The PCE-830 Clamp Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp Meter also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm / 1.1 in diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
• Sampling rate: 2 sec.
• Memory size: 512 kB (max. 52,000 values (single phase)

The PCE-830 Power Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This Power Meter also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm / 1.1 in diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
• Sampling rate: 2 sec.
• Memory size: 512 kB (max. 52,000 values (single phase)

The easy-to-use PCE-PA 8300 Clamp Meter is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

• Voltage measurement range of 10V … 600V AC
• Current measurement range of (Set 1) 20 A … 1200 A AC
• Performance measurement range of 0 kW … 9.999 MW (VA/VAR)
• Simultaneous display of harmonics and waveform
• Graphic Phasor diagram
• Captures transients including dip, swell, and outage

The easy-to-use PCE-PA 8300 Power Meter is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

• Voltage measurement range of 10 V … 600 V AC
• Current measurement range of (Set 1) 20 A … 1200 A AC
• Performance measurement range of 0 kW … 9.999 MW (VA/VAR)
• Simultaneous display of harmonics and waveform
• Graphic Phasor diagram
• Captures transients including dip, swell, and outage

The PCE-830 HVAC Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This HVAC Meter also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm / 1.1 in diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
• Sampling rate: 2 sec.
• Memory size: 512 kB (max. 52,000 values (single phase)

The easy-to-use PCE-PA 8300 HVAC Meter is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:

• Voltage measurement range of 10 V … 600 V AC
• Current measurement range of (Set 1) 20 A … 1200 A AC
• Performance measurement range of 0 kW … 9.999 MW (VA/VAR)
• Simultaneous display of harmonics and waveform
• Graphic Phasor diagram
• Captures transients including dip, swell, and outage

PCE-WSB 1 is a portable handheld battery-powered whiteness meter used to measure the brightness level of paper, cardboard, cellulose, pulp, textiles, paint, enamel, plastic, porcelain, cement, concrete, building materials, chemicals, powders, talc, starch, flour, salt, detergents, cosmetics and other non-metal substances.

• Measures the whiteness degree of blue light (Wb = R457)
• Meets ISO 2470 and ISO 3688 standards
• Compact, lightweight and user-friendly
• Resolution: 0.1
• Repeat accuracy : ±0.1

The PCE-830 Power Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Power Meter also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 x 62 x 36 mm
• Incl. ISO calibration certificate

The PCE-830 Clamp Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Clamp Meter also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 x 62 x 36 mm
• Incl. ISO calibration certificate

The 3-Phase-Power Meter / 3-Phase Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase-Power Meter / 3-Phase Power Analyzer also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm / 1.1 in diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
• Sampling rate: 2 sec.
• Memory size: 512 kB (max. 52,000 values (single phase)

The color meter PCE-CSM 1 was developed for quality control and offers a very high accuracy. When using the color meter, you can choose between different color spaces (CIE L*a*b*C*h, CIE L*a*b* and CIE XYZ). After a measurement with the color meter, the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the 100 reference values easily. 6 mm aperture for sample scanning.

• CIE L*a*b*C*h, L*a*b* and XYZ
• Automatic white and black calibration
• 8°/d geometry diffused illumination integrating sphere system
• Rechargable Li-ion battery

The PCE-360 is a Single-Phase Power Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

• Measuring range: 10 … 999.9 V
• AC voltage AC
• Alternating current AC
• Active power
• Power factor
• Phase angle
• Frequency
• Harmonic measurement
• Data memory: 512 kB   (non-volatile memory)
• incl. 4 current clamps / tapping terminals
• Standards: IP 30 / IEC 61 010, 600 V / CAT III
• incl. ISO Calibration Certificate

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

• Measuring range: 10 … 999.9 V
• AC voltage AC
• Alternating current AC
• Active power
• Power factor
• Phase angle
• Frequency
• Harmonic measurement
• Data memory: 512 kB   (non-volatile memory)
• incl. 4 current clamps / tapping terminals
• Standards: IP 30 / IEC 61 010, 600 V / CAT III
• incl. ISO Calibration Certificate
• incl. ISO Calibration Certificate

PCE-WSB 1 is a portable handheld battery-powered brightness / whiteness color meter used to measure the brightness level of paper, cardboard, cellulose, pulp, textiles, paint, enamel, plastic, porcelain, cement, concrete, building materials, chemicals, powders, talc, starch, flour, salt, detergents, cosmetics and other non-metal substances.

• Measures the whiteness degree of blue light (Wb = R457)
• Meets ISO 2470 and ISO 3688 standards
• Compact, lightweight and user-friendly
• Resolution: 0.1
• Repeat accuracy : ±0.1

The Ozone Meter Xgard-1-O3 is a single-gas gas sensor used to warn for gases (Ozone, O₃, 0 … 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

• Stationary
• For (Ozone, O₃, 0 … 1 ppm)
• Additional display and alarm station
• ATEX or UL approval

• CIE L*a*b*C*h, L*a*b* and XYZ
• Automatic white and black calibration
• 8°/d geometry diffused illumination integrating sphere system
• Rechargable Li-ion battery
• incl. ISO-Calibration Certificate

PCE-WSB 1 is a portable handheld battery-powered surface testing - brightness / whiteness color meter used to measure the brightness level of paper, cardboard, cellulose, pulp, textiles, paint, enamel, plastic, porcelain, cement, concrete, building materials, chemicals, powders, talc, starch, flour, salt, detergents, cosmetics and other non-metal substances.

