US$ 131.00
ex. VAT, ex. delivery costs
The PCE-DD-A durometer is used to measure Shore A hardness in soft gums, rubber, elastomers and more. This compact pocket sized tester is ideal for checking / testing rubber hardness (tyre condition checker). Calibration is not available for this item.
PCE-DD-D is a Shore D durometer or hardness tester. This Shore D durometer uses an impact rod with a 30º conical point and 50 Newtons (N) of force to make a surface indentation on material samples with a minimum thickness of 6 mm or 0.24". Calibration is not available for this item.
Mechanical shore durometer for measuring hardness of soft elastomer with drag needle. The shore durometer is composed of a single component with a measuring head and a 360º dial. To improve the readability of peak value, the device comes with a drag needle, that ensures the maximum reading can be captured. Once it has been measured, it can be reset to zero.
Mechanical shore durometer for measuring hardness of soft elastomer with drag needle. The shore durometer is composed of a single component with a measuring head and a 360º dial. To improve the readability of peak value, the device comes with a drag needle, that ensures the maximum reading can be captured. Once it has been measured, it can be reset to zero.
The PCE-DDA 10 shore durometer is an ergonomic device to check Shore hardness in gum, plastic and other non-metallic materials. It has been designed with a very high quality. The PCE-DDA 10 durometer is mainly used for soft gums, elastomers, natural rubber, neoprenes, casting resin, white PVC, leather, etc. It has a reading accuracy of 0.1 hardness units.
The PCE-DDD 10 Shore D durometer is a portable handheld device used to check Shore D hardness in hard rubber and thermoplastic. This digital durometer has a reading accuracy of 0.1 hardness units. The durometer comes manufacturer calibrated and can be optionally certified to ISO standards for an additional fee (see accessories for details).
The PCE-DDD 10 shore durometer is an ergonomic device to check Shore D hardness in materials such as hard rubber and thermoplastic. It has been designed with a very high quality.
The PCE-DDO 10 shore durometer is an ergonomic device to check Shore hardness in gum. It has been designed with a high quality. The PCE-DDO 10 durometer is mainly used for soft gums. If the material thickness is not enough, it should be tightened on the back with the same material in order to increase its thickness.
PCE-1000N is a portable handheld Barcol hardness testing durometer used to measure the hardness of pure aluminum, soft aluminum, thick aluminum alloy and aluminum sheets, strips, rods, castings and forgings. The hardness of fiber-reinforced (FRP) plastics, glass-reinforced (GRP) plastics, hard plastics and soft metals (such as copper or lead) also can be tested using this battery-powered digital Barcol impressor hardness meter.
The PCE Instruments PCE-2000N durometer uses the Leeb rebound method. This is a dynamic hardness test method in which a standardized test specimen, usually a hard metal ball, is hit with defined impact energy on a test surface.
PCE-2500N is a portable handheld pen-sized digital material hardness tester, rebound hammer or durometer for use with metals. This high-accuracy hardness tester quickly and accurately measures the surface hardness of 10 common metal materials including steel, cast steel, alloy tool steel, stainless steel, cast iron, ductile iron, cast aluminum alloy, brass, bronze and copper.
PCE-2500N-ICA is a portable handheld pen-sized digital material hardness tester, rebound hammer or durometer for use with metals. This high-accuracy hardness tester quickly and accurately measures the surface hardness of 10 common metal materials including steel, cast steel, alloy tool steel, stainless steel, cast iron, ductile iron, cast aluminum alloy, brass, bronze and copper.
Due to its compact design, the PCE-2550 durometer is very easy to use for incoming and outgoing inspections. Due to the adjustable hardness scales, the durometer PCE-2550 is versatile.
Due to its compact design, the PCE-2550-ICA durometer is easy to use for incoming and outgoing inspections. Due to the adjustable hardness scales, the durometer is very versatile.
The Metal Hardness Testing Durometer PCE-2600N is used wherever a fast hardness test has to be carried out. It is possible to use the durometer PCE-2600N to determine the surface hardness of many metals. The durometer PCE-2600N is especially suitable for quality or product inspection.
