- Measures Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc in both Metric (µm) and Imperial (µinch)
- Ra, Rq, Rc : 0.005 μm…16 μm / 0.197 µinch ... 629.921 µinch measurement range
- Rz, Rt Rp, Rv: 0.020 µm … 200 µm / 0.797 µinch ... 7874.016 µinch measurement range
- Rsm: 5 μm …1000 μm / 1968 µinch … 3937 µinch measurement range
- Rsk: -1 …. 1 measurement range
- Measurement accuracy: <± 10% and Repeatability < 6%
- Robust Piezoelectric sensor
- Saves up to 20 Data points
- 3 different cutoff wavelengths
- Micro USB Interface
- PC Software
- Built-in rechargeable li-ion battery
- Incl. ISO Calibration Certificate

PCE-PA 8000 is a portable handheld Electrical Tester used for the testing and inspection of 3-phase / 4-wire, 3-phase / 3-wire, 1-phase / 2-wire and 1-phase / 3-wire electrical circuits. This handy power quality analyzer not only measures multiple electrical properties in real time, but also saves the measurement data in .xls format to the included SD card memory for quick and easy data transfer and analysis using Microsoft Excel.

- True RMS measurement for ACA, ACV
- True power: W, KW, MW
- VA, KVA, MVA, VAR, KVAR, MVAR
- PF (power factor), phase angle (Φ)
- KWH, KVAH, KVARH, PFH
- Voltage measurement range: 10 ... 600 ACV
- Current measurement range: 0.2 ... 1200 ACA
- Real-time current, voltage and power consumption measurement
- Built-in data recorder with adjustable sample rate: 2 ... 7,200 sec.
- Incl. ISO Calibration Certificate

PCE-1000N is a portable handheld Barcol hardness tester used to measure the hardness of pure aluminum, soft aluminum, thick aluminum alloy and aluminum sheets, strips, rods, castings and forgings. The hardness of fiber-reinforced (FRP) plastics, glass-reinforced (GRP) plastics, hard plastics and soft metals (such as copper or lead) also can be tested using this battery-powered digital Barcol impressor hardness meter.

- Measurement parameters: Barcol (HBA), Brinell (HB), Vickers (HV), Webster
  (HW)
  Rockwell (HRB / HRE / HRF / HRH)
- Measuring range: 0 ... 100 HBA / 25 ... 150 HB
- Accuracy: 81 ... 88 HBA: ± 1 HBA / 42 ... 48 HBA: ± 2 HBA
- Repeatability: 81 ... 88 HBA: ± 1.5 HBA / 42 ... 48 HBA: ± 2.5 HBA
- Resolution: 0.1 HBA
- Meets ASTM standards: E140-97; D2583-75; B648-78

 

The Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate

PCE-TDS 100HS-ICA is a portable handheld clamp-on ultrasonic flow tester used for non-invasive, unobstructed and highly accurate measurements of the flow velocity of liquids in metal, plastic and rubber pipes and tubes with a diameter of 20 … 108 mm / approx. 3/4 in ... 4in. Software sold separately - see accessories for details.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe size: DN 15 … 100, 20 … 108 mm (approx. 3/4 … 4")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, (N,W)
- Incl. sensors TDS-S1
- Incl. ISO Calibration Certificate

PCE-950 is a handheld metal hardness durometer used to determine the hardness of 10 different types of metal (i.e., cast steel, hammered steel, cold-rolled steel, stainless steel, cast iron, ductile iron, aluminum alloy, brass, bronze and forged copper alloy) according to the Leeb rebound method. In addition to Leeb hardness units, the metal hardness tester displays hardness measurements in Rockwell C, Rockwell B, Rockwell A, Brinell, Vickers and Shore hardness units.

- Measurement ranges: 19.8-68.5 HRC / 13.5-101.7 HRB / 59.1-85.8 HRA / 19-655 HB / 80-976 HV / 32.2-115 HS 
- Hardness units: HL, HRC, HRB, HRA, HB, HV, HS
- Accuracy: ± 2% / Repeatability: ± 2%
- Impact device: Type D (integrated)
- Data Analysis Software
- For use with hammered steel, cold-rolled steel, stainless steel, cast iron, ductile iron, aluminum alloy, brass, bronze and forged copper alloy metals

PCE-TDS 100H-ICA is a portable handheld clamp-on ultrasonic flow tester used for non-invasive, unobstructed and highly accurate measurements of the flow velocity of liquids in metal, plastic and rubber pipes and tubes with a diameter of 57 … 720 mm / approx. 2 ... 28 in.  Software sold separately - see accessories for details.

 

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe size: DN 50 … 700, 57 … 720 mm (approx. 2 … 28")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, Z
- Incl. sensors TDS-M1
- Incl. ISO Calibration Certificate

The roll hardness tester is an analog measuring device to determine concrete strength. The measuring method of the roll hardness tester is based on the Schmidt principle. With this measuring method, a kinetic impact energy hits the concrete from the roll hardness tester. The resulting rebound enables the roll hardness tester to determine the strength of the concrete.

- Nominal kinetic energy: 4.5 J
- For high-strength concrete
- Simple and quick operation
- For determining concrete hardness
- Schmidt principle

PCE-950-ICA is a handheld material hardness tester used to determine the hardness of 10 different types of metal (i.e., cast steel, hammered steel, cold-rolled steel, stainless steel, cast iron, ductile iron, aluminum alloy, brass, bronze and forged copper alloy) according to the Leeb rebound method. In addition to Leeb hardness units, the metal hardness tester displays hardness measurements in Rockwell C, Rockwell B, Rockwell A, Brinell, Vickers and Shore hardness units.

- Measurement ranges: 19.8-68.5 HRC / 13.5-101.7 HRB / 59.1-85.8 HRA / 19-655 HB / 80-976 HV / 32.2-115 HS 
- Hardness units: HL, HRC, HRB, HRA, HB, HV, HS
- Accuracy: 2% / Repeatability: 2%
- Impact device: Type D (integrated)
- Data Analysis Software
- For use with hammered steel, cold-rolled steel, stainless steel, cast iron, ductile iron, aluminum alloy, brass, bronze and forged copper alloy metals
- Includes ISO calibration certificate

The Metal Hardness Testing Durometer PCE-2600N is used wherever a fast hardness test has to be carried out. It is possible to use the durometer PCE-2600N to determine the surface hardness of many metals. The durometer PCE-2600N is especially suitable for quality or product inspection.

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.8%
- Impactor: DL
- Display: 128 x 64 OLED

Due to its compact design, the PCE-2550 hardness tester is easy to use for incoming and outgoing inspections. Due to the adjustable hardness scales, the hardness tester PCE-2550 is very versatile.

- Measuring ranges: 170 ... 960 HLD
- Measurement direction: 360°
- Impact device: Type D
- Measurement units: HL, HB, HRB, HRC, HRA, HV, HS
- Internal measurement memory

The PCE-DDA 10 shore Material Tester is an ergonomic device to check Shore hardness in gum, plastic and other non-metallic materials. It has been designed with a very high quality. The PCE-DDA 10 Material Tester is mainly used for soft gums, elastomers, natural rubber, neoprenes, casting resin, white PVC, leather, etc. It has a reading accuracy of 0.1 hardness units.

- Handheld device
- For Shore A measurements
- Single and Serial Measurements
- Data transfer to pc
- Incl. ISO Calibration Certificate

The portable and easy-to-use surface testing - roughness tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The roughness tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface
- Incl. ISO calibration certificate

Mechanical shore hardness tester for measuring hardness of soft elastomer with drag needle. The shore hardness tester is composed of a single component with a measuring head and a 360º dial. To improve the readability of peak value, the device comes with a drag needle, that ensures the maximum reading can be captured. Once it has been measured, it can be reset to zero. 

- Force of pressure: 0 to 12.5 N
- Penetrating body: 35º (according to Shore A)
- Equipped with drag needle
- Measurement range: 10 ... 90
  (pressure diminishes below 10 and above 90)
- Margin of error: ± 1
- Division of scale: 1
- incl. ISO Calibration Certificate

- Measuring range: 0 ... 1250 µm
- Accuracy: ± (1% + 1 µm)
- Resolution: 0.1 µm (<99.9 µm), 1 µm (> 100 µm)
- Measurement data storage for up to 500 data
- Data transfer via Wifi and USB
- Two different probes for NFe and Fe (included)
- incl. ISO Calibration Certificate

The PCE-TG 300-P5EE is an ultrasonic thickness tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the ultrasonic thickness tester. Wall thicknesses under a coating can also be measured with the ultrasonic thickness tester.

- Measuring range: P-E: 2 ... 600 mm / 0.07 ... 23.62", E-E: 2.5 ... 100 mm / 0.09 ...3.93"
- Diameter: 10mm / 0.39"
- Minimum diameter of pipes: 20 x 3 mm / 0.787 ... 0.118"
- Frequency: 5MHz
- Bluetooth
- incl. ISO calibration certificate