The PCE-GM 60Plus gloss meter is a portable handheld 60 degree gloss meter. This coating and paint gloss meter measures the gloss units (GU) on a material's surface. The rechargeable gloss meter or gloss tester uses reflected light for gloss measurement per ISO 2813, GB/T 9754, ASTM D523 and ASTM D2457 standards.

- Measuring geometry: 60° degree angle
- Measuring range: 0 ... 200 GU
- Measuring accuracy ±1.5 GU
- 3.5" TFT touchscreen display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

- Measures Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc in both Metric (µm) and Imperial (µinch)
- Ra, Rq, Rc : 0.005 μm…16 μm / 0.197 µinch ... 629.921 µinch measurement range
- Rz, Rt Rp, Rv: 0.020 µm … 200 µm / 0.797 µinch ... 7874.016 µinch measurement range
- Rsm: 5 μm …1000 μm / 1968 µinch … 3937 µinch measurement range
- Rsk: -1 …. 1 measurement range
- Measurement accuracy: <± 10% and Repeatability < 6%
- Robust Piezoelectric sensor
- Saves up to 20 Data points
- 3 different cutoff wavelengths
- Micro USB Interface
- PC Software
- Built-in rechargeable li-ion battery
- Incl. ISO Calibration Certificate

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

The surface testing gloss meter is equipped with an external gloss sensor. The measuring surface of Ø 4.5 mm of the gloss meter also contributes significantly to being able to carry out measurements on small surfaces that are difficult to access.

- Measurement geometry: 60°
- Measuring range up to 1000 GU
- Measuring surface: Ø 4.5 mm
- Data storage: 1245 measured values
- Interface: Micro USB

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This gloss meter allows you to measure very high gloss surfaces above 70 gloss units (GU).

- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

PCE-PGM 60 is a portable handheld gloss meter or gloss tester used to evaluate the shine on different material surfaces. The gloss tester includes a 3.5" TFT touchscreen display, internal memory and PC-compatible software for detailed analysis.

- Measuring geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate
- Includes PC-compatible software for detailed analysis

- Measuring range: 0 ... 12 A DC
- Three different test functions
- PC interface for data transfer
- Switchable graphic view
- Application, e.g. photovoltaic systems
- incl. ISO Calibration Certificate

- Measuring range: 0 ... 12 A DC
- Three different test functions
- PC interface for data transfer
- Switchable graphic view
- Application, e.g. photovoltaic systems
- incl. ISO Calibration Certificate

The Bluetooth surface testing - roughness tester is used to determine surface roughness. The compact roughness tester is a handheld device for mobile use. Due to the power supply via a powerful battery, it can be used directly on site. The roughness tester is used in the laboratory, in production and everywhere where the roughness of surfaces is to be determined.

- Measures Ra, Rz, Rq and Rt in Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.005 ... 16.00 μm / 0.197 µinch... 629.921 µinch measurement range
- Rz, Rt: 0.002 ... 200.0 μm / 0.079 µinch... 7874.016 µinch measurement range
- Induction method with Diamond sensor
- Large OLED display
- Display for the position of the probe
- Micro-USB interface
- Bluetooth
- Download the app for free from the Google Play Store
- incl. ISO Calibration Certificate

- Measuring range: 0 ... 12 A DC
- Three different test functions
- PC interface for data transfer
- Switchable graphic view
- Application, e.g. photovoltaic systems
- incl. ISO Calibration Certificate

The environmental meter PCE-428-EKIT-ICA, from the field of environmental measurement technology, is an optimal sound level meter for measurements at workplaces, construction sites, in traffic, airports, etc. The environmental meter is equipped with an octave band frequency filter. Optionally, the environmental meter can be upgraded with a 1/3 octave band filter. The additional kit for outdoor sound measurement makes it possible to measure outdoor noise with an environmental meter over a long period of time, even in the rain.

