Anemometer PCE-WSAC 50W 24
US$ 1,571.00
ex. VAT, ex. delivery costs
The anemometer PCE-WSAC 50W is primarily used to measure and monitor the wind load on cranes or wind turbines. Furthermore, the wind situation can be measured and analyzed before commissioning a wind turbine. The high measuring range of up to 50 m/s of the anemometer means stormy gusts can also be monitored.

- Measuring range up to 180 km / h
- Input: pulse, analogue (4 ... 20-mA) or radio transmission
- 4 ... 20-mA analog output
- Supply voltage: 24V DC
- Ambient temperature -20 ... 70°C / -4 ... 158°F
- units adjustable: km / h, mph, m / s
Anemometer PCE-WSAC 50W 24-ICA Incl. ISO Calibration Certificate
US$ 1,742.00
ex. VAT, ex. delivery costs
ISO Calibration

The anemometer PCE-WSAC 50W 24-ICA is useful for measuring the wind speed to help determine the preferred site for a wind turbine installation. The device also monitors the wind load on existing wind farms, as well as on cranes for safey purposes. Due to the integrated 4 ... 20-mA analogue output of the anemometer, the measured data can also be transferred to other controllers for evaluation.


- Measuring range up to 180 km / h
- Input: pulse, analogue (4 ... 20-mA) or radio transmission
- 4 ... 20-mA analog output
- Supply voltage: 24V DC
- Ambient temperature -20 ... 70°C / -4 ... 158°F
- Units adjustable: km / h, mph, m / s 
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50W 230-ICA incl ISO calibration certificate
US$ 1,742.00
ex. VAT, ex. delivery costs
ISO Calibration

The anemometer PCE-WSAC 50W 230-ICA is useful for measuring the wind speed to help determine the preferred site for a wind turbine installation. The device also monitors the wind load on existing wind farms, as well as on cranes for safety purposes. Due to the integrated 4 ... 20-mA analogue output of the anemometer, the measured data can also be transferred to other controllers for evaluation.


- Measuring range up to 180 km / h
- Input: Pulse, analogue (4 ... 20-mA) or radio transmission
- 4 ... 20-mA analogue output
- Supply voltage: 110 ... 230V AC, 50/60 Hz
- Ambient temperature -20 .. . 70°C / -4 ... 158°F
- Units adjustable: km / h, mph, m / s
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-111
US$ 653.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-111 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 230 V AC
- Input signal: 4 ... 20 mA
- Communication: RS485
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-121
US$ 653.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-121 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 230 V AC
- Input signal: 0 ... 10 V
- Communication: RS485
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-211
US$ 653.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-211 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 115 V AC
- Input signal: 4 ... 20 mA
- Communication: RS485
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-221
US$ 653.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-221 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 115 V AC
- Input signal: 0 ... 10 V
- Communication: RS485
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-311
US$ 653.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-311 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 24 V DC
- Input signal: 4 ... 20 mA
- Communication: RS485
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-321
US$ 653.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-321 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 24 V DC
- Input signal: 0 ... 10 V
- Communication: RS485
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-910
US$ 561.00
ex. VAT, ex. delivery costs
ISO Calibration

A strong wind is not esssential to use the PCE-WSAC 50-910 anemometer, as it has a measuring range of 0 to 110 mph. In addition to the actual wind speed, this versatile anemometer can display the average wind speed over the last two minutes and five minutes. The anemometer is suitable for numerous wind detection applications in outdoor industries, e.g. on construction sites.


- Pre-alarm and full alarm with visual and audible warnings
- Measuring range: 0 ... 110 mph
- Power supply: 24 V DC
- Signal input: 4...20 mA
- incl. ISO calibration certificate

Anemometer PCE-WSAC 50-920
US$ 561.00
ex. VAT, ex. delivery costs
ISO Calibration

The PCE-WSAC 50-920 anemometer shows the speed of the wind and also the average figure over the prior two minutes and five minutes. The smallest wind motion is detected by this accurate anemometer. The timber industry, the mining industry, and the construction industry are some examples of applicable wind monitoring application areas for the anemometer.


- Pre-alarm and full alarm with visual and audible warnings
- Measuring range: 0 ... 110 mph
- Power supply: 24 V DC
- Signal input: 0...10 V
- incl. ISO calibration certificate

Anemometer PCE-WSAC 50-110
US$ 561.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-110 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Supply voltage: 230 V AC
- Input signal: 4 ... 20 mA
- 2 types of alarms
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-120
US$ 561.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-120 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 230 V AC
- Input signal: 0 ... 10 V
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-210
US$ 561.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-210 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 115 V AC
- Input signal: 4 ... 20 mA
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-220
US$ 561.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-220 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 115 V AC
- Input signal: 0 ... 10 V
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-320
US$ 561.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-320 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 24 V DC
- Input signal: 0 ... 10 V
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
Anemometer PCE-WSAC 50-310
US$ 561.00
ex. VAT, ex. delivery costs
ISO Calibration
The Anemometer PCE-WSAC 50-310 can be used in different fields of application. In use, the Anemometer carries out measurements from the smallest wind movements. The Anemometer  can be used to monitor and alert on the current wind speed.

- Wind measuring device with adjustable alarms
- 2 alarm types
- Supply voltage: 24 V DC
- Input signal: 4 ... 20 mA
- Sensor supply via evaluation device
- Degree of protection: IP66
- Incl. ISO calibration certificate
NDT Test Instrument PCE-VE 1500-22190
US$ 30,657.00
ex. VAT, ex. delivery costs
Wireless
With this NDT test instrument, weld seams, wear and tear and damage can be assessed quickly and easily in order to make quick diagnoses. The sheathing of the endoscope cable from the NDT test instrument consists of braided tungsten.

- Diameter: Ø2.2mm / 0.08"
- Cable length: 1m / 3.2 ft
- Camera direction: 90°
- Resolution: 160,000 pixels
- Focusing range: 5 ... 50 mm / 0.19 ... 1.96"
- 7" touch screen for easy operation
- replaceable battery with status display
- Storage of recording on SD card
- Motor with endoscope cable can be changed quickly
- HDMI connection for direct image transmission