Industrial Measurement Products and Solutions
Order no.: PCE-SC 09
The Class I Sound Level Meter Calibrator is a battery powered sound source. With the Class I sound calibrator, direct and fast calibrations of sound level meters and other systems for noise measurement can be carried out. 

- Sound pressure level: 94 dB, 114 dB
- Accuracy class: IEC 942, class 1
- Accuracy sound level: ± 0.3 dB (20°C / 68°C, 760 mm / 30 in Hg)
- Frequency: 1000 Hz for A, B, C and D frequency weighting
Manufacturer: PCE Instruments
US$ 718.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-SC 09
The Class I Decibel Meter Calibrator is a battery powered sound source. With the Class I sound calibrator, direct and fast calibrations of sound level meters and other systems for noise measurement can be carried out. 

- Sound pressure level: 94 dB, 114 dB
- Accuracy class: IEC 942, class 1
- Accuracy sound level: ± 0.3 dB (20°C / 68°C, 760 mm / 30 in Hg)
- Frequency: 1000 Hz for A, B, C and D frequency weighting
Manufacturer: PCE Instruments
US$ 718.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: ABBE-REF 1

ABBE-REF 1 is a high-precision Abbe refractometer for the accurate measurement of refractive indexes (nD), sucrose or sugar contents (% Brix) and mean dispersion values (nF-nC) of transparent and translucent liquids and substances. This bench-top Abbe refractometer can be used to determine refractive indexes in a temperature range from 0 ... +70 ºC (temperature control included).


Measurement ranges:
  1.300 ... 1.700 nD / 0.0 ... 95 % Brix
- Scale division: 0.0005 nD / 0.25 % Brix
- Resolution and accuracy: 0.0002 nD / 0.1 % Brix

Manufacturer: PCE Instruments
US$ 717.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-RGB2

PCE-RGB2 is a color meter for RGB (red, green, blue) or HSL (hue, saturation, luminance) color measurements. The colorimeter's 45 ° / 0 ° measurement geometry and 16 mm / ≈ 0.63" diameter aperture accommodate standardized color measurement methods on a variety of surfaces. The handheld color-measuring probe is connected to the colorimeter via a 1.5 m / 4.9' long cable, allowing a wide range of motion for the color measurement procedure.


- Measurement geometry: 45° / 0°
- Measurement range: RGB: 0 to 1023 / HSL: 0 to 1.00
- Resolution: 1 for RGB / 0.001 for HS
- Repeatability: < 3 RGB, for a minimum of 1 measurement
- Internal light source can be disabled to measure active light sources 

 

Manufacturer: PCE Instruments
US$ 717.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-RGB2

PCE-RGB2 is a colorimeter for RGB (red, green, blue) or HSL (hue, saturation, luminance) color measurements. The color meter's 45 ° / 0 ° measurement geometry and 16 mm / ≈ 0.63" diameter aperture accommodate standardized color measurement methods on a variety of surfaces. The handheld color-measuring probe is connected to the colorimeter via a 1.5 m / 4.9' long cable, allowing a wide range of motion for the color measurement procedure.


- Measurement geometry: 45° / 0°
- Measurement range: RGB: 0 to 1023 / HSL: 0 to 1.00
- Resolution: 1 for RGB / 0.001 for HS
- Repeatability: < 3 RGB, for a minimum of 1 measurement
- Internal light source can be disabled to measure active light sources 

 

Manufacturer: PCE Instruments
US$ 717.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-HT-75

The PCE-HT-75 Concrete Hardness Tester is easy to use and is fundamentally used in the construction industry as well as other industrial sectors (testing for Wickel hardness of rolls in commodities). This Hardness Tester in the form of a hammer device for testing concrete is based on the Swiss principle of measurement.


- Spring stretch: 75 ± 0.3 mm / 3 ± .01 in
- Measuring range: 10 ... 70 N/mm²
- Energy: 0.735 J / 0.54 ft-lbs 
- Low strength concrete testing or Type L
- Indication of measurement: 0 to 100 (without dimensions)
- Maximum thickness of concrete (of the material): 70 cm

Manufacturer: PCE Instruments
US$ 717.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-HT-75

The PCE-HT-75 durometer for concrete is easy to use and is fundamentally used in the construction industry as well as other industrial sectors (testing for Wickel hardness of rolls in commodities). This durometer in the form of a hammer device for testing concrete is based on the Swiss principle of measurement.


- Spring stretch: 75 ± 0.3 mm / 3 ± .01 in
- Measuring range: 10 ... 70 N/mm²
- Energy: 0.735 J / 0.54 ft-lbs
- Low strength concrete testing or Type L
- Indication of measurement: 0 to 100 (without dimensions)
- Maximum thickness of concrete (of the material): 70 cm

Manufacturer: PCE Instruments
US$ 717.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-MO 2002

Milliohm Meter with ruggedized and waterproof carrying case. Includes 4 test leads with clips.


- Measuring ranges / resolution: 5 ranges, 0 ... 200 mΩ / 0 ... 2000 Ω
- Accuracy: ± 0.5% of reading
- Max. Output voltage: (C1-C2) 20 V
- Power source 12V DC

 

Manufacturer: PCE Instruments
US$ 717.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-RGB2

PCE-RGB2 is a colorimeter for RGB (red, green, blue) or HSL (hue, saturation, luminance) color measurements. The color meter's 45 ° / 0 ° measurement geometry and 16 mm / ≈ 0.63" diameter aperture accommodate standardized color measurement methods on a variety of surfaces. The handheld color-measuring probe is connected to the colorimeter via a 1.5 m / 4.9' long cable, allowing a wide range of motion for the color measurement procedure.


- Measurement geometry: 45° / 0°
- Measurement range: RGB: 0 to 1023 / HSL: 0 to 1.00
- Resolution: 1 for RGB / 0.001 for HS
- Repeatability: < 3 RGB, for a minimum of 1 measurement
- Internal light source can be disabled to measure active light sources 

 

Manufacturer: PCE Instruments
US$ 717.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-HT-75

The PCE-HT-75 Surface Testing Hammer for concrete is easy to use and is fundamentally used in the construction industry as well as other industrial sectors (testing for Wickel hardness of rolls in commodities). This Surface Testing Hammer in the form of a hammer device for testing concrete is based on the Swiss principle of measurement.


- Spring stretch: 75 ± 0.3 mm / 3 ± .01 in
- Measuring range: 10 ... 70 N/mm²
- Energy: 0.735 J / 0.54 ft-lbs
- Low strength concrete testing or Type L
- Indication of measurement: 0 to 100 (without dimensions)
- Maximum thickness of concrete (of the material): 70 cm

Manufacturer: PCE Instruments
US$ 717.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: ABBE-REF 1

ABBE-REF 1 is a high-precision Abbe refractometer for the accurate measurement of refractive indexes (nD), sucrose or sugar contents (% Brix) and mean dispersion values (nF-nC) of transparent and translucent liquids and substances. This bench-top Abbe refractometer can be used to determine refractive indexes in a temperature range from 0 ... +70 ºC (temperature control included).


- Measurement ranges: 1.300 ... 1.700 nD / 0.0 ... 95 % Brix
- Scale division: 0.0005 nD / 0.25 % Brix
- Resolution and accuracy: 0.0002 nD / 0.1 % Brix

 

Manufacturer: PCE Instruments
US$ 717.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-NDL 10

The data logging condition monitoring device is used to determine volume. The PCE-NDL 10 data logging condition monitoring device is a handy measuring device that meets the highest requirements. In order to evaluate the measured data in the best possible way, it is possible to use the internal measurement data memory on the noise dosimeter. In addition, the data logging condition monitoring device has an SD card slot that enables the use of an SD card as an additional storage medium.


- Measuring range: SPL: Auto 30 ... 130 dB
- Resolution: 0.1 dB
- Low sampling rate
- Automatic or manual storage
- Selectable storage interval
- Backlit LC display
- Dose measurement or SPL measurement

Manufacturer: PCE Instruments
US$ 711.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-BTM 2000
The belt tension meter is an optical measuring instrument for determining the belt tension force. This force measuring device consists of a display unit and a sensor on a gooseneck cable. The force gauge measures the tension of the belt in a stationary state.

- Measures the oscillation frequency of the belt
- Measuring range: 10 ... 900 Hz
- Accuracy: ± (1% of rdg. + 4 digits)
- Resolution: <100 Hz: 0.1 Hz
                      >100 Hz: 1 Hz
- Memory for 750 measured values
- Sensor on gooseneck
Manufacturer: PCE Instruments
US$ 710.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-123-ICA

PCE-123 is a current calibrator used to test and calibrate a variety of measuring instruments. Offering a high level of accuracy for an affordable price, this easy-to-use current calibrator provides electrical (mA, mV, V and frequency in Hz) and temperature (in °C or °F) output signals, making the current calibrator useful in a wide range of applications.


- DC current: 4 - 20-mA (1 kΩ load, 24 V loop supply) with 1 μA resolution
- DC voltage: 0 - 100.00 mV, 0 - 1.000V, 0 - 12.000V
- K, J, E, T type thermocouples (°C or °F)
- Frequency: 1 - 62,500 Hz
- Incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
US$ 710.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-123-ICA

PCE-123 is a digital multimeter used to test and calibrate a variety of measuring instruments. Offering a high level of accuracy for an affordable price, this easy-to-use multimeter provides electrical (mA, mV, V and frequency in Hz) and temperature (in °C or °F) output signals, making the multimeter useful in a wide range of applications.


- DC current: 4 - 20-mA (1 kΩ load, 24 V loop supply) with 1 μA resolution
- DC voltage: 0 - 100.00 mV, 0 - 1.000V, 0 - 12.000V
- K, J, E, T type thermocouples (°C or °F)
- Frequency: 1 - 62,500 Hz
- Incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
US$ 710.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-123-ICA

PCE-123 is a electrical tester used to test and calibrate a variety of measuring instruments. Offering a high level of accuracy for an affordable price, this easy-to-use electrical tester provides electrical (mA, mV, V and frequency in Hz) and temperature (in °C or °F) output signals, making the electrical tester useful in a wide range of applications.


- DC current: 4 - 20-mA (1 kΩ load, 24 V loop supply) with 1 μA resolution
- DC voltage: 0 - 100.00 mV, 0 - 1.000V, 0 - 12.000V
- K, J, E, T type thermocouples (°C or °F)
- Frequency: 1 - 62,500 Hz
- Incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
US$ 710.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-BTM 2000
The belt tension meter is an optical measuring instrument for determining the belt tension force. This force measuring device consists of a display unit and a sensor on a gooseneck cable. The force gauge measures the tension of the belt in a stationary state.

- Measures the oscillation frequency of the belt
- Measuring range: 10 ... 900 Hz
- Accuracy: ± (1% of rdg. + 4 digits)
- Resolution: <100 Hz: 0.1 Hz
                      >100 Hz: 1 Hz
- Memory for 750 measured values
- Sensor on gooseneck
Manufacturer: PCE Instruments
US$ 710.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-123-ICA

PCE-123 is a multifunction calibrator used to test and calibrate a variety of measuring instruments. Offering a high level of accuracy for an affordable price, this easy-to-use multifunction calibrator provides electrical (mA, mV, V and frequency in Hz) and temperature (in °C or °F) output signals, making the multifunction calibrator useful in a wide range of applications.


- DC current: 4 - 20-mA (1 kΩ load, 24 V loop supply) with 1 μA resolution
- DC voltage: 0 - 100.00 mV, 0 - 1.000V, 0 - 12.000V
- K, J, E, T type thermocouples (°C or °F)
- Frequency: 1 - 62,500 Hz
- Incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
US$ 710.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-BTM 2000
The belt frequency meter is an optical measuring instrument for determining the belt tension force. This force measuring device consists of a display unit and a sensor on a gooseneck cable. The tension meter measures the tension of the belt in a stationary state.

- Measures the oscillation frequency of the belt
- Measuring range: 10 ... 900 Hz
- Accuracy: ± (1% of rdg. + 4 digits)
- Resolution: <100 Hz: 0.1 Hz
                      >100 Hz: 1 Hz
- Memory for 750 measured values
- Sensor on gooseneck
Manufacturer: PCE Instruments
US$ 710.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer
Order no.: PCE-123-ICA

PCE-123 is a process calibrator used to test and calibrate a variety of measuring instruments. Offering a high level of accuracy for an affordable price, this easy-to-use process calibrator provides electrical (mA, mV, V and frequency in Hz) and temperature (in °C or °F) output signals, making the process calibrator useful in a wide range of applications.


- DC current: 4 - 20-mA (1 kΩ load, 24 V loop supply) with 1 μA resolution
- DC voltage: 0 - 100.00 mV, 0 - 1.000V, 0 - 12.000V
- K, J, E, T type thermocouples (°C or °F)
- Frequency: 1 - 62,500 Hz
- Incl. ISO Calibration Certificate

Manufacturer: PCE Instruments
US$ 710.00

ex. VAT, ex. delivery costs

Test Instruments manufacturer