter works according to the transit time difference method. The measuring principle of the HVAC meter is quite simple.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe sizes: 50 … 720 mm (approx. 1.9 … 28")
                      20 …108 mm (approx. 0.8 … 4.2")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, Z
- Incl. sensors TDS-HM and TDS-HS on rails
- Incl. ISO Calibration Certificate

The HVAC Meter PCE-VE 355N3 is a two-way articulating videoscope, inspection camera, industrial endoscope or borescope for the non-destructive inspection (NDI) of small components and hard-to-reach places. The camera head features 5 LED lights with automatic illumination. Pictures and videos are saved to the included 8 GB SD card memory, allowing easy transfer to a PC.

- 2-way camera probe
- Diameter camera head: Ø 4.5mm / 0.18"
- Interface: Mini-USB 1.1 und AV out/in
- Memory: 8 GB SD memory card (incl.)
- Cable length: 3 m /  9ft 10"

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

- Measuring range: 10 ... 999.9 V
- AC voltage AC
- Alternating current AC
- Active power
- Power factor
- Phase angle
- Frequency
- Harmonic measurement
- Data memory: 512 kB 
  (non-volatile memory)
- incl. 4 current clamps / tapping terminals
- Standards: IP 30 / IEC 61 010, 600 V / CAT III
- incl. ISO Calibration Certificate 

The 3-Phase Power Meter / 3-Phase Power Analyzer is a power meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

- Measuring range: 10 ... 999.9 V
- AC voltage AC
- Alternating current AC
- Active power
- Power factor
- Phase angle
- Frequency
- Harmonic measurement
- Data memory: 512 kB 
  (non-volatile memory)
- incl. 4 current clamps / tapping terminals
- Standards: IP 30 / IEC 61 010, 600 V / CAT III
- incl. ISO Calibration Certificate 
- incl. ISO Calibration Certificate 

The PCE-PIC 40 HVAC meter is an ideal tool for any service technician who needs to visually inspect pipes and ducts. The HVAC meter PCE-PIC 40 has a 23 mm / 0.9 in camera head, which is attached to a glass fiber push cable.

- Cable diameter / head diameter: 23 mm / 0.9 in
- 40 m / 131 ft push cable
- Electronic meter count
- Battery and mains operation
- Waterproof up to 20 m / 66 ft 

The power analyzer PCE-PA6000 power analyzer can be used as a desktop or portable instrument for measuring active power, apparent power, power factor, energy consumption, AC voltage, AC current, DC voltage, DC current, resistance and frequency. The power / performance measurement can be performed with this power analyzer either directly with the supplied test leads, or indirectly by current clamps.

- Performance
- Power factor
- AC voltage and current
- DC voltage and current, resistance and frequency
- Incl. Data Cable and Test Leads
- Software available in the accessories tab
- incl. ISO Calibration Certificate

The power analyzer PCE-PA6000 power analyzer can be used as a desktop or portable instrument for measuring active power, apparent power, power factor, energy consumption, AC voltage, AC current, DC voltage, DC current, resistance and frequency. The power / performance measurement can be performed with this power analyzer either directly with the supplied test leads, or indirectly by current clamps.

- Performance
- Power factor
- AC voltage and current
- DC voltage and current, resistance and frequency
- Incl. Data Cable and Test Leads
- Software available in the accessories tab
- incl. ISO Calibration Certificate

The HVAC meter is required as part of a control measurement or to quickly determine the flow in a pipeline and is a portable / easy-to-install measuring system. The HVAC meter works according to the transit time difference method. The measuring principle of the flow meter is quite simple.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe sizes: 50 … 720 mm (approx. 1.9 … 28")
                      20 …108 mm (approx. 0.8 … 4.2")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, Z
- Incl. sensors TDS-HM and TDS-HS on rails

This car measuring device was developed for the indirect measurement of AC/DC currents as well as the frequency. A non-contact voltage tester function and a torch/flashlight for illuminating the measuring point have also been integrated into this car measuring device.

- AC/DC current, AC voltage and frequency measurement
- AC voltage test (contactless test):
   100 VAC to 600 VAC 50/60Hz 100 VAC to 600 VAC 50/60Hz
- DCA zero point function

This clamp meter was developed for the indirect measurement of AC/DC currents as well as the frequency. A non-contact voltage tester function and a torch/flashlight for illuminating the measuring point have also been integrated into this clamp meter.

- AC/DC current, AC voltage and frequency measurement
- AC voltage test (contactless test):
   100 VAC to 600 VAC 50/60Hz 100 VAC to 600 VAC 50/60Hz
- DCA zero point function

PCE-VE 200 is a video inspection camera, for nondestructive evaluation (NDE) and machine diagnostics. The PCE-VE 200 video inspection camera provides excellent image quality at an affordable price. An ideal tool for diagnosing hard-to-reach places, the scope can be rotated 180 ° and offers 6 LED lights with adjustable intensity for optimal illumination. In addition, digital image magnification or zoom of up to 4 times is available.

Inspection Camera
- 3.5 in LCD display
- 3.28 ft cable length
- 0.18 in cable diameter
- 1/8 in camera head / CMOS chip image sensor
- 640 x 480 pixels AVI video resolution
- Micro SD card memory
- Micro USB 2.0 and TV outputs

Clamp Meter
This Clamp Meter has been developed to determine indirectly, the the AC/DC currents with high accuracy. A non-contact clamp meter and a torch to illuminate the area being measured, have been integrated into this device. The small size of this  Clamp Meter, makes it possible to use in small spaces with limited access.

- 4 digit LCD display with backlighting
- Save function
- DCA zero rest function
- Current tester, non-contact
- Integrated light to illuminate measured area
- Automatic range selection
- Automatic disconnect
- Clamp diameter: 18 mm 

 

PCE-VE 200 is a videoscope or inspection camera, for nondestructive evaluation (NDE) and machine diagnostics. The PCE-VE 200 videoscope provides excellent image quality at an affordable price. An ideal camera tool for diagnosing hard-to-reach places, the scope can be rotated 180 ° and offers 6 LED lights with adjustable intensity for optimal illumination. In addition, digital image magnification or zoom of up to 4 times is available.

Videoscope
- 3.5 in LCD display
- 3.28 ft cable length
- 0.18 in camera cable diameter
- 1/8 in camera head / CMOS chip image sensor
- 640 x 480 pixels AVI video resolution
- Micro SD card memory
- Micro USB 2.0 and TV outputs

Clamp Meter
This Clamp Meter has been developed to determine indirectly, the the AC/DC currents with high accuracy. A non-contact clamp meter and a torch to illuminate the area being measured, have been integrated into this device. The small size of this  Clamp Meter, makes it possible to use in small spaces with limited access.

- 4 digit LCD display with backlighting
- save function
- DCA zero rest function
- current tester, non-contact
- integrated light to illuminate measured area
- automatic range selection
- automatic disconnect
- clamp diameter: 18 mm 

 

[more]