Leak Detector PCE-LDC 20
US$ 6,593.00
ex. VAT, ex. delivery costs
The leak detector for gas pressure systems is an effective solution for detecting and evaluating leaks in compressed air and other non-explosive gas pressure systems. The measured leaks can be recorded and analysed within the software, the escape of compressed air causes high electricity costs as compressors run more than they should.

Units: bar, psi, MPa, l/min, m³/h, cfm
Leak detection in compressed air, refrigerant
  and gas systems

- Leakage assessment
- Various attachments
- Wireless headphones
- Frequency: 38 . .. 42 kHz
- Measurement rate: 1 Hz
- Memory capacity: 1 GB
Gas Detector PCE-LDC 20
US$ 6,593.00
ex. VAT, ex. delivery costs
The gas detector for gas pressure systems is an effective solution for detecting and evaluating leaks in compressed air and other non-explosive gas pressure systems. The measured leaks can be recorded and analysed within the software, the escape of compressed air causes high electricity costs as compressors run more than they should.

Units: bar, psi, MPa, l/min, m³/h, cfm
Leak detection in compressed air, refrigerant
  and gas systems

- Leakage assessment
- Various attachments
- Wireless headphones
- Frequency: 38 . .. 42 kHz
- Measurement rate: 1 Hz
- Memory capacity: 1 GB
Flaw Detector PCE-FD 20
US$ 6,071.00
ex. VAT, ex. delivery costs

PCE-FD 20 is a portable ultrasonic flaw detector with a large LCD screen that displays A-scan maps of ultrasonic signals as well as B-scan cross sections. Ideal for use in mechanical engineering, aerospace and metallurgical applications, this high-frequency ultrasound-based flaw detector uses a contact transducer (two different probes included; 45° and 90°) to measure material thickness and identify flaws and defects such as discontinuity in welds.


- Operating frequency range: 1 ... 10 MHz
- Measured time interval range: 6 ... 1000 microseconds (µs)
- Sound velocity: 1000 ... 9999 m/s 

 

Gas Leak Detector PCE-LDC 20
US$ 6,593.00
ex. VAT, ex. delivery costs
The gas leak detector for gas pressure systems is an effective solution for detecting and evaluating leaks in compressed air and other non-explosive gas pressure systems. The measured leaks can be recorded and analysed within the software, the escape of compressed air causes high electricity costs as compressors run more than they should.

Units: bar, psi, MPa, l/min, m³/h, cfm
Leak detection in compressed air, refrigerant
  and gas systems

- Leakage assessment
- Various attachments
- Wireless headphones
- Frequency: 38 . .. 42 kHz
- Measurement rate: 1 Hz
- Memory capacity: 1 GB
Gas Leak Detector PCE-LDC 20
US$ 6,593.00
ex. VAT, ex. delivery costs
The gas leak detector for gas pressure systems is an effective solution for detecting and evaluating leaks in compressed air and other non-explosive gas pressure systems. The measured leaks can be recorded and analysed within the software, the escape of compressed air causes high electricity costs as compressors run more than they should.

Units: bar, psi, MPa, l/min, m³/h, cfm
Leak detection in compressed air, refrigerant
  and gas systems

- Leakage assessment
- Various attachments
- Wireless headphones
- Frequency: 38 . .. 42 kHz
- Measurement rate: 1 Hz
- Memory capacity: 1 GB
Ultrasonic Leak Detector PCE-LDC 20
US$ 6,593.00
ex. VAT, ex. delivery costs
The ultrasonic leak detector for gas pressure systems is an effective solution for detecting and evaluating leaks in compressed air and other non-explosive gas pressure systems. The measured leaks can be recorded and analysed within the software, the escape of compressed air causes high electricity costs as compressors run more than they should.

