This Gas Leak Detector is designed to detect formaldehyde in air. The Gas Leak Detector shows the formaldehyde-concentration on site and thereby avoids time-consuming and expensive analysis in laboratories. The formaldehyde Gas Leak Detector runs with the help of an electromechanical sensor and is designed to determine the current permitted limit. A measurement can be accomplished in less than 30 seconds.

- Measuring range: 0…10 ppm
- Short reaction time
- Real-time display
- Manual and auto data storage
- High-speed USB
- Software for Online Data transfer

The PCE-ITE 50 is a robust insulation tester with a large 3.5" TFT color LCD display. The insulation tester PCE-ITE 50 also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements.

- 3.5" color TFT LCD display
- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- SD card and Bluetooth
- Dual display
- Good / bad FI test
- Low Ohm measurement
- Up to 1000V terminal voltage

 

The PCE-TG 300-NO7 is an IoT meter for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the IoT meter. Wall thicknesses under a coating can also be measured with the IoT meter.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-ITE 50 is a robust IoT sensor with a large 3.5" TFT color LCD display. The IoT sensor also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements.

- 3.5" color TFT LCD display
- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- SD card and Bluetooth
- Dual display
- Good / bad FI test
- Low Ohm measurement
- Up to 1000V terminal voltage

The PCE-TG 300-NO7 is a material tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the material tester. Wall thicknesses under a coating can also be measured with the material tester.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is a material thickness meter for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the material thickness meter. Wall thicknesses under a coating can also be measured with the material thickness meter.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is a paint thickness tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the paint thickness tester. Wall thicknesses under a coating can also be measured with the paint thickness tester.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-ITE 50 is a robust PAT Tester with a large 3.5" TFT color LCD display. The PAT Tester also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements.

- 3.5" color TFT LCD display
- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- SD card and Bluetooth
- Dual display
- Good / bad FI test
- Low Ohm measurement
- Up to 1000V terminal voltage

The PCE-TG 300-NO7 is a thickness gauge for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the thickness gauge. Wall thicknesses under a coating can also be measured with the thickness gauge.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is a thickness meter for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the thickness meter. Wall thicknesses under a coating can also be measured with the thickness meter.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is an ultrasonic thickness gauge for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the ultrasonic thickness gauge. Wall thicknesses under a coating can also be measured with the ultrasonic thickness gauge.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is an ultrasonic thickness tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the ultrasonic thickness tester. Wall thicknesses under a coating can also be measured with the ultrasonic thickness tester.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is a wall thickness meter for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the wall thickness meter. Wall thicknesses under a coating can also be measured with the wall thickness meter.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

- Weighing range [Max]: 4200 g / 148 oz
- Readability: 0.01 g
- Calibration value: 0.1 g
- Weighing plate: 165 x 165 mm / 6.5 x 6.5"
- USB interface
- Graphic display
- Internal automatic adjustment
- incl. verification M II

The air quality meter is used in offices, workshops or in laboratories to carry out indicative measurements of the environmental conditions. In addition to the number of particles, the air quality meter determines the mass concentration of PM2.5 and PM10 in the measuring range 0 … 1000 µg/m³.

- Measurable particle sizes: PM2.5 / PM10
- Particle sizes: 0.3 / 0.5 / 1.0 / 2.5 / 5.0 and 10 µm
- Mass concentration
- Particle counter
- Temperature
- Humidity (RH)
- Flash memory for approx. 12 measurement runs

The air sampler is used in offices, workshops or in laboratories to carry out indicative measurements of the environmental conditions. In addition to the number of particles, the air sampler determines the mass concentration of PM2.5 and PM10 in the measuring range 0 … 1000 µg/m³.

- Measurable particle sizes: PM2.5 / PM10
- Particle sizes: 0.3 / 0.5 / 1.0 / 2.5 / 5.0 and 10 µm
- Mass concentration
- Particle counter
- Temperature
- Humidity (RH)
- Flash memory for approx. 12 measurement runs

The data logger for temperature and humidity is used in offices, workshops or in laboratories to carry out indicative measurements of the environmental conditions. In addition to the number of particles, the data logger for temperature and humidity determines the mass concentration of PM2.5 and PM10 in the measuring range 0 … 1000 µg/m³.

- Measurable particle sizes: PM2.5 / PM10
- Particle sizes: 0.3 / 0.5 / 1.0 / 2.5 / 5.0 and 10 µm
- Mass concentration
- Particle counter
- Temperature
- Humidity (RH)
- Flash memory for approx. 12 measurement runs