The PCE-830-2 Current Clamp is used for measuring one to three phases of electrical quantities for alternating current (AC). This Current Clamp also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

The Xgard-1-PH3 is a single-gas Gas Leak Detector used to warn for gases (Phosphine, PH₃, 0 ... 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Phosphine, PH₃, 0 ... 1 ppm)
- Additional display and alarm station
- ATEX or UL approval

The easy-to-use PCE-PA 8300 Three Phase Power Data Logger is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 2) 30 A ... 3000 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

The Gas Leak Detector AQ-300 Set EF is a high-precision measuring device for measuring the formaldehyde concentration in our circulating air.

- Range Formaldehyde: 0...10 ppm
- High accuracy and functionality
- Alarm function: "High", "Low", Mute
- Alarm output: Transistor output, 150-mA max
- Low Alarm, High Alarm & Control
- Analog output: 0... 5V
- Location ID: Storage of the measuring location

The Gasmaster GM-1 gas leak detector is a reliable, stationary warning device for gases. To connect a gas sensor, the gas measuring device is optionally supplied with a 4 - 20 mA or an mV signal input. The signal input has two alarm relays with which the gas leak detector can control signal lamps/horns or fans, for example.

- 1 input for a gas sensor
- Adaptation of gas sensors: O2, O3, CO, CO2, NH3, H2S
- Various combinations possible
- Event logging
- Large, backlit LCD display
- A/V alarm device max. 24V DC 650 mA
- Gas sensors optional

The Xgard-1-NO2 is a single-gas gas sensor used to warn for gases (Nitrogen dioxide, NO₂, 0 ... 10 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Nitrogen dioxide, NO₂, 0 ... 10 ppm)
- Additional display and alarm station
- ATEX or UL approval

This Carbon Dioxide Meter Gas-Pro-2 can gauge with its sensors a maximum of five different gases. Because of this versatility, the Carbon Dioxide Meter Gas-Pro-2 is ideal for use in a variety of applications, such as near canals, sewage treatment plants, drains, wastewater facilities, dumps and landfills, chemical and oil plants, shipping ports and more.

- Purpose: Personal protection
- Sensor type: CO / H2S / O2 / CH4
- Memory: Yes
- Interface: USB
- Includes suction pump
- Other gas sensors available upon request. (Please email jmu@pce-instruments.com (UK) or jwe@pce-instruments.com (US) for details!)

Gas Detector AQ-500 is a highly accurate instrument for measuring ozone concentrations in the air. The Gas Detector can be equipped with four different heads that vary in their measurement range.

- High accuracy and functionality
- Interchangeable sensor heads!
- Battery operation
- Sensor head OZU included in delivery (Ozone 0-0.15 ppm)
- Alarm function
- Data logger

 

The Xgard-1-SO2 is a single-gas Gassensor used to warn for gases (Sulfur Dioxide, SO₂, 0 ... 10 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Sulfur Dioxide, SO₂, 0 ... 10 ppm)
- Additional display and alarm station
- ATEX or UL approval

The Xgard-1-PH3 is a single-gas Gassensor used to warn for gases (Phosphine, PH₃, 0 ... 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Phosphine, PH₃, 0 ... 1 ppm)
- Additional display and alarm station
- ATEX or UL approval

Gas Leak Detector AQ-500 is a highly accurate instrument for measuring ozone concentrations in the air. The Gas Leak Detector can be equipped with four different heads that vary in their measurement range.

- High accuracy and functionality
- Interchangeable sensor heads!
- Battery operation
- Sensor head EOZ included in delivery (Ozone 0-10 ppm)
- Alarm function
- Data logger

The HVACR Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This HVACR Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.2 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 x 97 x 46 mm / 9.6 x 3.8 x 1.8 in
- Incl. ISO calibration certificate

Triple Plus+ is the latest generation of the respected "Triple" family of toxic, oxygen and flammable gas detectors. Intrinsically safe, the Triple Plus+ provides enhanced features for safety and detector fleet managers including:

- Selection of flammable gas correction factors (so one unit can be used in
  several locations across a site)
- Annotation of the data file with user names and site names selected from
  pre-configured files in the unit

* Call to order or see accessories tab. Must specify sensors (see chart for details) and choose with / without internal pump. Charger and software sold separately.

 

Measuring function
- Temperature: -30 ... 65°C / -22 ... 149°F (Internal)
                          -40 ... 125°C / -40 ... 257°F (external)
- Humidity: 0 ... 100% RH (Internal & External)
- Memory for 25,920 readings
- Saves as PDF

The Xgard-1-CL2 is a single-gas sas detector used to warn for gases (Chlorine, CL₂, 0 ... 5 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Chlorine, CL₂, 0 ... 5 ppm)
- Additional display and alarm station
- ATEX or UL approval

 

Gas Detector AQ-500 is a highly accurate instrument for measuring ozone concentrations in the air. The Gas Detector can be equipped with four different heads that vary in their measurement range.

- High accuracy and functionality
- Interchangeable sensor heads!
- Battery operation
- Sensor head OZL included in delivery (0-0.5 ppm)
- Alarm function
- Data logger

 

The Gas Leak Detector AQ-500 Set EF is a high-precision measuring device for measuring the formaldehyde concentration in our circulating air.

- Range Formaldehyde: 0...10 ppm
- High accuracy and functionality
- Digital output: RS232 with USB converter
- Data Logger: 8188 values
- PC transfer: Software and data cable included

The Xgard-1-CL2 is a single-gas Gas Leak Detector used to warn for gases (Chlorine, CL₂, 0 ... 5 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

- Stationary
- For (Chlorine, CL₂, 0 ... 5 ppm)
- Additional display and alarm station
- ATEX or UL approval