£ 266.00
Price excl. VAT &. delivery
2 year Warranty
2 year Warranty
The material thickness tester is used for the quick and precise detection of layer thicknesses on metals. In comparison to many other thickness meters, this material thickness tester does not have to differentiate between ferrous and non-ferrous metal.
The material thickness meter for cars is for measuring the thickness of paint and plastic on ferrous or non-ferrous metals without damaging the coating's surface. The material thickness meter stands out due to its high range of measurement.
- Measurement range: 0 ... 1250 µm / 49.2 mils
- Resolution: 0.1 µm / 0.004 mils (in a range of 0.0 µm ... 99.9 µm / 3.9
mils) 1 µm / 0.04 mils (above the range)
- Accuracy: ± 2% or 2.5 µm / 0.1 mils (highest reading is valid)
- Display: LCD with 4 mm x 10 mm (0.2 in x 0.4 in) high digits
The PCE-DDA 10 shore Material Tester is an ergonomic device to check Shore hardness in gum, plastic and other non-metallic materials. It has been designed with a very high quality. The PCE-DDA 10 Material Tester is mainly used for soft gums, elastomers, natural rubber, neoprenes, casting resin, white PVC, leather, etc. It has a reading accuracy of 0.1 hardness units.
- Handheld device
- For Shore A measurements
- Single and Serial Measurements
- Data transfer to pc
- Incl. ISO Calibration Certificate
The PCE-DDD 10 shore Material Tester is an ergonomic device to check Shore D hardness in materials such as hard rubber and thermoplastic. It has been designed with a very high quality.
- Handheld device
- For Shore D measurements
- Single and Serial measurements
- Data transfer to PC
- Incl. ISO Calibration Certificate
The PCE-DDD 10 Shore D Material Tester is a portable handheld device used to check Shore D hardness in hard rubber and thermoplastic. This digital Material Tester has a reading accuracy of 0.1 hardness units. The Material Tester comes manufacturer calibrated and can be optionally certified to ISO standards for an additional fee (see accessories for details).
- Portable handheld digital device
- For Shore D hardness testing
- Single and serial measurements
- Data transfer to PC
The PCE-DDA 10 Shore A Material Tester is a portable handheld device used to check Shore A hardness in soft gums, elastomers, natural rubber, neoprenes, casting resin, white PVC, leather, etc. This digital Material Tester has a reading accuracy of 0.1 hardness units. The Material Tester comes manufacturer calibrated and can be optionally certified to ISO standards for an additional fee (see accessories for details).
- Portable handheld digital device
- For Shore A hardness testing
- Single and serial measurements
- Data transfer to PC
The PCE-TG 300-NO5/90 is a thickness meter for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the thickness meter. Wall thicknesses under a coating can also be measured with the thickness meter.
- Measuring range: 1 ... 600 mm / 0.039 ... 23.62" (steel)
- Diameter: 10mm / 0.39"
- Sensor at 90° angle
- Minimum diameter of pipes: 20 x 3 mm / 0.787 ... 0.118"
- Frequency: 5 MHz
- Bluetooth
PCE-5000 is a portable hardness tester that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys with a minimum thickness of 2 mm / .08 in. Non-destructive testing produces microscopic indentation.
- Measurement according to ASTM A1038 ultrasonic contact impedance (UCI) method
- Measurement units: Rockwell A (HRA), Rockwell B (HRB), Rockwell C (HRC), Brinell (HB), Vickers (HV) and MPa (N/mm²) SI units
- Measurement ranges: 61-85.6 HRA, 41-100 HRB, 20.3-68 HRC, 85-650 HB, 50-999 HV, 255-2180 MPa (N/mm²)
- Accuracy: ± 1.5 HR, ± 3% HB, ± 3% HV, Repeatability: ± 0.3%
- Memory size: 1,000 groups for measurement data and 20 groups for calibration data
- Different probe types (also automatic motorized probes) available
