The PCE-830-3 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

The HVACR Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This HVACR Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.2 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 x 97 x 46 mm / 9.6 x 3.8 x 1.8 in
- Incl. ISO calibration certificate

The PCE-DDD 10 Shore D Material Tester is a portable handheld device used to check Shore D hardness in hard rubber and thermoplastic. This digital Material Tester has a reading accuracy of 0.1 hardness units. The Material Tester comes manufacturer calibrated and can be optionally certified to ISO standards for an additional fee (see accessories for details).

- Portable handheld digital device
- For Shore D hardness testing
- Single and serial measurements
- Data transfer to PC

PCE-PA 8000 is a portable handheld power analyzer used for the testing and inspection of 3-phase / 4-wire, 3-phase / 3-wire, 1-phase / 2-wire and 1-phase / 3-wire electrical circuits. This handy power quality analyzer not only measures multiple electrical properties in real time, but also saves the measurement data in .xls format to the included SD card memory for quick and easy data transfer and analysis using Microsoft Excel.

- True RMS measurement for ACA, ACV
- True power: W, KW, MW
- VA, KVA, MVA, VAR, KVAR, MVAR
- PF (power factor), phase angle (Φ)
- KWH, KVAH, KVARH, PFH
- Voltage measurement range: 10 ... 600 ACV
- Current measurement range: 0.2 ... 1200 ACA
- Real-time current, voltage and power consumption measurement
- Built-in data recorder with adjustable sample rate: 2 ... 7,200 sec.

The automotive tester PCE-VE 350HR3 is a two-way articulating videoscope, industrial endoscope, borescope or inspection camera for the non-destructive inspection (NDI) of hard-to-reach places. The waterproof camera head features 6 LED lights (4 front, 2 side) for optimal illumination. In addition, digital image magnification or zoom of up to 2 times is available, plus boost functionality for improved image quality in the dark.

- With boost function: better images in dark surroundings
- 2 additional side LEDs for better lighting
- Image rotation possible
- Diameter: Ø 6 mm / 0.24"
- 2-way camera
- Memory: 8 GB SD memory card (incl.)
- Cable length: 3 m / 9ft 10"

The PCE-DDA 10 Shore A Material Tester is a portable handheld device used to check Shore A hardness in soft gums, elastomers, natural rubber, neoprenes, casting resin, white PVC, leather, etc. This digital Material Tester has a reading accuracy of 0.1 hardness units. The Material Tester comes manufacturer calibrated and can be optionally certified to ISO standards for an additional fee (see accessories for details).

- Portable handheld digital device
- For Shore A hardness testing
- Single and serial measurements
- Data transfer to PC

The PCE-DDD 10 shore hardness tester and durometer is an ergonomic device to check Shore D hardness in materials such as hard rubber and thermoplastic. It has been designed with a very high quality.  The durometer (as all test instruments) comes manufacturer calibrated and can additionally be lab certified to ISO standards.

- Handheld device
- For Shore D measurements
- Single and Serial Measurements
- Data transfer to PC

 

With the environmental tester it is possible to carry out quick and precise analysis of the pH concentration of liquid samples. For example, with the environmental tester it is possible to check alkaline solutions, water, wine, milk and many other liquids for the pH content.

- pH measuring range: -2.000 ... +19.999 pH
- Resolution: 0.1 / 0.01 pH
- Measuring range mV: -1999.9 ... +1999.9 mV
- Resolution: 1 mV
- Temperature measuring range: -10 ... +110 °C / 14 ... 230 °F
- Resolution: 0.1 °C
- USB and Bluetooth interface
- Memory for 300 measured values
- Live viewing software
- 3 point calibration
- incl. ISO Calibration Certificate

PCE-PST 1 adhesion tester is designed to check the adhesive force of edges and edge bands on support materials. With the adhesion tester, checks can be made with respect to the quality of workmanship. Feed speed, travel distance, tension, and traction angle are fixed. Ball transfer units on the guide surface of the Test Stand reduce the coefficient of friction. Likewise the self-locking jaws and smooth guide rollers always guarantee reproducible and comparable results.

- Measuring range: 500 N / 50 kg / 110 lbs
- Measurable edge thickness: 0.4 mm ... 3.5 mm
- Measurable thicknesses: 10 mm ... 64 mm
- Velocity: 0.3 m / min 

 

The roughness tester PCE-RT 2000-ICA is used for accurate measurement of surface roughness. The roughness tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- 3 different cut-off wavelengths
- PC software
- incl. ISO Calibration Certificate

The PCE-DDD 10 shore hardness tester is an ergonomic device to check Shore D hardness in materials such as hard rubber and thermoplastic. It has been designed with a very high quality.

- Handheld device
- For Shore D measurements
- Single and Serial measurements
- Data transfer to PC
- Incl. ISO Calibration Certificate

With this HVAC meter, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the HVAC meter consists of braided tungsten.

- Diameter: Ø2.2mm / 0.08"
- Cable length: 1m / 3.2 ft
- Camera direction: 90°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The portable and easy-to-use material tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The material tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface
- Incl. ISO calibration certificate

The PCE-DDA 10 shore Material Tester is an ergonomic device to check Shore hardness in gum, plastic and other non-metallic materials. It has been designed with a very high quality. The PCE-DDA 10 Material Tester is mainly used for soft gums, elastomers, natural rubber, neoprenes, casting resin, white PVC, leather, etc. It has a reading accuracy of 0.1 hardness units.

- Handheld device
- For Shore A measurements
- Single and Serial Measurements
- Data transfer to pc
- Incl. ISO Calibration Certificate

The automotive tester PCE-VE 355N is a two-way articulating videoscope, borescope, inspection camera or industrial endoscope for the non-destructive inspection (NDI) of small components and hard-to-reach places. The camera head features 5 LED lights with automatic illumination. Pictures and videos are saved to the included 8 GB SD card memory, allowing easy transfer to a PC.

- 2-way camera probe
- Diameter camera head: Ø 4.5mm / 0.18"
- Interface: Mini-USB 1.1 und AV out/in
- Memory: 8 GB SD memory card (incl.)
- Cable length: 1.5 m / 4ft 11"

PCE-FD 20 is a portable ultrasonic tester or ultrasonic thickness gauge with a large LCD screen that displays A-scan maps of ultrasonic signals as well as B-scan cross sections. Ideal for use in mechanical engineering, aerospace and metallurgical applications, this high-frequency ultrasound-based thickness meter uses a contact transducer (two different probes included; 45° and 90°) to measure material thickness and identify flaws and defects such as discontinuity in welds.

- Operating frequency range: 1 ... 10 MHz
- Measured time interval range: 6 ... 1000 microseconds (µs)
- Sound velocity: 1000 ... 9999 m/s 

 

The HVACR Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase HVACR Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate