The PCE-830-3 Data Logging Instrument is used for measuring one to three phases of electrical quantities for alternating current (AC). This Data Logging Instrument also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

- PCE-830 + PCE-3007 flexible amp clamp (3000A)
- Electrical conductor pick-up: 170 mm / 6.7 in diameter
- Minimum radial curve: 35 mm / 1.4 in
- Length of electrical conductor: 610 mm / 24 in
- Sampling rate: 2 sec.
- Memory size: 512 kB / max. 52,420 data (1 phase)
- Incl. ISO calibration certificate

- Measuring range: Fe: 0 ... 2000 µm, NFe: 0 ... 2000 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

- Measuring range: Fe: 0 ... 1500 µm, NFe: 0 ... 1500 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO Calibration Certificate

- Measuring range: Fe: 0 ... 2500 µm, NFe: 0 ... 2500 µm
- Accuracy after foil calibration: ±(2% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO-Calibration Certificate

The material hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The material hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The material hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission
- Incl. ISO Calibration Certificate

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

- Measuring range: 10 ... 999.9 V
- AC voltage AC
- Alternating current AC
- Active power
- Power factor
- Phase angle
- Frequency
- Harmonic measurement
- Data memory: 512 kB 
  (non-volatile memory)
- incl. 4 current clamps / tapping terminals
- Standards: IP 30 / IEC 61 010, 600 V / CAT III
- incl. ISO Calibration Certificate 
- incl. ISO Calibration Certificate 

The Material Tester PCE-RT 11-ICA is a portable measuring instrument for determination of surface roughness according to Ra, Rz, Rq and Rt in just one device.

- Measures Ra, Rz, Rq and Rt in both Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.05 µm … 10 µm / 0.002 µinch … 394 µinch measurement range
- Rz, Rt: 0.1 µm … 50 µm / 0.004 µinch …1968 µinch measurement range
- Robust Piezoelectric sensor
- Accuracy: ± 15% and Repeatability < 12%
- Built-in rechargeable li-ion battery
- Inc. ISO Calibration Certificate

The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission
- Incl. ISO Calibration Certificate

The hardness tester PCE-2900 has been developed for hardness measurements on metallic materials. The hardness tester PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The hardness tester PCE-2900 measures the hardness according to the Leeb rebound principle. 

- Measurement according to Leeb Rebound method
- Measurement units: HLD, HRA, HRB, HRC, HB, HV, HS
- Measurement ranges: 170-960 HLD, 59.1-88 HRA, 3.5-101.7 HRB, 17.9-69.5 HRC, 19-683 HB, 80-1042 HV, 30.6-102.6 HS 
- Accuracy: ± 0.5%, Repeatability: ± 0.6%
- Impactor: Type D
- USB and WiFi for data transmission
- Incl. ISO Calibration Certificate

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

- Measuring range: 10 ... 999.9 V
- AC voltage AC
- Alternating current AC
- Active power
- Power factor
- Phase angle
- Frequency
- Harmonic measurement
- Data memory: 512 kB 
  (non-volatile memory)
- incl. 4 current clamps / tapping terminals
- Standards: IP 30 / IEC 61 010, 600 V / CAT III
- incl. ISO Calibration Certificate 

The Roughness Tester PCE-RT 11-ICA is a portable measuring instrument for determination of surface roughness according to Ra, Rz, Rq and Rt in just one device. The small roughness tester is especially designed for fast measuring of roughness.

- Measures Ra, Rz, Rq and Rt in both Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.05 µm … 10 µm / 0.002 µinch … 394 µinch measurement range
- Rz, Rt: 0.1 µm … 50 µm / 0.004 µinch …1968 µinch measurement range
- Robust Piezoelectric sensor
- Accuracy: ± 15% and Repeatability < 12%
- Built-in rechargeable li-ion battery
- Inc. ISO Calibration Certificate

PCE-PA 8000 is a portable handheld Clamp on Tester used for the testing and inspection of 3-phase / 4-wire, 3-phase / 3-wire, 1-phase / 2-wire and 1-phase / 3-wire electrical circuits. This handy power quality analyzer not only measures multiple electrical properties in real time, but also saves the measurement data in .xls format to the included SD card memory for quick and easy data transfer and analysis using Microsoft Excel.

- True RMS measurement for ACA, ACV
- True power: W, KW, MW
- VA, KVA, MVA, VAR, KVAR, MVAR
- PF (power factor), phase angle (Φ)
- KWH, KVAH, KVARH, PFH
- Voltage measurement range: 10 ... 600 ACV
- Current measurement range: 0.2 ... 1200 ACA
- Real-time current, voltage and power consumption measurement
- Built-in data recorder with adjustable sample rate: 2 ... 7,200 sec.
- Incl. ISO Calibration Certificate

The surface tester PCE-RT 2000BT-ICA is used for accurate measurement of surface roughness. The surface tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- Bluetooth
- 3 different cut-off wavelengths
- Download free app from the Google Play Store
- incl. ISO Calibration Certificate

The Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate

PCE-PA 8000 is a portable handheld Electrical Tester used for the testing and inspection of 3-phase / 4-wire, 3-phase / 3-wire, 1-phase / 2-wire and 1-phase / 3-wire electrical circuits. This handy power quality analyzer not only measures multiple electrical properties in real time, but also saves the measurement data in .xls format to the included SD card memory for quick and easy data transfer and analysis using Microsoft Excel.

- True RMS measurement for ACA, ACV
- True power: W, KW, MW
- VA, KVA, MVA, VAR, KVAR, MVAR
- PF (power factor), phase angle (Φ)
- KWH, KVAH, KVARH, PFH
- Voltage measurement range: 10 ... 600 ACV
- Current measurement range: 0.2 ... 1200 ACA
- Real-time current, voltage and power consumption measurement
- Built-in data recorder with adjustable sample rate: 2 ... 7,200 sec.
- Incl. ISO Calibration Certificate

- Measures Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc in both Metric (µm) and Imperial (µinch)
- Ra, Rq, Rc : 0.005 μm…16 μm / 0.197 µinch ... 629.921 µinch measurement range
- Rz, Rt Rp, Rv: 0.020 µm … 200 µm / 0.797 µinch ... 7874.016 µinch measurement range
- Rsm: 5 μm …1000 μm / 1968 µinch … 3937 µinch measurement range
- Rsk: -1 …. 1 measurement range
- Measurement accuracy: <± 10% and Repeatability < 6%
- Robust Piezoelectric sensor
- Saves up to 20 Data points
- 3 different cutoff wavelengths
- Micro USB Interface
- PC Software
- Built-in rechargeable li-ion battery
- Incl. ISO Calibration Certificate

- Measuring range: Fe: 0 ... 500 µm, NFe: 0 ... 500 µm
- Accuracy after foil calibration: ±(1% of reading + 1 µm)
- For many materials such as: iron, steel, aluminum, copper, brass, stainless steel
- Diameter: 17mm / 0.67"
- incl. ISO Calibration Certificate