• Measures the whiteness degree of blue light (Wb = R457)
• Meets ISO 2470 and ISO 3688 standards
• Compact, lightweight and user-friendly
• Resolution: 0.1
• Repeat accuracy : ±0.1

PCE-ATP 1 is an ATP meter, tester, lumitester or luminometer used for surface testing. This luminometer allows for quick and easy first-generation adenosine triphosphate (ATP) testing and monitoring to ensure proper cleanliness, sterilization and sanitization. PCE-ATP 1 is an ATP tester that can be used for cleanliness control and documentation in many different applications.

• Measurement range: 0 … 999,999 relative light units (RLUs)
• Stores up to 10,000 date- and time-stamped data records to internal memory
• Enables rapid detection of bacterial or microbial residue

PCE-ATP 1 is a IoT sensor, ATP meter, lumitester or luminometer used for surface testing. This IoT sensor allows for quick and easy first-generation adenosine triphosphate (ATP) testing and monitoring to ensure proper cleanliness, sterilization and sanitization. PCE-ATP 1 is an IoT sensor that can be used for cleanliness control and documentation in many different applications.

• Measurement range: 0 … 999,999 relative light units (RLUs)
• Stores up to 10,000 date- and time-stamped data records to internal memory
• Enables rapid detection of bacterial or microbial residue

The class 1 sound level meter meets all requirements for noise measurement and frequency analysis. This integrating precision pulse sound level meter complies with all applicable standards and guidelines.

• Accuracy class 1
• A, B, C & Z frequency weighting
• Fast, Slow, Impulse and Peak time weighting
• Statistics function
• 1/1 octave band included
• 1/3 octave band optional

This Carbon Dioxide Meter Gas-Pro-1 can gauge with its sensors a maximum of four different gases. Because of this versatility, the Carbon Dioxide Meter Gas-Pro-1 is ideal for use in a variety of applications, such as: near canals, sewage treatment plants, drains, wastewater facilities, dumps/landfills, chemical/oil plants, shipping ports and more.

• Purpose: Personal protection
• Sensor type: CO / H2S / O2 / CH4
• Memory: Yes
• Interface: USB
• Includes suction pump
• Other gas sensors available upon request. (Please email jmu@pce-instruments.com (UK) or jwe@pce-instruments.com (US) for details!)

The 1-Phase-Power Meter PCE-GPA 62 (Graphic Power Quality Analyzer) with network analyzer / power and energy meter with data logger. The one-phase harmonic Analyzer (Graphic Power Quality Analyzer) is used for single-phase or three-phase measurements of active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics. This clamp meter is a perfect tool for all energetic measurements. It is delivered manufacturer calibrated and can be certified to ISO or standards.

• Real-time test, register and measurement of voltage and current (real and effective) 
• Measures power factor and phase angle, frequency, energy, active, reactive and apparent power   (single-phase or three-phase in symmetrical networks). 
• Max. conductor diameter: 55 mm / 2.2 in
• Records up to 50,000 records

This Air Quality Meter Gas-Pro-1 can gauge with its sensors a maximum of four different gases. Because of this versatility, the Air Quality Meter Gas-Pro-1 is ideal for use in a variety of applications, such as: near canals, sewage treatment plants, drains, wastewater facilities, dumps/landfills, chemical/oil plants, shipping ports and more.

• Purpose: Personal protection
• Sensor type: CO / H2S / O2 / CH4
• Memory: Yes
• Interface: USB
• Includes suction pump
• Other gas sensors available upon request. (Please email jmu@pce-instruments.com (UK) or jwe@pce-instruments.com (US) for details!)

The environmental meter kit is a useful tool to examine solar cells for their characteristic curves. This enables a statement to be made about the composition and design of a photovoltaic system.

Environmental meter PCE-PVA 100

• Measuring range: 0 … 12 A DC
• Three different test functions
• PC interface for data transferEnvironmental meter PCE-SPM 1
• Measuring range: 0 … 2000 W/m²
• Resolution: 1 W/m²
• Accuracy: ± 10 W/m² or ± 5%
• Data memory: 32,000 measured values
• Application, e.g .: photovoltaic systems

The class 1 data-logging noise meter / sound meter meets all requirements for noise measurement and frequency analysis. This integrating precision pulse noise meter / sound meter complies with all applicable standards and guidelines.

• Accuracy class 1
• A, B, C & Z frequency weighting
• Fast, Slow, Impulse and Peak time weighting
• Statistics function
• 1/1 octave band included
• 1/3 octave band optional