The industrial borescope has a 1.2 m / 3.9 ft long endoscope cable. With a diameter of only 2 mm, cavities with the smallest access can be viewed with the help of this industrial borescope. The camera head of this industrial borescope can move freely in 4 directions.

- Cable / head diameter: 2 mm
- Direction of movement camera head: 4-way
- Camera head length: 7 mm
- Bending radius: 6 mm
- 1.2 m / 3.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP58 camera cable
- 400 x 400 pixel image resolution

The PCE-TG 300-HT5 is an ultrasonic thickness tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the ultrasonic thickness tester. Wall thicknesses under a coating can also be measured with the ultrasonic thickness tester.

- Measuring range: 1 ... 600 mm / 0.039 ... 23.62" (steel)
- Diameter: 12mm / 0.47"
- Minimum diameter of pipes: 30 mm / 1.18"
- Frequency: 5MHz
- Bluetooth
- incl. ISO calibration certificate

With the PCE-DLT 10 test stand, the water vapour resistance of samples is tested according to AMK-MB-005 Issued on 04/2015 Humidity and Climatic Resistance Test Module 1 (water vapour loading).

- Steam test according to AMK-MB-05
- Max. 5 test specimens
- Automatic test sequence with constant temperature
- Data logger
- Determination of moisture expansion
- Checking of joint formation and edge release

 

The car measuring device has a 1.2 m / 3.9 ft long endoscope cable. With a diameter of only 2 mm, cavities with the smallest access can be viewed with the help of this car measuring device. The camera head of this car measuring device can move freely in 4 directions.

- Cable / head diameter: 2 mm
- Direction of movement camera head: 4-way
- Camera head length: 7 mm
- Bending radius: 6 mm
- 1.2 m / 3.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP58 camera cable
- 400 x 400 pixel image resolution

The snake camera has a 1.2 m / 3.9 ft long endoscope cable. With a diameter of only 2 mm, cavities with the smallest access can be viewed with the help of this snake camera. The camera head of this snake camera can move freely in 4 directions.

- Cable / head diameter: 2 mm
- Direction of movement camera head: 4-way
- Camera head length: 7 mm
- Bending radius: 6 mm
- 1.2 m / 3.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP58 camera cable
- 400 x 400 pixel image resolution

The videoscope has a 1.2 m / 3.9 ft long endoscope cable. With a diameter of only 2 mm, cavities with the smallest access can be viewed with the help of this videoscope. The camera head of this videoscope can move freely in 4 directions.

- Cable / head diameter: 2 mm
- Direction of movement camera head: 4-way
- Camera head length: 7 mm
- Bending radius: 6 mm
- 1.2 m / 3.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP58 camera cable
- 400 x 400 pixel image resolution

The condition monitoring inspection camera has a 1.2 m / 3.9 ft long endoscope cable. With a diameter of only 2 mm, cavities with the smallest access can be viewed with the help of this condition monitoring inspection camera. The camera head of this condition monitoring inspection camera can move freely in 4 directions.

- Cable / head diameter: 2 mm
- Direction of movement camera head: 4-way
- Camera head length: 7 mm
- Bending radius: 6 mm
- 1.2 m / 3.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP58 camera cable
- 400 x 400 pixel image resolution

The inspection camera has a 1.2 m / 3.9 ft long endoscope cable. With a diameter of only 2 mm, cavities with the smallest access can be viewed with the help of this inspection camera. The camera head of this inspection camera can move freely in 4 directions.

- Cable / head diameter: 2 mm
- Direction of movement camera head: 4-way
- Camera head length: 7 mm
- Bending radius: 6 mm
- 1.2 m / 3.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP58 camera cable
- 400 x 400 pixel image resolution

- Melting rate: 0.1 to 400.0 g / 10 min
- Heating temperature: 120 ... 400°C / 248 ... 752°F
- Measuring accuracy temperature: ± 0.2°C / 0.36°F
- Resolution: 0.1°C / 0.18°F
- Large 7" TFT touch display
- Already pre-set materials
- Various weights included
- Standards: ISO1133-1997, ASTM 1238-04C, GB / T3682-2000

The HVAC meter has a 1.2 m / 3.9 ft long endoscope cable. With a diameter of only 2 mm, cavities with the smallest access can be viewed with the help of this HVAC meter. The camera head of this HVAC meter can move freely in 4 directions.

- Cable / head diameter: 2 mm
- Direction of movement camera head: 4-way
- Camera head length: 7 mm
- Bending radius: 6 mm
- 1.2 m / 3.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP58 camera cable
- 400 x 400 pixel image resolution

The automotive tester has a 1.2 m / 3.9 ft long endoscope cable. With a diameter of only 2 mm, cavities with the smallest access can be viewed with the help of this automotive tester. The camera head of this automotive tester can move freely in 4 directions.

- Cable / head diameter: 2 mm
- Direction of movement camera head: 4-way
- Camera head length: 7 mm
- Bending radius: 6 mm
- 1.2 m / 3.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP58 camera cable
- 400 x 400 pixel image resolution

PCE-5000 is a portable hardness tester that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys with a minimum thickness of 2 mm / .08 in Non-destructive testing produces microscopic indentation.

- Measurement according to ASTM A1038 ultrasonic contact impedance (UCI) method
- Measurement units: Rockwell A (HRA), Rockwell B (HRB), Rockwell C (HRC), Brinell (HB), Vickers (HV) and MPa (N/mm²) SI units
- Measurement ranges: 61-85.6 HRA, 41-100 HRB, 20.3-68 HRC, 85-650 HB, 50-999 HV, 255-2180 MPa (N/mm²)
- Accuracy: ± 1.5 HR, ± 3% HB, ± 3% HV, Repeatability: ± 0.3%
- Memory size: 1,000 groups for measurement data and 20 groups for calibration data
- Different probe types (also automatic motorized probes) available

Our motorized force test stand can be coupled and operated in a wide variety of versions with our force gauges, the PCE series. The motorized force test stand lets you carry out almost all of your compression and tensile force applications with repeatability. The use of the motorized force test stand offers the operator the most precise equality of test bench and sample.

- Force range: max. 5000 N / 500 kg / 1100 lbs
- Travel: max. 300 mm / 11.8"
- Feed speed: 30 ... 230 mm/min / 1.18 ... 9.05 in/min
- Manual or automatic procedure
- incl. length measuring device: -150 … 150 mm / -5.9 … 5.9"

*** N.B. The mounting plate ADP-UNI accessory must be ordered for internal load cell force gauges ***

The PCE-830-2 Power Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This Power Meter also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

The PCE-830-2 Clamp Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp Meter also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

The PCE-830-2 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

The PCE-830-2 Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This Power Analyzer also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

The PCE-830-2 Data Logger is used for measuring one to three phases of electrical quantities for alternating current (AC). This Data Logger also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)