- Measuring ranges
   Air humidity: 0 ... 100% RH
   Absolute humidity: 0 ... 500 g/m³
   Temperature: -30 ... 100°C / -22 ... 212°F
   Dew point temperature: -30 ... 100°C / -22 ... 212°F
   Wet bulb temperature: 0 ... 80°C / 32 ... 176°F
- Accuracy
   Humidity: ± 2% (40 ... 60% RH)
   Temperature: ± 0.5°C / 0.9°F (20 ... 60°C / 68 ... 140°F)
- HOLD and extreme value display
- Including sinter filter
- Including ISO Calibration Certificate

The environmental tester PCE-228HTE is a mobile device for measuring pH, mV, °C and °F, complete with SD card memory and an RS-232 interface. This particular model includes a special pH electrode suitable for temperatures up to 100°C / 212°F.

- Measurement range: 0.00 ... 14.00 pH
- Resolution: 0.01 pH
- Accuracy: ±(0.02 pH + 2 digits)
- Memory: flexible via SD card memory 1 ... 16 GB
- Interface: RS-232
- Incl. special pH electrode: for temperatures to 100°C / 212°F
- Incl. ISO Calibration Certificate

Without a doubt, the main advantage of this handheld cup vane environmental tester is that it doesn't need to be held exactly in the direction of the wind. Environmental tester with impellers typically have to be held exactly in the direction of the air flow to take accurate measurements. Digital cup vane environmental tester, wind direction will not influence the measurement.

- 0.9 to 35.0 m/s
- 2.5 to 126.0 km/h
- 1.4 to 68.0 knots
- 1.6 to 78.2 miles/h 
- incl. ISO Calibration Certificate

 

Without a doubt, the main advantage of this handheld cup vane environmental tester is that it doesn't need to be held exactly in the direction of the wind. Environmental tester with impellers typically have to be held exactly in the direction of the air flow to take accurate measurements. Digital cup vane environmental tester, wind direction will not influence the measurement.

- 0.9 to 35.0 m/s
- 2.5 to 126.0 km/h
- 1.4 to 68.0 knots
- 1.6 to 78.2 miles/h 

 

The environmental tester measures the flow velocity according to the hot wire principle. This guarantees a particularly compact design. In addition to the flow rate, the environmental tester can measure the volume flow and the ambient temperature.

- Measuring range: 0.3 ... 30.0 m/s / 0.98 ... 98.4 ft/s
- Probe length: 270 … 990 mm / 10.63 … 38.98 / 29.1"
- Probe diameter: Ø0.8 ... 1.2 mm / 0.031 x 0.047"
- Data memory for 960 measured values
- Wind speed
- Volume flow
- Temperature measurement
- incl. ISO Calibration Certificate (wind speed function only)

The environmental tester has a temperature measuring range of -20 ... 60 °C and a humidity measuring range of 0 ... 99.9% RH. The readings from the environmental tester can be read directly on the 2.3" color display.

Temperature measurement
- Measuring range: -20 ... 60 °C / -4 ... 140 °F
Humidity measurement
- Measuring range: 0 ... 99.9% RH
- Data memory for 12800 measuring points
- For mounting on the wall
- WiFi interface
- incl. ISO Calibration Certificate

 

The two-way optics is a great advantage of the PCE-VE 1034N-F automotive tester or inspection camera. There is easy control of the camera head with the automotive tester. The automotive tester allows you to capture images and videos, and the videos are also stored with an audio recording. 

- Cable length: 3 m / 9.84 ft
- Camera head: 2 way
- Diameter: 4.5 mm / 0.18 in
- Resolution: 640 x 480 Pixel
- Storage of pictures and videos
- 8 GB memory card incl.
- LED lighting

The Ultrasonic Contact Impedance (UCI) Metal Hardness Tester PCE-3500 has been designed for the non-destructive hardness measurement of metallic components. A 136° Vickers diamond at the probe is stimulated with its self-resonance to allow the user to very accurately measure hardness of small items, thin-walled items (>1 mm), and surface-hardened layers. Small imprint after measuring for mirrored surfaces.