The Metal Hardness Testing Durometer PCE-2600N-ICA is used wherever a fast hardness test has to be carried out. It is possible to use the durometer PCE-2600N-ICA to determine the surface hardness of many metals. The durometer PCE-2600N-ICA is especially suitable for quality or product inspection.
The durometer PCE-2900 has been developed for hardness measurements on metallic materials. The durometer PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The durometer PCE-2900 measures the hardness according to the Leeb rebound principle.
The durometer PCE-2900 has been developed for hardness measurements on metallic materials. The durometer PCE-2900 measures the material hardness in Vickers, Brinell, Rockwell, Leeb and Shore. The durometer PCE-2900 measures the hardness according to the Leeb rebound principle.
PCE-5000 is a portable hardness tester or durometer that uses the ASTM A1038 ultrasonic contact impedance (UCI) method to measure the hardness of metals and alloys to measure on a minimum material thickness of 2 mm / .08 in. The test instrument can be mounted on a test stand (as an option) for series measurement in manufacturing process checking. Non-destructive testing produces microscopic indentation.
The Ultrasonic Contact Impedance (UCI) durometer PCE-3500 has been designed for the non-destructive hardness measurement of metallic components. A 136° Vickers diamond at the probe is stimulated with its self-resonance to allow the user to very accurately measure hardness of small items, thin-walled items (>1 mm), and surface-hardened layers. Small imprint after measuring for mirrored surfaces.
The Leeb Metal Hardness Testing Durometer PCE-900 measures the hardness of nine different metals using the Leeb rebound method. This means that with the metal hardness testing durometer a firing pin bounces on a metallic surface and the intensity of the rebound is used as an indicator of the material hardness. The Metal Hardness Testing PCE-900 measures the metal hardness in 6 different hardness scales.
The Metal Hardness Testing Durometer PCE-900-ICA measures the hardness of nine different metals using the Leeb rebound method. This means that with the material hardness tester a firing pin bounces on a metallic surface and the intensity of the rebound is used as an indicator of the material hardness. The Metal Hardness Testing Durometer measures the metal hardness in 6 different hardness scales.
PCE-950 is a handheld metal hardness durometer used to determine the hardness of 10 different types of metal (i.e., cast steel, hammered steel, cold-rolled steel, stainless steel, cast iron, ductile iron, aluminum alloy, brass, bronze and forged copper alloy) according to the Leeb rebound method. In addition to Leeb hardness units, the metal hardness tester displays hardness measurements in Rockwell C, Rockwell B, Rockwell A, Brinell, Vickers and Shore hardness units.
PCE-950-ICA is a handheld metal hardness durometer used to determine the hardness of 10 different types of metal (i.e., cast steel, hammered steel, cold-rolled steel, stainless steel, cast iron, ductile iron, aluminum alloy, brass, bronze and forged copper alloy) according to the Leeb rebound method. In addition to Leeb hardness units, the metal hardness tester displays hardness measurements in Rockwell C, Rockwell B, Rockwell A, Brinell, Vickers and Shore hardness units.
The Durometer is a handy, digital measuring device for measuring tensile and compressive forces. The Durometer offers a sampling rate of 500 Hz and various measurement options such as real-time measurement (RT), maximum value measurement (PEAK), configurable average value acquisition (Average) and automatic measurement storage of up to 100 measurements.
The Durometer is a handy, digital measuring device for measuring tensile and compressive forces. The Durometer offers a sampling rate of 500 Hz and various measurement options such as real-time measurement (RT), maximum value measurement (PEAK), configurable average value acquisition (Average) and automatic measurement storage of up to 100 measurements.
The PCE-DDA 10 Shore A durometer is a portable handheld device used to check Shore A hardness in soft gums, elastomers, natural rubber, neoprenes, casting resin, white PVC, leather, etc. This digital durometer has a reading accuracy of 0.1 hardness units. The durometer comes manufacturer calibrated and can be optionally certified to ISO standards for an additional fee (see accessories for details).
PCE-HT-225A is a heavy-duty concrete hardness tester or concrete test hammer, also called a concrete rebound hammer or Swiss hammer, used to measure surface hardness and material compression strength. Suitable for use with concrete, rock and building materials, this rugged, manufacturer-calibrated rebound hammer is both easy to use and built to last.