Units: bar, psi, MPa, l/min, m³/h, cfm
Leak detection in compressed air, refrigerant
  and gas systems

- Leakage assessment
- Various attachments
- Wireless headphones
- Frequency: 38 . .. 42 kHz
- Measurement rate: 1 Hz
- Memory capacity: 1 GB
Humidity Detector PCE-A-315
US$ 9,558.00
ex. VAT, ex. delivery costs

The humidity detector provides exceptionally accurate grain moisture measurement in real time. The humidity detector uses low-power microwaves to penetrate the surface every 0.2 second and obtain interior moisture readings without causing any damage. An integrated temperature probe ensures the readings are accurate from 5°C to 55°C / 41°F to 131°F. Suitable for the continuous monitoring of moisture in corn, soybeans, wheat, rice, sorghum, barley, oats, rye, hops, green coffee, cocoa beans, oil seeds, flax seeds, sunflower seeds, poppy seeds, pumpkin seeds, spelt seeds, buckwheat, sesame, peas, fava beans, scarlet runner beans, triticale, amaranth and jatropha.


- Boasts a measurement range of 5% to 40% for moisture content during
  continuous mass flow
with an error of just ±0.5% from 5% to 18% grain
  moisture
- Lowers energy costs by enabling shorter drying times and reduces labor costs
  by automating the moisture monitoring process
- Provides nearly maintenance-free operation, delivering consistently accurate
  moisture readings over time
- Analog output of 4 to 20 mA can be converted to digital for dryer control

 

Humidity Detector PCE-MWM 220
US$ 7,722.00
ex. VAT, ex. delivery costs

Humidity Detector for liquid materials are used in boiler installations, water-dosing and diesel oil emulsion dispersion systems. The scope of supply can include the control cabinet to operate the valves regulating water feed. The humidity detector for liquid materials has a processing unit with RS232/RS485 interfaces.


- Measurement range: 0 ... 100 %
- Temperature range: +5 ... +80 °C  (+41 ... +176 °F)

 

Cable Detector PCE-CL 20
US$ 389.00
ex. VAT, ex. delivery costs

The PCE-CL 20 is a cable detector or locator used to detect live and voltage-free electrical wires. This cable detector also can be used to locate metallic and non-metallic gas or water pipes, identify short circuits, and follow lines inside walls or under flooring.


- Output signal: 125 kHz
- Compatible with one- or two-pole circuits
- Automatic, manual and UAC measuring modes

 

Humidity Detector PCE-MWM 240-A
US$ 6,588.00
ex. VAT, ex. delivery costs

Designed specifically for use in humidity measurement of bulk materials, this humidity detector is installed in bins, silos, troughs, bunkers case, distributors, augers and conveyors. Material in bulk or flowing mass, such as fibrous materials, gravel, sawdust, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, seed, pastes, ... is continuously measurable.

- Stainless sensor rod (250 mm length)
- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C  (+41 ... +176 °F)
- Analog and digital signal output

Humidity Detector PCE-MWM 240-B
US$ 7,128.00
ex. VAT, ex. delivery costs

Suitable for determining the humidity of bulk substances, this absolute humidity detector can be fitted into containers and systems such as troughs, bunkers, distributors, augers, conveyors, bins and silos. This permits 24/7 moisture measurement of fibrous materials, sawdust, gravel, fly ash (mineral), wood chips (surface to 5 cm) feed grain, flour, pastes, seed, or similar bulk or flowing substances.

- PCE-MWM 240-B Rod sensor (custom length 500 ... 1500 mm)

- Lab analysis of your sample determines % error
- Measuring range: 0 ... 100%
- Material temperature range: -0 ... +80 °C  (+41 ... +176 °F)
- Analog and digital signal output

 

Humidity Detector PCE-MWM 300P
US$ 5,610.00
ex. VAT, ex. delivery costs

For industrial continuous production of wood pellets, chips, sawdust and similar materials when on-line moisture measurement for monitoring and controlling the drying and mixing process is important. Consistent quality of every batch, reduction of the consumption of materials, and shortest possible drying and mixing times are the criteria which are important in materials production. The humidity detector of PCE Instruments helps meet those criteria through highly accurate moisture measurement.


