The PCE-830 Power Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This Power Meter also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

- Measuring range: 0.5 ... 25 μm
- Measurement channel sizes: 0.5, 0.7, 1.0, 3.0, 5.0, 10.0 μm
- Counting efficiency: 50% at 0.5 μm, 100% at > 0.75 μm according to JIS
- Interface: Ethernet, USB
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

- Measuring range: 0.5 ... 25 μm
- Measuring channel sizes: 0.5, 1.0, 5.0 μm
- Counting efficiency: 50% at 0.3 μm 100% at > 0.45 μm according to JIS
- ISO 14644-1, EU GMP Annex I, FS 209E
- Mass concentration
- USB
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

Air flow meter PCE-KWR1 for example for PCE-WL wind logger. Basic wind direction sensor with potentiometer output.

- Output: 0 … 1000 Ohm
- Measurement reading range: 10 … 350 °
- Accuracy: ± 5 °

- Measuring range: 0.3 ... 25 μm
- Measuring channel sizes: 0.3, 0.5, 5.0 μm
- Counting efficiency: 50% at 0.3 μm 100% at > 0.45 μm according to JIS
- ISO 14644-1, EU GMP Annex I, FS 209E
- Mass concentration
- USB
- Incl. calibration certificate traceable to NIST ISO 21501-4 and JIS B9921

The easy-to-use PCE-PA 8300 Power Meter is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 1) 20 A ... 1200 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

The air flow meter PCE-WSAC 50W 24-ICA is primarily used to measure and monitor the wind load on cranes or wind turbines. Furthermore, the wind situation can be measured and analyzed before commissioning a wind turbine. Due to the integrated 4 ... 20-mA analogue output of the air flow meter, the measured data can also be transferred to other controllers for evaluation.

- Measuring range up to 180 km / h
- Input: pulse, analogue (4 ... 20-mA) or radio transmission
- 4 ... 20-mA analog output
- Supply voltage: 24V DC
- Ambient temperature -20 ... 70°C / -4 ... 158°F
- Units adjustable: km / h, mph, m / s 
- Incl. ISO calibration certificate

The easy-to-use PCE-PA 8300 Clamp Meter is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 1) 20 A ... 1200 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

- Measuring range up to 180 km / h
- Input: Pulse, analogue (4 ... 20-mA) or radio transmission
- 4 ... 20-mA analogue output
- Supply voltage: 110 ... 230V AC, 50/60 Hz
- Ambient temperature -20 .. . 70°C / -4 ... 158°F
- Units adjustable: km / h, mph, m / s
- Incl. ISO calibration certificate

The flow meter is required as part of a control measurement or to quickly determine the flow in a pipeline and is a portable / easy-to-install measuring system. The flow meter works according to the transit time difference method. The measuring principle of the flow meter is quite simple.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe sizes: 50 … 720 mm (approx. 1.9 … 28")
                      20 …108 mm (approx. 0.8 … 4.2")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, Z
- Incl. sensors TDS-HM and TDS-HS on rails
- Incl. ISO Calibration Certificate

The Portable Ultrasonic Flow Meter is required as part of a control measurement or to quickly determine the flow in a pipeline and is a portable / easy-to-install measuring system. The Portable Ultrasonic Flow Meter works according to the transit time difference method. The measuring principle of the flow meter is quite simple.

- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s
- Resolution: 0.0001 m/s, 0.00033 ft/s
- Pipe sizes: 50 … 720 mm (approx. 1.9 … 28")
                      20 …108 mm (approx. 0.8 … 4.2")
- Sensor temperature range: 0 ... 160°C / 32 ... 320°F
- Sensor installation: V, Z
- Incl. sensors TDS-HM and TDS-HS on rails

The air flow meter PCE-PDA 10L is a reliable differential pressure gauge for pressure measurement of gases in the range of ±20 kPa. The air flow meter PCE-PDA 10L has many different pressure measuring functions.

- Measuring range: ± 20 kPa  / ± 2.9 psi / ± 0.2 bar
- Resolution: 10 Pa / 0.00145 psi / 0.0001 bar
- Accuracy: ± 0.5% of final value
- Min and Max value memory
- Data logger and leak test
- Temperature measurement, flow measurement
- Pitot tube not included in delivery / optionally selectable