The NDT tester or gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60°. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

• Measurement geometry: 60° degree angle
• Measuring range: 0 … 300 GU
• Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
• Light source: D65
• Wave length: 400-700 nm

Due to its compact design, the PCE-2550-ICA metal hardness tester is easy to use for incoming and outgoing inspections. Due to the adjustable hardness scales, the metal hardness tester is very versatile.

• Measuring ranges: 170 … 960 HLD
• Measurement direction: 360°
• Impact device: Type D
• Measurement units: HL, HB, HRB, HRC, HRA, HV, HS
• Internal measurement memory
• incl. ISO Calibration Certificate

PCE-1000N is a portable handheld Barcol hardness tester used to measure the hardness of pure aluminum, soft aluminum, thick aluminum alloy and aluminum sheets, strips, rods, castings and forgings. The hardness of fiber-reinforced (FRP) plastics, glass-reinforced (GRP) plastics, hard plastics and soft metals (such as copper or lead) also can be tested using this battery-powered digital Barcol impressor hardness meter.

• Measurement parameters: Barcol (HBA), Brinell (HB), Vickers (HV), Webster  (HW)  Rockwell (HRB / HRE / HRF / HRH)
• Measuring range: 0 … 100 HBA / 25 … 150 HB
• Accuracy: 81 … 88 HBA: ± 1 HBA / 42 … 48 HBA: ± 2 HBA
• Repeatability: 81 … 88 HBA: ± 1.5 HBA / 42 … 48 HBA: ± 2.5 HBA
• Resolution: 0.1 HBA
• Meets ASTM standards: E140-97; D2583-75; B648-78

The PCE-TG 300-P5EE is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

• Measuring range: P-E: 2 … 600 mm / 0.07 … 23.62", E-E: 2.5 … 100 mm / 0.09 …3.93"
• Diameter: 10mm / 0.39"
• Minimum diameter of pipes: 20 x 3 mm / 0.787 … 0.118"
• Frequency: 5MHz
• Bluetooth

PCE-950 is a handheld metal hardness tester used to determine the hardness of 10 different types of metal (i.e., cast steel, hammered steel, cold-rolled steel, stainless steel, cast iron, ductile iron, aluminum alloy, brass, bronze and forged copper alloy) according to the Leeb rebound method. In addition to Leeb hardness units, the metal hardness tester displays hardness measurements in Rockwell C, Rockwell B, Rockwell A, Brinell, Vickers and Shore hardness units.

• Measurement ranges: 19.8-68.5 HRC / 13.5-101.7 HRB / 59.1-85.8 HRA /19-655 HB / 80-976 HV / 32.2-115 HS 
• Hardness units: HL, HRC, HRB, HRA, HB, HV, HS
• Accuracy: ± 2% / Repeatability: ± 2%
• Impact device: Type D (integrated)
• Data Analysis Software
• For use with hammered steel, cold-rolled steel, stainless steel, cast iron, ductile iron, aluminum alloy, brass, bronze and forged copper alloy metals

This Formaldehyde Meter HFX205-25 is designed to detect formaldehyde in air. The Formaldehyde Meter HFX205-25 shows the formaldehyde-concentration on site and thereby avoids time-consuming and expensive analysis in laboratories. The Formaldehyde Meter HFX205-25 runs with the help of an electromechanical sensor and is designed to determine the current permitted limit. A measurement can be accomplished in less than 30 seconds.

• Range Formaldehyde: 0…25 ppm
• Short reaction time
• Real-time display
• Manual and auto data storage
• High-speed USB
• Software for Online Data transfer

The PCE-TG 300-HT5 is a NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

• Measuring range: 1 … 600 mm / 0.039 … 23.62" (steel)
• Diameter: 12mm / 0.47"
• Minimum diameter of pipes: 30 mm / 1.18"
• Frequency: 5MHz
• Bluetooth