 

- Accuracy class 2 
- A, B, C & Z frequency rating
- Fast, Slow, Pulse and Peak time weighting
- Statistics function
- 1/1 octave band included
- 1/3 octave band optional
- incl. outdoor noise level meter kit PCE-4xx-EKIT
- Outdoor measurement of sound and noise
- incl. ISO calibration certificate

- Measuring range: 0 ... 1250 µm
- Accuracy: ± (1% + 1 µm)
- Resolution: 0.1 µm (<99.9 µm), 1 µm (> 100 µm)
- Measurement data storage for up to 500 data
- Data transfer via Wifi and USB
- Two different probes for NFe and Fe (included)
- incl. ISO Calibration Certificate

The Class 1 outdoor SPL meter PCE-430-EKIT-ICA with integrated data logger meets all requirements for noise measurement and frequency analysis. This integrated precision pulse outdoor SPL meter kit follows all valid standards and guidelines, and is designed for use outdoors in all weather. Typical applications are the measurement of workplace noise, compliance, environmental noise detection, selection of hearing protector selection, selection of appropriate noise abatement measures and noise exposure estimation.

 

- Accuracy class 1 
- A, B, C & Z frequency rating
- Fast, Slow, Pulse and Peak time weighting
- Statistics function
- 1/1 octave band included
- 1/3 octave band optional
- Incl. Outdoor Alarm Noise Meter Kit PCE-4xx-EKIT
- Outdoor measurement of sound and noise
- Incl. ISO calibration certificate

The Class 1 outdoor decibel meter PCE-430-EKIT-ICA with integrated data logger meets all requirements for noise measurement and frequency analysis. This integrated precision pulse outdoor decibel meter kit follows all valid standards and guidelines, and is designed for use outdoors in all weather. Typical applications are the measurement of workplace noise, compliance, environmental noise detection, selection of hearing protector selection, selection of appropriate noise abatement measures and noise exposure estimation.

 

- Accuracy class 1 
- A, B, C & Z frequency rating
- Fast, Slow, Pulse and Peak time weighting
- Statistics function
- 1/1 octave band included
- 1/3 octave band optional
- Incl. Outdoor Alarm Noise Meter Kit PCE-4xx-EKIT
- Outdoor measurement of sound and noise
- Incl. ISO calibration certificate

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60°. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 1000 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
 

 

The Leeb Surface Testing PCE-900-ICA measures the hardness of nine different metals using the Leeb rebound method. This means that with the Surface Testing a firing pin bounces on a metallic surface and the intensity of the rebound is used as an indicator of the material hardness. The Surface Testing measures the metal hardness in 6 different hardness scales. 

- Measurement according to Leeb Rebound method
- Testing of HRC, HRB, HV, HB, HSD
- Measurement Range: 200-900 HLD / 13-99 HRB / 20-68 HRC / 20-655 HB / 80-940 HV / 32-99 HSD
- Accuracy: 0.80% / Repeatability: 1.10%
- Incl. type D Leeb probe
- Optional Software Available
- incl. ISO Calibration Certificate

The Surface Tester PCE-RT 11-ICA is a portable measuring instrument for determination of surface roughness according to Ra, Rz, Rq and Rt in just one device. The small roughness tester is especially designed for fast measuring of roughness. The roughness is a term of surface physics that describes unevenness of surface height.


- Measures Ra, Rz, Rq and Rt in both Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.05 µm … 10 µm / 0.002 µinch … 394 µinch measurement range
- Rz, Rt: 0.1 µm … 50 µm / 0.004 µinch …1968 µinch measurement range
- Robust Piezoelectric sensor
- Accuracy: ± 15% and Repeatability < 12%
- Built-in rechargeable li-ion battery
- Inc. ISO Calibration Certificate

PCE-GM 60Plus is a portable handheld 60-degree reflective surface-testing gloss meter or gloss tester used to measure the gloss units (GU) on a material's surface. This rechargeable gloss meter uses reflected light for gloss measurement per ISO 2813, GB/T 9754, ASTM D523 and ASTM D2457 standards.

- Measuring geometry: 60° degree angle
- Measuring range: 0 ... 200 GU
- 3.5" TFT touchscreen display
- Measuring accuracy ±1.5 GU
- Light source: D65
- Wave length: 400-700 nm