The PCE-HT-75 durometer for concrete is easy to use and is fundamentally used in the construction industry as well as other industrial sectors (testing for Wickel hardness of rolls in commodities). This durometer in the form of a hammer device for testing concrete is based on the Swiss principle of measurement.
The durometer is an analog measuring device to determine concrete strength. The measuring method of the concrete durometer is based on the Schmidt principle. With this measuring method, a kinetic impact energy hits the concrete from the durometer. The resulting rebound enables the durometer to determine the strength of the concrete.
PCE-HT 225E is a durometer, also called a concrete rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.
The Ultrasonic Contact Impedance (UCI) durometer PCE-3500 has been designed for the non-destructive hardness measurement of metallic components. A 136° Vickers diamond at the probe is stimulated with its self-resonance to allow the user to very accurately measure hardness of small items, thin-walled items (>1 mm), and surface-hardened layers. Small imprint after measuring for mirrored surfaces and nitrided surfaces.
The Ultrasonic Contact Impedance (UCI) durometer PCE-3500 has been designed for the non-destructive hardness measurement of metallic components. A 136° Vickers diamond at the probe is stimulated with its self-resonance to allow the user to very accurately measure hardness of small items, thin-walled items (>1 mm), and surface-hardened layers. Small imprint after measuring for mirrored surfaces and nitrided surfaces.
The prefix Duro comes from Latin and is usually used when it goes about “hard”. A durometer is therefore a measuring device with which the hardness of materials can be determined. In general, however, only those devices for measuring hardness are called durometers that press a specially shaped indenter onto the test surface with a controlled amount of force. In many standards for hardness testing of plastics and elastomers, the term durometer is used almost universally for the hardness testing devices.
The hardness of a material generally indicates its resistance to penetration by a harder body. In contrast to hardness, strength describes resistance to deformation and separation. While some materials, such as glass, are hard but break easily, for the others, e.g. certain structural steels, the hardness can be used to infer the strength. The harder a material is, the more force is required to deform it. Since the resistance to penetration and the response time of different materials differ greatly due to their structure, various hardness test methods have been developed. For some of the test methods, a durometer is sufficient for hardness measurement, for the other methods several devices are needed. For example, in the case of the methods in which, after the test specimen has been pressed in, the surface of the resulting imprint is determined by measurement under the microscope. One of these methods is the Brinell hardness test, which is described in the EN ISO 6506-1 and ASTM E10-08 standards and was developed especially for metals and metal alloys.
In addition to the tests with high-precision testing devices under the laboratory conditions, test procedures have also become established with which important characteristic values can be tested quickly and easily, even on permanently installed or very large parts, in product development, incoming goods, production and during repeat tests. Many methods differ primarily in the size and shape of the indenter, the amount of force applied and how the effect of the applied force is measured. In order to be able to classify the hardness data correctly, they are marked with the abbreviation of the test method and, if necessary, further information on the test conditions:
As there are so many methods for testing hardness, it is important to ensure that the method used to determine the value is correctly stated when giving the hardness data. For some materials, the measured values of certain frequently used methods can also be given as hardness values according to other methods or as tensile strength due to sufficiently available comparative measurements. For this purpose, the values are read from the material-specific tables or, in the case of the digital durometer, can be output directly via the stored comparative values.
EN ISO 18265 contains conversion tables between Vickers hardness, Brinell hardness. Rockwell hardness and tensile strength for six different metallic materials:
There is also a correlation between the measured values of the frequently used test methods Shore A and Shore D, so that under certain conditions they can also be given as the value of the other quantity.
Many durometers enable fast and uncomplicated measurements of hardness. However, the basic prerequisite is that the model chosen is suitable for the materials and components to be tested. In order to obtain usable data, however, the requirements for the materials to be tested must be met, as well as the specifications for the procedure of the respective measurement and the handling of the device.
Mobile durometers are particularly suitable for testing large or already installed parts. Random samples and parts with suitable dimensions can also be tested with stationary devices or with the durometer fixed on a tripod or test stand. Stationary testing simplifies above all the maintenance of the set-up angle and the spacing of the test points.
