The PCE-830-3 Current Clamp is used for measuring one to three phases of electrical quantities for alternating current (AC). This Current Clamp also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

The Electrical Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Electrical Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

- Measuring range: 0 ... 1250 µm
- Accuracy: ± (1% + 1 µm)
- Resolution: 0.1 µm (<99.9 µm), 1 µm (> 100 µm)
- Measurement data storage for up to 500 data
- Data transfer via Wifi and USB
- Two different probes for NFe and Fe (included)
- incl. ISO Calibration Certificate

- Measuring range: 0.00 ... 14.00 pH
- Resolution: 0.01 pH
- Accuracy: ± 0.1 pH
- Temperature compensation up to 50°C / 122°F
- Universal mounting bracket
- Incl. ISO calibration certificate

The portable and easy-to-use profilometer with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The profilometer uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface
- Incl. ISO calibration certificate

- Temperature measuring range: 0.0 … 50.0 °C
- Humidity measuring range: 0.0 ... 99.9% RH
- Connection of up to four external sensors
- Analog 4 ... 20 mA input signal
- Wall mounting
- incl. ISO Calibration Certificate

The vibration recorder has a measuring range of 0 ... 200 m/s² for acceleration. In addition to acceleration, the vibration recorder can also perform speed, displacement, frequency and an ISO 18016-3 measurement.

- Acceleration
- Velocity
- Displacement
- Frequency
- Tachometer    
- Infrared temperature measurement   
- 4 GB data memory
- FFT analysis and wave view of the vibration
- incl. ISO Calibration Certificate

- Measuring range: ± 0.03 ... ± 5 m / s
- Measuring accuracy: ± 1%
  (of the measured value)
- Pipe size: DN 25 ... 1200 mm
- Interface: RS232 & RS485
- Relay output
- incl. ISO Calibration Certificate

The force gage is ideal for mobile tensile measurements, such as those carried out by surveyors. Quality materials are used in the manufacture of the force gage. Despite the high measuring capacity, these materials enable a compact design with a low weight.

- Measurement range: 20,000 kg / 200 kN / 44,092 lb
- Resolution: 10 kg / 100 N / 22 lb
- Minimum load: 200 kg / 440 lb
- Supplied without remote control indicator
- incl. ISO Calibration Certificate

- Measuring range: 0.3 ... 25 μm
- Measurement channel sizes: 0.3, 0.5, 1.0, 3.0, 5.0, 10.0 μm
- Counting efficiency: 50% at 0.3 μm, 100% at > 0.45 μm according to JIS
- CO2 Sensor: 0 ... 5000 ppm
- PID Sensor: 0 ... 50 ppm
- Ethernet, USB
- Includes temperature and humidity sensor
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

The force gauge is ideal for mobile tensile measurements, such as those carried out by surveyors. Quality materials are used in the manufacture of the force gauge. Despite the high measuring capacity, these materials enable a compact design with a low weight.

- Measurement range: 20,000 kg / 200 kN / 44,092 lb
- Resolution: 10 kg / 100 N / 22 lb
- Minimum load: 200 kg / 440 lb
- Supplied without remote control indicator
- incl. ISO Calibration Certificate

- incl. ISO-calibration certificate

The HVACR Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This HVACR Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

- Accuracy class 1
- GPS function
- A, B, C & Z frequency weighting
- Fast, Slow, Impulse and Peak time weighting
- Statistics function
- 1/1 octave band included
- 1/3 octave band optional
- Incl. Class 1 sound calibrator
- Incl. ISO Calibration Certificate (for sound calibrator)