The portable and easy-to-use material tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The material tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface

The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission

 

- Measuring range up to 10000 ppm
- Audible alarm with 85 dB
- Rechargeable battery for mobile use
- Automatic calibration
- For the detection of combustible gases

The mobile electrical tester Easycount-3-32-A is an energy meter, installed in a splash-proof and impact-resistant housing, for three-phase current up to 400 V. The approx. 50 cm / 19.6" long cable ends of the mobile electrical tester are equipped with a CEE plug and a CEE coupling.

- Display: 6+1 roller counter
- Resolution: 0.1 kWh
- Degree of protection meter: IP 54
- Counter calibrated

The PCE-TG 300-HT5 is a paint thickness tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the paint thickness tester. Wall thicknesses under a coating can also be measured with the paint thickness tester.

- Measuring range: 1 ... 600 mm / 0.039 ... 23.62" (steel)
- Diameter: 12mm / 0.47"
- Minimum diameter of pipes: 30 mm / 1.18"
- Frequency: 5MHz
- Bluetooth

The ultrasonic flow tester is required as part of a control measurement or to quickly determine the flow in a pipeline and is a portable / easy-to-install measuring system. The ultrasonic flow tester works according to the transit time difference method. The measuring principle of the flow tester is quite simple.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe sizes: 50 … 720 mm (approx. 1.9 … 28")
                      20 …108 mm (approx. 0.8 … 4.2")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, Z
- Incl. sensors TDS-HM and TDS-HS on rails

PCE-EM 30 is a digital portable 3-axis environmental electromagnetic radiation tester or EMF detector used to measure electromagnetic radiation generated by electronic devices and electric installations. This triple-axis EMF meter provides greater precision than single-axis models as well as affords the ability to assess EMFs from more than one source at a time.

- Measuring range: 0 to 199.99 V/m, 0 to 99.999 W/m², 0 to 9.9999 mW/cm²
- EMF bandwidth: 100 kHz to 3 GHz
- Measures EMF of 5G cellular Low-band and Mid-band
- Comes with two external sensor probes (for low and high frequency ranges)

 

The portable and easy-to-use roughness tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The roughness tester uses a DSP chip for control and data processing at high speed and low energy consumption.

- 21 measurement parameters:
   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,
   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),
   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
- Large graphic OLED display
- Memory: 20 measurement histories with all parameters
- USB interface

PCE-PA 8000 is a portable handheld Clamp on Tester used for the testing and inspection of 3-phase / 4-wire, 3-phase / 3-wire, 1-phase / 2-wire and 1-phase / 3-wire electrical circuits. This handy power quality analyzer not only measures multiple electrical properties in real time, but also saves the measurement data in .xls format to the included SD card memory for quick and easy data transfer and analysis using Microsoft Excel.

- True RMS measurement for ACA, ACV
- True power: W, KW, MW
- VA, KVA, MVA, VAR, KVAR, MVAR
- PF (power factor), phase angle (Φ)
- KWH, KVAH, KVARH, PFH
- Voltage measurement range: 10 ... 600 ACV
- Current measurement range: 0.2 ... 1200 ACA
- Real-time current, voltage and power consumption measurement
- Built-in data recorder with adjustable sample rate: 2 ... 7,200 sec.
- Incl. ISO Calibration Certificate

PCE-HT 225E is a hardness test hammer, also called a concrete rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² / 1450.38 ... 8702.26 psi
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- Data processing software included

 

PCE-HT 225E is a material test hammer, also called a concrete rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

- Test range: 10 ... 60 MPa or 100 ... 600 kg/cm² / 1450.38 ... 8702.26 psi
- Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
- Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
- Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
- Data processing software included

 

Measuring function
- DC DC
- AC voltage AC (TRMS)
- AC + DC TRMS voltage
- DC DC
- AC AC (TRMS)
- 4 ... 20-mA %
- AC AC / Rogowski coil
- Resistance
- Frequency
- Duty cycle
- Capacity
- Temperature / thermocouple

The Material Tester PCE-RT 11 is a portable measuring instrument for determination of surface roughness according to Ra, Rz, Rq and Rt in just one device.

- Measures Ra, Rz, Rq and Rt in both Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.05 µm … 10 µm / 0.002 µinch … 394 µinch measurement range
- Rz, Rt: 0.1 µm … 50 µm / 0.004 µinch …1968 µinch measurement range
- Robust Piezoelectric sensor
- Accuracy: ± 15% and Repeatability < 12
- Built-in rechargeable li-ion battery

 

- Measuring width: 0 ... 999,999 RLU
- Fast hygiene tests in just 10 seconds
- USB and Bluetooth printer interface
- Automatic calibration
- For HACCP implementation
- Data storage
- Enables rapid detection of bacterial or microbial residue
- Incl. 100 Test tubes (swabs)

The mobile electrical tester Easycount-3-16-A is an energy meter, installed in a splash-proof and impact-resistant housing, for three-phase current up to 400 V. The approx. 50 cm / 19.6" long cable ends of the mobile electrical tester are equipped with a CEE plug and a CEE coupling.

- Display: 6+1 roller counter
- Resolution: 0.1 kWh
- Degree of protection meter: IP 54

The roughness tester PCE-RT 2000 is used for accurate measurement of surface roughness. The roughness tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- 3 different cut-off wavelengths
- PC software