Analogue durometers are easy to operate and do not require batteries. They are particularly 
suitable for measurements where no values need to be stored. The models with drag pointer allow easy reading of the maximum value after the measurement. Digital durometers generally show the maximum value of the measurement. However, many types of durometers also allow the maximum, minimum and average values of the measurement series to be retrieved. Models with memory and data interface also facilitate the documentation and further processing on the computer. The more samples need to be tested and documented, the greater the advantages of easy storage and data transfer are. Also the possibility of displaying the measured values as hardness values according to other methods also makes the evaluation of the measurement results much easier. However, it is essential to ensure that the appropriate hardness scales for the material being tested are stored in the durometer.
Basically, it is important to pay attention to the test method when selecting the durometer. VDI/VDE Guideline 2616 provides information on the areas of application and the advantages and disadvantages of the most common methods of hardness testing. The durometers, where the measured value is displayed directly after the measurement, differ mainly in terms of the energy used and the design of the indenter. The harder the material is, the more it can be stressed during the test. Many digital durometers can indicate the hardness as a value according to different methods, but they test only according to one. For the values that are not directly measured, it is important to check whether they may be used for the material being tested. However, some models with an external impact device that work according to the Leeb method can perform different Leeb tests, e.g. according to Leeb C, Leeb D and Leeb G, by using several impact devices.
Often, the scope of delivery already includes suitable calibration plates so that the user can check the measuring accuracy of the durometer himself. Instrument versions with memory are often supplied with a data cable or storage medium. Some models also come with free PC software for evaluating the measurement data. Optional accessories include tripods, test stands or various adapters for mounting on convex or concave surfaces. These facilitate centring and alignment and thus help to avoid measurement errors.
Calibration is the process of checking the accuracy of a measuring instrument. Depending on the measurand, there are different procedures for this. The durometer can be calibrated with the test specimens of the known hardness. With suitable test blocks, the user can thus check the accuracy of his instrument at any time. In some companies there is a requirement for external calibration. Many calibration laboratories offer calibrations according to ISO or DAkkS for durometers and issue calibration certificates for them. When requesting calibration, be sure to specify the method, e.g. Leeb, Rockwell, Barcol, and the numerical values at which your instrument is to be calibrated. If the test values are outside the device-specific accuracy, most durometers can be adjusted, i.e. set back to the specified accuracy.
A durometer is a device for measuring the hardness of materials, especially elastic or rubber-like materials. The calibration of a durometer is important to ensure that it provides accurate and reliable measurements. Here is some information about the calibration of a durometer:
Check the display or the adjustment knob to make sure that the durometer is calibrated to the appropriate scale you want to use.Please note that this is general information on the calibration of a durometer. The exact steps and requirements may vary depending on the manufacturer and model. It is advisable to consult the manufacturer's specific instructions for your durometer.
Calibration is the control of measurement magnitudes correction for a measuring instrument without intervention in the measurement system, or the determination of the systematic display deviation in relation to the real value of the measuring magnitude.
A calibration certificate is a document that confirms that the technical properties of test instruments comply with a recognized standard of measurement.
The introduction of International Standards Organization (ISO) 9000 brought about new requirements for quality control. As a result, many companies and laboratories must obtain ISO calibration certificates for their measuring instruments. An ISO calibration certificate is a controlled document that confirms that the specific test instruments meet the minimum requirements of the appropriate ISO standard. An ISO calibration certificate can be acquired for any shore durometer offered by PCE Instruments.
A durometer calibrator or calibration device must conform to national and international standards such as DIN ISO 7619, ISO 868, ISO 7619 and ASTM D2240. According to these standards, shore durometer readings must be within +/-1 of the point indicated on the scale. To perform correct measurements, a durometer must be calibrated regularly. The period of time between calibrations is called a calibration interval. It is the responsibility of each shore durometer user to determine and check the interval between calibrations. To determine the calibration interval for your durometer, consider the following factors:
PCE Instruments’ friendly and knowledgeable technical experts are available to answer any questions related to the process of establishing a calibration interval. However, as a guideline for best practice, PCE Instruments recommends a calibration interval between 1 and 3 years.
PCE Instruments is a trusted manufacturer and supplier of accurate, reliable shore durometer products. Each test instrument is calibrated and adjusted according to the highest possible quality standards by PCE Instruments itself, or by a first-class calibration laboratory partner. The picture at left shows a sample ISO calibration certificate for a shore durometer.