- Measuring range: Fe: 0 ... 5000 µm, NFe: 0 ... 3000 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

- Measuring range: Fe: 0 ... 3000 µm, NFe: 0 ... 3000 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

- Measuring range: 0 ... 1250 µm
- Accuracy: ± (1% + 1 µm)
- Resolution: 0.1 µm (<99.9 µm), 1 µm (> 100 µm)
- Measurement data storage for up to 500 data
- Data transfer via wifi and USB
- Two different probes for NFe and Fe (included)

- Measuring range: 0 ... 1250 µm
- Accuracy: ± (1% + 1 µm)
- Resolution: 0.1 µm (<99.9 µm), 1 µm (> 100 µm)
- Measurement data storage for up to 500 data
- Data transfer via Wifi and USB
- Two different probes for NFe and Fe (included)
- incl. ISO Calibration Certificate

The Three-Phase Power Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This Three-Phase Power Meter also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. 

- PCE-830 + PCE-3007 flexible amp clamp (3000 A)
- Electrical conductor pick-up: 170 mm / 6.69 in diameter
- Length of electrical conductor: 610 mm / 24.0 in
- Dimensions: 257 mm x 155 mm x 57 mm / 10.1 in x 6.1 in x 2.2 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values - single phase)

The paint test equipment is used to accurately measure the correlated color temperature (CCT - in Kelvin), illuminance, chromaticity, excitation purity (Pe), luminous flux (in lumens - lm), RGB and dominant wavelength of light sources such as LED, organic LED (OLED) and other forms of organic electroluminescence (EL).

- Measuring range: 0.1 ... 150,000 lux / 0.01 ... 15,000 foot-candle
- Spectral wavelength range: 360 ... 780 nm
- Display: 3.2" colour LCD
- Chromaticity: Ev xy, Ev u'v'

The paint test equipment was developed for quality control and offers a high accuracy. When using the paint test equipment, you can choose between different color spaces (CIE LAB, XYZ, LCh, RGB, LUV). In addition, the paint test equipment comes with two different measuring apertures (Ø4 mm and Ø8 mm). After a measurement with the paint test equipment, the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the reference value easily.

- CIE LAB, XYZ, LCh, RGB, LUV
- White calibration
- Storage of 100 reference values and 20,000 samples
- Light sources D65, A, C, D50, F2, F6, F8, F10, F11 and F12
- Exchangeable measuring apertures
- Illumination/Viewing Angles 8°/d and CIE 10°

 

The automotive tester has a 1.2 m / 3.9 ft long endoscope cable. With a diameter of only 2 mm, cavities with the smallest access can be viewed with the help of this automotive tester. The camera head of this automotive tester can move freely in 4 directions.

- Cable / head diameter: 2 mm
- Direction of movement camera head: 4-way
- Camera head length: 7 mm
- Bending radius: 6 mm
- 1.2 m / 3.9 ft endoscope cable
- 5" monitor
- Image and video memory
- IP58 camera cable
- 400 x 400 pixel image resolution

The PCE-830-3 HVAC Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This HVAC Meter also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-3007 flexible amp clamp (3000 A)
- Electrical conductor pick-up: 170 mm / 6.69 in diameter
- Length of electrical conductor: 610 mm / 24.0 in
- Dimensions: 257 mm x 155 mm x 57 mm / 10.1 in x 6.1 in x 2.2 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values - single phase)

- Measuring range: Fe: 0 ... 500 µm, NFe: 0 ... 500 µm
- Accuracy after foil calibration: ±(1% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"

- Measuring range: 1.20 ... 300.0 mm  / 0.04 ... 11.81"
- Accuracy: ±0.5% of measured value + 0.05 mm
- Memory capacity: 1500 measured values
- Calibration reference on housing
- Probe temperature range: -10 ... 60 °C / 14 ... 140 °F

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

PCE-5000 is a portable material hardness tester that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys with a minimum thickness of 2 mm / .08 in. Non-destructive testing produces microscopic indentation.

- Measurement according to ASTM A1038 ultrasonic contact impedance (UCI) method
- Measurement units: Rockwell A (HRA), Rockwell B (HRB), Rockwell C (HRC), Brinell (HB), Vickers (HV) and MPa (N/mm²) SI units
- Measurement ranges: 61-85.6 HRA, 41-100 HRB, 20.3-68 HRC, 85-650 HB, 50-999 HV, 255-2180 MPa (N/mm²)
- Accuracy: ± 1.5 HR, ± 3% HB, ± 3% HV, Repeatability: ± 0.3%
- Memory size: 1,000 groups for measurement data and 20 groups for calibration data
- Different probe types (also automatic motorized probes) available

PCE-5000 is a portable material hardness tester that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys with a minimum thickness of 2 mm / .08 in. Non-destructive testing produces microscopic indentation.

- Measurement according to ASTM A1038 ultrasonic contact impedance (UCI) method
- Measurement units: Rockwell A (HRA), Rockwell B (HRB), Rockwell C (HRC), Brinell (HB), Vickers (HV) and MPa (N/mm²) SI units
- Measurement ranges: 61-85.6 HRA, 41-100 HRB, 20.3-68 HRC, 85-650 HB, 50-999 HV, 255-2180 MPa (N/mm²)
- Accuracy: ± 1.5 HR, ± 3% HB, ± 3% HV, Repeatability: ± 0.3%
- Memory size: 1,000 groups for measurement data and 20 groups for calibration data
- Different probe types (also automatic motorized probes) available

PCE-5000 is a portable hardness tester that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys with a minimum thickness of 2 mm / .08 in Non-destructive testing produces microscopic indentation.

- Measurement according to ASTM A1038 ultrasonic contact impedance (UCI) method
- Measurement units: Rockwell A (HRA), Rockwell B (HRB), Rockwell C (HRC), Brinell (HB), Vickers (HV) and MPa (N/mm²) SI units
- Measurement ranges: 61-85.6 HRA, 41-100 HRB, 20.3-68 HRC, 85-650 HB, 50-999 HV, 255-2180 MPa (N/mm²)
- Accuracy: ± 1.5 HR, ± 3% HB, ± 3% HV, Repeatability: ± 0.3%
- Memory size: 1,000 groups for measurement data and 20 groups for calibration data
- Different probe types (also automatic motorized probes) available

The paint testing equipment was developed for quality control and offers a high accuracy. When using the paint testing equipment, you can choose between different color spaces (CIE L*a*b, CIE L*a*b*C*h). After a measurement with the paint testing equipment, the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the reference value easily. Useful for determining color difference, chromaticity index, color sample database management, and color difference cumulative analysis.

- CIE L*a*b*C*h, CIE L*a*b*
- Measuring aperture: Ø8 mm
- optional liquid sample kit listed under accessories
- Storage of 100 reference values and 20,000 samples
- Light sources D65
- Illumination/Viewing Angles 8°/d 

 

The PCE-830-3 3-Phase Power Meter / 3-Phase Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Power Meter / 3-Phase Power Analyzer also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This gloss meter allows you to measure very high gloss surfaces above 70 gloss units (GU).

- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate