PCE-HT 225E is a material test hammer, also called a concrete rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² / 1450.38 ... 8702.26 psi
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- Data processing software included

 

- Measuring range: Fe: 0 ... 500 µm, NFe: 0 ... 500 µm
- Accuracy after foil calibration: ±(1% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"

- Measuring range: 0 ... 1250 µm
- Accuracy: ± (1% + 1 µm)
- Resolution: 0.1 µm (<99.9 µm), 1 µm (> 100 µm)
- Measurement data storage for up to 500 data
- Data transfer via wifi and USB
- Two different probes for NFe and Fe (included)

PCE-CPT 20 is a Material Tester, or surface coating flexibility testing device, used for testing the formability, ductility, adhesion and elongation of paints, lacquers, varnishes, powder and protective coatings on sheet metal. Used in manufacturing production, paint shop and quality control applications, the Material Tester aids in determining coating strength, durability and elasticity.

- Tests surface coatings on metal sheets 0.3 to 1.25 mm thick
- Provides a maximum depression force of 2500 N
- Offers a display resolution of 0.01 mm

 

The material hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The material hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The material hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission

The material surface roughness tester PCE-RT 2000BT is used for accurate measurement of surface roughness. The material tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- Bluetooth
- 3 different cut-off wavelengths
- Download free app from the Google Play Store

- Large measuring range:  Rz: 0.02 μm ... 320 μm; Ra, Rq: 0.005 μm ... 32 μm
- Accuracy of ± 10% and repeat accuracy of ± 6%
- Touchscreen configuration and Android/printer bluetooth connectivity 
- Sensor has diamond test head with 90-degree cone angle
- Optional sensors and extension rod for small holes and curved surfaces 

- Measuring range: Fe: 0 ... 3000 µm, NFe: 0 ... 3000 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

- Measuring range: Fe: 0 ... 2000 µm, NFe: 0 ... 2000 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

- Measuring range: Fe: 0 ... 5000 µm, NFe: 0 ... 3000 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

- Measuring range: Fe: 0 ... 1500 µm, NFe: 0 ... 1500 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO Calibration Certificate

- Measuring range: Fe: 0 ... 2500 µm, NFe: 0 ... 2500 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

- Melting rate: 0.1 to 400.0 g / 10 min
- Heating temperature: 120 ... 400°C / 248 ... 752°F
- Measuring accuracy temperature: ± 0.2°C / 0.36°F
- Resolution: 0.1°C / 0.18°F
- Large 7" TFT touch display
- Already pre-set materials
- Various weights included
- Standards: ISO1133-1997, ASTM 1238-04C, GB / T3682-2000

The material surface roughness tester PCE-RT 2000 is used for accurate measurement of surface roughness. The material tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- 3 different cut-off wavelengths
- PC software

The material tester is an analog measuring device to determine concrete strength. The measuring method of the material tester is based on the Schmidt principle. With this measuring method, a kinetic impact energy hits the concrete from the material tester. The resulting rebound enables the material tester to determine the strength of the concrete.

- Nominal kinetic energy: 4.5 J
- For high-strength concrete
- Simple and quick operation
- For determining concrete hardness
- Schmidt principle

The portable and easy-to-use material tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The material tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface
- Incl. ISO calibration certificate

With this automotive tester, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the automotive tester consists of braided tungsten.

- Diameter: Ø2.2mm / 0.08"
- Cable length: 1m / 3.2 ft
- Camera direction: 90°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

The Ultrasonic Contact Impedance (UCI) durometer PCE-3500 has been designed for the non-destructive hardness measurement of metallic components. A 136° Vickers diamond at the probe is stimulated with its self-resonance to allow the user to very accurately measure hardness of small items, thin-walled items (>1 mm), and surface-hardened layers. Small imprint after measuring for mirrored surfaces.

- Probe is 50 Newtons / 11.2 lbf force, 10 and 98 N probes are options
- Tests HRC, HRB, HV, HB, MPa
- Memory function via SD card and included PC software
- Large color LCD display with back lighting