The PCE-830 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

The ultrasonic flow tester is required as part of a control measurement or to quickly determine the flow in a pipeline and is a portable / easy-to-install measuring system. The ultrasonic flow tester works according to the transit time difference method. The measuring principle of the flow tester is quite simple.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe sizes: 50 … 720 mm (approx. 1.9 … 28")
                      20 …108 mm (approx. 0.8 … 4.2")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, Z
- Incl. sensors TDS-HM and TDS-HS on rails

The PCE-830-3 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-3007 flexible amp clamp (3000 A)
- Electrical conductor pick-up: 170 mm / 6.69 in diameter
- Length of electrical conductor: 610 mm / 24.0 in
- Dimensions: 257 mm x 155 mm x 57 mm / 10.1 in x 6.1 in x 2.2 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values - single phase)

The PCE-830-3 Electrical Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Electrical Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-3007 flexible amp clamp (3000 A)
- Electrical conductor pick-up: 170 mm / 6.69 in diameter
- Length of electrical conductor: 610 mm / 24.0 in
- Dimensions: 257 mm x 155 mm x 57 mm / 10.1 in x 6.1 in x 2.2 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values - single phase)

Due to its compact design, the PCE-2550 material tester is very easy to use for incoming and outgoing inspections. Due to the adjustable hardness scales, the material tester PCE-2550 is versatile.

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.4%, Repeatability: ± 0.6%
- Impact Device: Type D
- Measuring Direction: 360°
- Internal measured value memory

The automotive tester / borescope with side view camera gives you new, visual insights into the interior of motors and systems. The automotive tester / borescope with side view camera is the ideal tool for maintenance and repair in workshops or industrial companies. Optical analysis with an automotive tester / borescope has never been so easy.

- Cable length:  2000 mm, 6.56 ft
- Cable diameter:  3 mm, 0.11"
- Camera resolution / image sensor: 400 x 400 Px
- Cable type: flexible
- Video output: HDMI
- Side view camera
- LED light

The two-way optics is a great advantage of the PCE-VE 1014N-F automotive tester or inspection camera. There is easy control of the camera head with the automotive tester. The automotive tester allows you to capture images and videos, and the videos are also stored with an audio recording. 

- Cable length: 1.5 m / 4.9 ft
- Camera head: 2-way
- Diameter: 4.5 mm / 0.18 in
- Resolution: 640 x 480 Pixel
- Storage of pictures and videos
- 8 GB memory card incl.
- LED lighting

The easy-to-use PCE-PA 8300 Clamp-On Tester is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 2) 30 A ... 3000 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

The PCE-830 Electrical Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Electrical Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

The easy-to-use PCE-PA 8300 Electrical Tester is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 2) 30 A ... 3000 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

The portable and easy-to-use material tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The material tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface

The easy-to-use PCE-PA 8300 Clamp-On Tester is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 1) 20 A ... 1200 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

The automotive tester PCE-VE 355N3 is a two-way articulating videoscope, inspection camera, industrial endoscope or borescope for the non-destructive inspection (NDI) of small components and hard-to-reach places. The camera head features 5 LED lights with automatic illumination. Pictures and videos are saved to the included 8 GB SD card memory, allowing easy transfer to a PC.

- 2-way camera probe
- Diameter camera head: Ø 4.5mm / 0.18"
- Interface: Mini-USB 1.1 und AV out/in
- Memory: 8 GB SD memory card (incl.)
- Cable length: 3 m /  9ft 10"

- incl. ISO-Calibration Certificate

The roughness tester PCE-RT 2000BT is used for accurate measurement of surface roughness. The roughness tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- Bluetooth
- 3 different cut-off wavelengths
- Download free app from the Google Play Store

The portable and easy-to-use roughness tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The roughness tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface

The easy-to-use PCE-PA 8300 Electrical Tester is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 1) 20 A ... 1200 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage