Call to Order
Monday - Friday
9:00 a.m. - 5:00 p.m. ET
(561) 320-9162
Monday - Friday
9:00 a.m. - 5:00 p.m. ET
(561) 320-9162
Air Air Meter / Wind Warning Device
Anemometer with pre-alarm and alarm / RS485 interface / display of wind speed / easy operation / display of the average speed of the last 2 and 5 minutes
The Air Quality Station can be used in different fields of application. In use, the Air Quality Station carries out measurements from the smallest wind movements. The Air Quality Station can be used on the one hand to monitor the current wind speed. On the other hand, it is also possible to use the Air Quality Station to measure the average value of the last two or five minutes. If the wind speed values are higher than the preset values, a pre-alarm is first activated before the alarm is output. Both alarms are given visually and acoustically on the Air Quality Station. If the pre-alarm takes effect, a yellow LED will flash on the front of the device and a beeper will emit a periodic warning tone. When the normal alarm needs to be activated, the red LED will flash and the beep will be played continuously by the device.
In general, the Air Quality Station is used wherever wind monitoring has to be carried out. This is often the case in factories, mines, wind turbines and similar. If necessary, a relay can also be connected to the Air Quality Station. In addition to the low wind speeds, the wind measuring device is characterized by its high reliability and high accuracy.
***Sensors sold separately***
| Power supply | 24 V DC | |
| Supply voltage for sensors (output) |
12V DC 24V DC |
|
| Measuring range | 0 ... 50 m/s | |
| Measuring accuracy | ± 3% of measuring range | |
| Signal input | 0 ... 10 V |
|
| Alarm relay |
|
|
| Interface | RS485 | |
| Operating temperature | -20 ... 60°C / -4 ... 140°F | |
| Protection class | IP66 | |
| Dimensions | 197.5 x 90 x 45 mm / 7.7 x 3.5 x 1.7 in |
1 x Air Quality Station PCE-WSAC 50-321
1 x User manual
1 x Sensor connector
1 x ISO Calibration certificate
Note: Wind sensor not included. This must be ordered separately.
ex. VAT, ex. delivery costs
ex. VAT, ex. delivery costs
The air flow meter is compatible with and can be mounted on to a wide variety of available measuring equipment. The sensor will detect even the minutest movements of air and the results are then output in analogue form.
- Output signal: 0 … 10V
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0.5 m/s … 50 m/s (1.1 ... 111.8 mph)
ex. VAT, ex. delivery costs
ex. VAT, ex. delivery costs
- up to 100 devices with 25 registers can be connected
- Configuration via webbrowser
- Interface: RS485, Ethernet
- Memory: 1 GB Flash
- additional inputs / outputs: digital input or relay output (selectable)
ex. VAT, ex. delivery costs
ex. VAT, ex. delivery costs
ex. VAT, ex. delivery costs
ex. VAT, ex. delivery costs
ex. VAT, ex. delivery costs
ex. VAT, ex. delivery costs
The air flow meter is compatible with and can be mounted on to a wide variety of available measuring equipment. The sensor will detect even the minutest movements of air and the results are then output in analogue form.
- Output signal: 4 … 20-mA
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0.5 m/s … 50 m/s (1.1 ... 111.8 mph)
[zoom]
[zoom]
[zoom]
[zoom]
[zoom]
[zoom]
[zoom]
[zoom]
[zoom]
[zoom]
