• Torque: 0.01 ... 100 Nm
• Resolution: 0.01 Nm
• Accuracy: ±2% FS / ±2.5% FS
• Units: Nm, kgf cm, lbf ft, lbf in
• Internal memory: 999 values
• Adjustable alarm

PCE-DD-D is a Shore D durometer or hardness tester. This Shore D hardness tester uses an impact rod with a 30º conical point and 50 Newtons (N) of force to make a surface indentation on material samples with a minimum thickness of 6 mm or 0.24 in. Calibration is not available for this item.

• For Shore D hardness testing of hard rubber, hard resin, acrylic, glass,  thermoplastic and more
• Measurement range: 0 … 100 Shore D
• Accuracy: ± 2 Hardness - Grade

PCE-DD-D is a Shore D durometer or hardness tester. This Shore D durometer uses an impact rod with a 30º conical point and 50 Newtons (N) of force to make a surface indentation on material samples with a minimum thickness of 6 mm or 0.24". Calibration is not available for this item.

• For Shore D hardness testing of hard rubber, hard resin, acrylic, glass,  thermoplastic and more
• Measurement range: 0 … 100 Shore D
• Accuracy: ± 2 Hardness - Grade

PCE-DD-D is a Shore D durometer or hardness tester. This Shore D durometer uses an impact rod with a 30º conical point and 50 Newtons (N) of force to make a surface indentation on material samples with a minimum thickness of 6 mm or 0.24". Calibration is not available for this item.

• For Shore D hardness testing of hard rubber, hard resin, acrylic, glass,  thermoplastic and more
• Measurement range: 0 … 100 Shore D
• Accuracy: ± 2 Hardness - Grade

PCE-DD-D is a Shore D durometer or material hardness tester. This Shore D hardness tester uses an impact rod with a 30º conical point and 50 Newtons (N) of force to make a surface indentation on material samples with a minimum thickness of 6 mm or 0.24". Calibration is not available for this item.

• For Shore D hardness testing of hard rubber, hard resin, acrylic, glass,  thermoplastic and more
• Measurement range: 0 … 100 Shore D
• Accuracy: ± 2 Hardness - Grade

The panel meter is used for the signal processing of 4 .. 20 mA. The panel meter has a 5-digit LED display to allow the user to read the directly measured current values.

• Power supply: 230 V, 110 V, 24 V, 20 … 40 V AC/DC, 85 … 253 V AC/DC (selectable)
• Input signal: 0/4 … 20 mA, 0 … 60 mV, ±60 mV DC, 0 … 10 V, ± 10 V DC (selectable)
• Display: 4 digits, red
• Digit height: 20 mm

• measurement range -4 ... +4 kPa (-40 ... +40 mbar)
• resolution 0.01 kPa
• accuracy: ±1 % FS
• MAX, MIN, AVG value, HOLD
• audible alarm
• 13 selectable pressure units
• USB-C with data transfer
• PC software

The digital temperature indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the digital temperature suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the digital temperature.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers

The process indicator is used for processing 4…20 mA and 0…20 mA signals. Many measuring transducers and sensors use this type of output, which makes the process indicator suitable in a wide application area. The measurement results are shown on the large 5-digit LED-display of the process indicator.

• Input (selectable): 0…20 mA, 4…20 mA, ± 20 mA
• Accuracy: ± (0.2 % FS + 1 dgt.)
• Two open collector outputs
• 24 V power supply sytem for sensors and transducers