The NDT Tester - Gloss Meter is equipped with an external gloss sensor. The measuring surface of Ø 4.5 mm of the gloss meter also contributes significantly to being able to carry out measurements on small surfaces that are difficult to access.

- Measurement geometry: 60°
- Measuring range up to 1000 GU
- Measuring surface: Ø 4.5 mm
- Data storage: 1245 measured values
- Interface: Micro USB
- Incl. ISO calibration certificate

- Range : 0 ... 200 gloss units / highlights
- Accuracy: ± 1 gloss units
- Repeatability: ± 0.5 gloss units
- Optical angle: 20°, 45°, 75°
- For medium and high gloss
- Measurements on textiles and paper possible

The PCE-GM 60Plus gloss meter is a portable handheld 60 degree gloss meter. This coating and paint gloss meter measures the gloss units (GU) on a material's surface. The rechargeable gloss meter or gloss tester uses reflected light for gloss measurement per ISO 2813, GB/T 9754, ASTM D523 and ASTM D2457 standards.

- Measuring geometry: 60° degree angle
- Measuring range: 0 ... 200 GU
- Measuring accuracy ±1.5 GU
- 3.5" TFT touchscreen display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

- Measuring range up to 1000 GU
- For measurements on small surfaces
- Precise measurements thanks to high accuracy
- Micro-USB interface for the PC connection
- Data memory for later evaluations
- Data memory: 1,245 measured values
- Incl. ISO calibration certificate

The PCE-PGM 100 Surface Testing works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the Surface Testing emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.

- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU 
- Incl. ISO calibration certificate

The portable and easy-to-use surface testing - roughness tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The roughness tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface
- Incl. ISO calibration certificate

The PCE-PGM 60 Surface Testing has a measuring geometry of 60°. The Surface Testing is used to analyze surfaces of different materials. Gloss measurements are particularly carried out in the production industry where products must have exactly the same characteristics.

- Measurement geometry: 60° degree angle
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Measuring range: 0 ... 300 GU
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate
- Includes PC-compatible software for detailed analysis

The gloss meter is equipped with an external gloss sensor. The measuring surface of Ø 4.5 mm of the gloss meter also contributes significantly to being able to carry out measurements on small surfaces that are difficult to access.

- Measurement geometry: 60°
- Measuring range up to 1000 GU
- Measuring surface: Ø 4.5 mm
- Data storage: 1245 measured values
- Interface: Micro USB
- Incl. ISO calibration certificate

- Measuring range up to 1000 GU
- For measurements on small surfaces
- Precise measurements thanks to high accuracy
- Micro-USB interface for the PC connection
- Data memory for later evaluations
- Data memory: 1,245 measured values
- Incl. ISO calibration certificate

The PCE-PGM 100 Surface Testing works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the Surface Testing emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.

- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU 

 

- Large measuring range:  Rz: 0.02 μm ... 320 μm; Ra, Rq: 0.005 μm ... 32 μm
- Accuracy of ± 10% and repeat accuracy of ± 6%
- Touchscreen configuration and Android/printer bluetooth connectivity 
- Sensor has diamond test head with 90-degree cone angle
- Optional sensors and extension rod for small holes and curved surfaces 
- Incl. ISO calibration certificate

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. These gloss test instruments allow you to measure very high gloss surfaces above 70 gloss units (GU).

The PCE-GM 60Plus NDT tester or gloss meter is a portable handheld 60 degree gloss meter. This coating and paint gloss meter measures the gloss units (GU) on a material's surface. The rechargeable gloss meter or gloss tester uses reflected light for gloss measurement per ISO 2813, GB/T 9754, ASTM D523 and ASTM D2457 standards.

- Measuring geometry: 60° degree angle
- Measuring range: 0 ... 200 GU
- Measuring accuracy ±1.5 GU
- 3.5" TFT touchscreen display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

A gloss meter is a tester for determining surface gloss. Thereby, with the glossmeter, spectral reflections of a light beam that hits the surface, are measured. The touch screen allows for easy navigation.

- Measuring geometries: 20° / 60° / 85°
- Measuring range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm

- Range : 0 ... 200 gloss units / highlights
- Accuracy: ± 1 gloss units
- Repeatability: ± 0.5 gloss units
- Optical angle: 20°, 45°, 75°
- For medium and high gloss
- Measurements on textiles and paper possible

The surface tester PCE-RT 2000BT-ICA is used for accurate measurement of surface roughness. The surface tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- Bluetooth
- 3 different cut-off wavelengths
- Download free app from the Google Play Store
- incl. ISO Calibration Certificate

The Class 1 IoT meter can be used, e.g., for sound measurement of street noise, aircraft and train noise, event noise, noise coming from construction sites, ports, factories involving heavy machinery, airport/bus stations, stadiums, horse/motor racing tracks etc. The weather conditions do not matter, and hail, snow, rain and similar are no problem for this system for outdoor noise monitoring. The IoT meter is equipped with a GPS receiver which allows the user to assign the measured values to an exact position.

 

- Accuracy class 1
- GPS function
- A, B, C & Z frequency rating
- Fast, Slow, Pulse and Peak time weighting
- Statistics function
- 1/1 octave band included
- 1/3 octave band optional
- Incl. Outdoor Alarm Noise Meter Kit PCE-4xx-EKIT
- Outdoor measurement of sound and noise
- Incl. ISO calibration certificate