With this HVAC meter, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the HVAC meter consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Camera resolution 160,000 pixels each
- Viewing angle front camera 120°, side camera 90°
- Focusing distance 5 … 50 mm / 0.19 ... 1.96" each
- Camera head length: 42 mm / 1.6"
- Bending radius at 90° 35 mm / 1.3"
- Live images from both cameras side by side
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

- Function: time measurement
- Input signal: NPN, PNP
- Display range: -199,999 ... 999,999
- Number of outputs: 3
- Voltage supply: 11 ... 36 V DC

- Function: convert frequency to a usable value
- Input signal: NPN, PNP
- Display range: -199,999 ... 999,999
- Number of outputs: 3
- Voltage supply: 11 ... 36 V DC

- Function: time measurement
- Input signal: NPN, PNP
- Display range: -199,999 ... 999,999
- Number of outputs: 3
- Voltage supply: 85 ... 265 V AC / 120 ... 370 V DC

- Measuring range: 0.3 ... 25 μm
- Measurement channel sizes: 0.3, 0.5, 1.0, 3.0, 5.0, 10.0 μm
- Counting efficiency: 50% at 0.3 μm, 100% at > 0.45 μm according to JIS
- CO2 Sensor: 0 ... 5000 ppm
- Ethernet, USB
- Includes temperature and humidity sensor
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

Single-Gas Gas Leak Detector warning for gases (for Carbon Dioxide CO₂), / without display / with signal output for sensors in combination with a stationary equipment to detect gases (with ATEX approval).

- Stationary
- For Carbon Dioxide CO₂
- Additional display and alarm station
- ATEX approved

 

Single-Gas Gas Detector warning for gases (for Carbon Dioxide CO₂), / without display / with signal output for sensors in combination with a stationary equipment to detect gases (with ATEX approval).

- Stationary
- For Carbon Dioxide CO₂
- Additional display and alarm station
- ATEX approved

 

With this HVAC meter, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the HVAC meter consists of braided tungsten.

- Diameter: Ø2.8mm / 0.11"
- Cable length: 2m / 6.5 ft
- Camera direction: 0°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

With this HVAC meter, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the HVAC meter consists of braided tungsten.

- Diameter: Ø6mm / 0.23"
- Cable length: 5m / 16.4 ft
- Camera direction: 0°
- Resolution: 1MP
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

- Function: convert analog signal into usable value
- Input signal: 4 ... 20 mA, ±20 mA DC, 0 ... 10 V DC, ±10 V DC
- Display range: -1999 ... 9999
- Digit height: 60 mm / 2.3"
- Number of outputs: 2
- Voltage supply: 11 ... 36 V DC

- Signal input range: 0 ... 20 mV
- Units: g, mN, mlb, Pa, kg, N, Ib, kPa, t, kN, klb, MPa
- For load cells, force sensors, etc.
- Up to 1600 Hz sampling rate
- LCD display

- Measuring range: 0.5 ... 75 μm
- Measuring channel sizes: 0.5, 1.0, 2.5, 5.0, 10.0, 30.0 μm
- Counting efficiency: 50% at 0.5 μm 100% at > 0.75 μm according to JIS
- ISO 14644-1, EU GMP Annex I, FS 209E
- Mass concentration
- USB
- Incl. temperature and humidity sensor
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

The pressure indicator is suitable for flush sanitary installation. The pressure indicator may represent on its rotatable display pressures up to 40 bar, absolute or relative. The filling of the pressure indicator has a food safe FDA approval. The flush mounting of the pressure indicator can be sterilized.

- To 40 bar / 580 psi
- Relative and absolute pressure measurement
- Max-min function with reset
- 2-line backlit display

The Gas Leak Detector Gasman-CO is a unique gas meter which protects against a specific gas, inflammable or toxic. The Gas Leak Detector warns with a penetrating alarm and an optical signal (useful in case when there are loud noises in the surroundings) of the existence of dangerous gas concentrations and shows on screen the value of the gas measurement. The Gas Leak Detector fulfills all the European and international norms, even ATEX and UL standards.

- Non-rechargeable, 1-year battery
- For CO (Carbon Monoxide)
- Dust and water resistant - IP 65/67
- 0... 500 ppm

 

The pressure indicator has a two-line display. The pressure indicator can represent pressures up to 600 bar, relative or absolute. The parts of the pressure indicator that come in contact with liquids are made of stainless steel.

- Max. 600 bar / 8702 psi
- Rotating display
- Battery operation
- Media: gas, water, fuels and oils
- Print: absolute or relative (user selectable)
- Diaphragm: stainless steel
- Accuracy class: 0.1

 

With this HVAC meter, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the HVAC meter, consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Front camera with resolution: 1,000,000 pixels
- Front camera viewing angle 120°
- Focus 10 … 100 mm / 0.39 … 3.9"
- Movable camera head 46 mm / 1.8" long
- Bending radius approx. 35 mm / 1.3" at 90°
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission

- Function: convert analog signal into usable value
- Input signal: 4 ... 20 mA, ±20 mA DC, 0 ... 10 V DC, ±10 V DC
- Display range: -1999 ... 9999
- Digit height: 60 mm / 2.3"
- Number of outputs: 2
- Voltage supply: 85 ... 265 V AC / 120 ... 370 V DC

This Air Quality Meter Gas-Pro-2 can gauge with its sensors a maximum of five different gases. Because of this versatility, the Air Quality Meter Gas-Pro-2 is ideal for use in a variety of applications, such as near canals, sewage treatment plants, drains, wastewater facilities, dumps and landfills, chemical and oil plants, shipping ports and more.

- Purpose: Personal protection
- Sensor type: CO / H2S / O2 / CH4
- Memory: Yes
- Interface: USB
- Includes suction pump
- Other gas sensors available upon request. (Please email jmu@pce-instruments.com (UK) or jwe@pce-instruments.com (US) for details!)