- Measuring range: 0 ... 100%
- The maximum permissible error (absolute): Lab analysis of your sample determines % error
- Temperature range: -40 ... +150 °C  (-40 ... +302 °F)
- Current consumption: 200 mA
- Power supply : 24 (18 ... 36) VDC
- Questionnaire starts evaluation process
- Application: pellets, wood chips

NDT Test Instruments PCE-COM 20
US$ 7,755.00
ex. VAT, ex. delivery costs

PCE-COM 20 is a portable handheld non-destructive conductivity tester for non-ferrous metals. This non-destructive testing (NDT) device uses eddy current to determine the electrical conductivity of non-ferrous metals such as aluminum and copper. Includes 3 standards for testing.

 

- Operating frequency: 60 kHz
- Sine wave probe: Ø 14 mm / ≈ 0.55 in
- Memory: Up to 500 groups of measurements
- Lift-off and temperature compensation
- Automatic calibration

Humidity Detector PCE-MWM 200
US$ 5,669.00
ex. VAT, ex. delivery costs

The humidity detector is a sensor for measuring moisture of sand consisting of a central probe surrounded by four other probes. The probes and sensor housing are made of stainless steel AISI 321. Our humidity detector is ideally suited for installation in tanks with liquid materials such as fuel oil, sludge from cement production, fuels (CWF).


- Readability mass fraction of water: 0 ... 100%
- Moisture measurement range: ± 0.1 ... 100% (water mass fraction))
- Maximum permissible absolute error moisture measurement: Varies by material, lab test required
- Temperature range: +5 ... +80 °C

Humidity Detector PCE-MWM 230
US$ 5,214.00
ex. VAT, ex. delivery costs

VHF-Band Moisture Meter Crushed Stone, Gravel, Ore (conveyor). The device is resistant to corrosion (stainless steel and dielectric materials) and can operate in the conditions deviating from the norm, for example, at temperatures of 145 °C. The humidity detector probe can be mounted on the walls in the hoppers, in pipelines or on trays in conveyors. Due to pluggable design this version of the humidity detector can also be used for soil moisture control.

- Measurement range: 0 ... 100 %
- Limits of error: <0.5% below 10% moisture
- Range of working temperatures:
  0 ... +90 °C (industrial version)
  0 ... +115 °C (extended temperature range) 
  0 ... +250 °C (drying kilns)

Humidity Detector PCE-DPM 10
US$ 5,120.00
ex. VAT, ex. delivery costs
The humidity detector from PCE Instruments enables precise determination of the dew point in pressurised systems. Thanks to its robust design, the device can be used for industrial applications up to 15 bar.

- Dew point measuring range from -100 ... +50 °C
- Pressure range up to 15 bar differential pressure
- Data logger for up to 100 million measured values
- Adjustable alarm limits
- Touch LC display
NDT Test Instrument PCE-VE 1500-22190
US$ 30,657.00
ex. VAT, ex. delivery costs
Wireless
With this NDT test instrument, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the NDT test instrument consists of braided tungsten.

- Diameter: Ø2.2mm / 0.08"
- Cable length: 1m / 3.2 ft
- Camera direction: 90°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission
NDT Test Instrument PCE-VE 1500-38209
US$ 30,657.00
ex. VAT, ex. delivery costs
Wireless
With this NDT test instrument, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the NDT test instrument consists of braided tungsten.

- Endoscope cable length: approx. 2 m / 6.5 ft
- Diameter: 3.8mm / 0.15"
- Camera resolution 160,000 pixels each
- Viewing angle front camera 120°, side camera 90°
- Focusing distance 5 … 50 mm / 0.19 ... 1.96" each
- Camera head length: 42 mm / 1.6"
- Bending radius at 90° 35 mm / 1.3"
- Live images from both cameras side by side
- 7" touch screen for easy operation
- Replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission