The Wind Speed Meter is compatible with and can be mounted on to a wide variety of available measuring equipment. The sensor will detect even the minutest movements of air and the results are then output in analogue form.

- Output signal: 0 … 10V
- Operating voltage: 12 … 36V DC
- Measurement reading range: 0.5 m/s … 50 m/s (1.1 ... 111.8 mph)

- Measuring range redox potential: 1100 ... +1100 mV
- Resolution redox potential: 1 mV
- Measuring accuracy redox potential: ± 1 mV ± 1 digit
- Robust housing (IP67)
- Measurement data memory for 50 data sets

Thanks to its small dimensions, the miniature force sensor is easy to use on hard-to-reach measuring points. The height in particular is something special with this force sensor. With a diameter of only 10 mm, this force sensor is smaller in diameter than a 1 cent coin.

 

- Rated load / force F.S.: 5-100 kg / 50-1000 N
- Limit load / force: 120 %
- Breaking load / force: 150 %
- Rated output: 1.0 – 1.5 mV/V

- Force sensor nominal load selectable!

A force sensor made of stainless steel with a measurement uncertainty of only 0.5%. With the dimensions of Ø 13 mm and a height of 7 mm, the force sensor is very versatile. 

 

- Rated load / force F.S.: 5-100 kg / 50-1000 N
- Limit load / force: 120 %
- Breaking load / force: 150 %
- Rated output: 1.0 – 1.5 mV/V

- Force sensor nominal load selectable!

This is a pressure cell as a force sensor with a high measuring range with small dimensions. The dimensions of the force sensor are only 9 mm in height and 19 mm in diameter. 

 

- Rated load / force F.S.: 5-500 kg / 50-5000N
- Limit load / force: 120 %
- Breaking load / force: 150 %
- Rated output: 1.0 – 1.5 mV/V

- Force sensor nominal load selectable!

The miniature force sensor can be used in many applications due to its compact dimensions. With a small force application surface, the miniature force transducer enables force measurement at small contact surfaces.

 

- Rated load / force F.S.: 10-50 kg / 100-500 N
- Limit load / force: 150 %
- Breaking load / force: 200 %
- Rated output: 1.0 – 1.5 mV/V

- Force sensor nominal load selectable!

The DIN-Rail Measuring Instrument PCE-SM1 is suitable for making analog signals bus-capable. Various analog signals such as 0 ... 20 mA, 0 ... 10 V, PT100 etc. are converted from the analog input module to RS485 Modbus.

 

- Input channels: 2
- Inputs: PT100, 0/4 ... 20 mA, 0 ... 10 V, 0 ... 40 Ω
- Interface: RS485 Modbus (ASCII RTU)
- Power supply: 85 ... 253 V / 20 ... 50 V AC / DC (selectable)

The RS232 TTL interface converter is a device-independent solution for converting an RS232 signal into a TTL signal. The RS232 TTL interface converter can also be used to convert a TTL signal into an RS 232 signal.

- For parallel and crossed connections
- Transmission speed up to 115,200 baud
- 3.5 mm jack and SUB D 9 interface

- Large CO2 measuring range up to 5000 ppm
- Traffic light function for carbon dioxide
- Measures temperature and humidity
- 5 h graph for long-term monitoring
- Battery and power adapter operation
- Suitable for classrooms, nurseries/kindergartens, lecture halls

The benchtop scale is a very precise measuring device for determining weights because of its resolution of 1 g and an accuracy of ± 0.1% of measuring range. The display units available on the benchtop scale are lb / oz, kg / g, kg, g, lb, oz.

- Measuring range: 0 ... 20 kg / 0 ... 44 lb
- Resolution: 1 g / 0.03 oz
- Accuracy: ± 0.1% of full scale
- Removable display
- Fold-out weighing platform
- Piece counting function
- incl. ISO Calibration Certificate

- Large CO2 measuring range up to 5000 ppm
- Traffic light function for carbon dioxide
- Measures temperature and humidity
- 5 h graph for long-term monitoring
- Battery and power adapter operation
- Suitable for classrooms, nurseries/kindergartens, lecture halls

Clamp Meter to test leakage / RMS measurement / continuity and resistance test. With the leakage Clamp Meter it is possible to measure leakage current with a range up to 100 A. The Clamp Meter can measure leakage current while current flows through electrical conductors that are not designed for conduction current. The leakage Clamp Meter is delivered manufacturer calibrated and can additionally be certified to ISO.

- Measures current up to 100 A
- Measures voltage up to 600 V
- Measures resistance up to 400 Ohms
- Test cables are included

 

Clamp on Tester to test leakage / RMS measurement / continuity and resistance test. The Clamp on Tester can measure leakage currents which appear when current flows through electrical conductors which are not designed for conduction current. The Clamp on Tester, as all test instruments, is delivered manufacturer calibrated, but can additionally be certified to ISO.

- Measures current up to 100 A
- Measures voltage up to 600 V
- Measures resistance up to 400 O
- Test cables are included

 

- Large CO2 measuring range up to 5000 ppm
- Traffic light function for carbon dioxide
- Measures temperature and humidity
- 5 h graph for long-term monitoring
- Battery and power adapter operation
- Suitable for classrooms, nurseries/kindergartens, lecture halls

The compact balance is a very precise measuring device for determining weights because of its resolution of 1 g and an accuracy of ± 0.1% of measuring range. The display units available on the compact balance are lb / oz, kg / g, kg, g, lb, oz.

- Measuring range: 0 ... 20 kg / 0 ... 44 lb
- Resolution: 1 g / 0.03 oz
- Accuracy: ± 0.1% of full scale
- Removable display
- Fold-out weighing platform
- Piece counting function
- incl. ISO Calibration Certificate

The counting scale is a very precise measuring device for determining weights because of its resolution of 1 g and an accuracy of ± 0.1% of measuring range. The display units available on the counting scale are lb / oz, kg / g, kg, g, lb, oz.

- Measuring range: 0 ... 20 kg / 0 ... 44 lb
- Resolution: 1 g / 0.03 oz
- Accuracy: ± 0.1% of full scale
- Removable display
- Fold-out weighing platform
- Piece counting function
- incl. ISO Calibration Certificate