- Probe is 50 Newtons / 11.2 lbf force, 10 and 98 N probes are options
- Tests HRC, HRB, HV, HB, MPa
- Memory function via SD card and included PC software
- Large color LCD display with back lighting

- Measuring range CO2: 400 ... 5000 ppm
- Measuring range temperature: -10.0 ... 50.0°C / 14 ... 122°F
- Measuring range humidity: 0 ... 99% rh
- Battery operation
- Limit exceeded
- Beep

   ozin², ftH2O, cmH2O, kgcm², bar

The Ultrasonic Contact Impedance (UCI) durometer PCE-3500 has been designed for the non-destructive hardness measurement of metallic components. A 136° Vickers diamond at the probe is stimulated with its self-resonance to allow the user to very accurately measure hardness of small items, thin-walled items (>1 mm), and surface-hardened layers. Small imprint after measuring for mirrored surfaces and nitrided surfaces.

- Probe is 10 Newtons / 2.2 lbf force, 50 and 98 N probes are options
- Tests HRC, HRB, HV, HB, MPa
- Memory function via SD card and included PC software
- Large color LCD display with back lighting

The Ultrasonic Contact Impedance (UCI) durometer PCE-3500 has been designed for the non-destructive hardness measurement of metallic components. A 136° Vickers diamond at the probe is stimulated with its self-resonance to allow the user to very accurately measure hardness of small items, thin-walled items (>1 mm), and surface-hardened layers. Small imprint after measuring for mirrored surfaces and nitrided surfaces.

- Probe is 98 Newtons / 22 lbf force, 10 and 50 N probes are options
- Tests HRC, HRB, HV, HB, MPa
- Memory function via SD card and included PC software
- Large color LCD display with back lighting

The Ultrasonic Contact Impedance (UCI) Metal Hardness Tester PCE-3500 has been designed for the non-destructive hardness measurement of metallic components. A 136° Vickers diamond at the probe is stimulated with its self-resonance to allow the user to very accurately measure hardness of small items, thin-walled items (>1 mm), and surface-hardened layers. Small imprint after measuring for mirrored surfaces and nitrided surfaces.

- Probe is 10 Newtons / 2.2 lbf force, 50 and 98 N probes are options
- Tests HRC, HRB, HV, HB, MPa
- Memory function via SD card and included PC software
- Large color LCD display with back lighting

The Ultrasonic Contact Impedance (UCI) Metal Hardness Tester PCE-3500 has been designed for the non-destructive hardness measurement of metallic components. A 136° Vickers diamond at the probe is stimulated with its self-resonance to allow the user to very accurately measure hardness of small items, thin-walled items (>1 mm), and surface-hardened layers. Small imprint after measuring for mirrored surfaces and nitrided surfaces.

- Probe is 98 Newtons / 22 lbf force, 10 and 50 N probes are options
- Tests HRC, HRB, HV, HB, MPa
- Memory function via SD card and included PC software
- Large color LCD display with back lighting

The Ultrasonic Contact Impedance (UCI) durometer PCE-3500 has been designed for the non-destructive hardness measurement of metallic components. A 136° Vickers diamond at the probe is stimulated with its self-resonance to allow the user to very accurately measure hardness of small items, thin-walled items (>1 mm), and surface-hardened layers. Small imprint after measuring for mirrored surfaces.

- Probe is 50 Newtons / 11.2 lbf force, 10 and 98 N probes are options
- Tests HRC, HRB, HV, HB, MPa
- Memory function via SD card and included PC software
- Large color LCD display with back lighting

 

- Large measuring range:  Rz: 0.02 μm ... 320 μm; Ra, Rq: 0.005 μm ... 32 μm
- Accuracy of ± 10% and repeat accuracy of ± 6%
- Touchscreen configuration and Android/printer bluetooth connectivity 
- Sensor has diamond test head with 90-degree cone angle
- Optional sensors and extension rod for small holes and curved surfaces