The PCE-TG 300-NO7 is a condition monitoring device for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the condition monitoring device. Wall thicknesses under a coating can also be measured with the condition monitoring device.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-ITE 50 is a robust earth tester with a large 3.5" TFT color LCD display. The earth tester also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements.

- 3.5" color TFT LCD display
- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- SD card and Bluetooth
- Dual display
- Good / bad FI test
- Low Ohm measurement
- Up to 1000V terminal voltage

The PCE-ITE 50 is a robust Electrical Tester with a large 3.5" TFT color LCD display. The Electrical Tester also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements.

- 3.5" color TFT LCD display
- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- SD card and Bluetooth
- Dual display
- Good / bad FI test
- Low Ohm measurement
- Up to 1000V terminal voltage

This Formaldehyde Meter HFX205 is designed to detect formaldehyde in air. The Formaldehyde Meter HFX205 shows the formaldehyde-concentration on site and thereby avoids time-consuming and expensive analysis in laboratories. The Formaldehyde Meter HFX205 runs with the help of an electromechanical sensor and is designed to determine the current permitted limit. A measurement can be accomplished in less than 30 seconds.

- Range Formaldehyde: 0…10 ppm
- Short reaction time
- Real-time display
- Manual and auto data storage
- High-speed USB
- Software for Online Data transfer

This Gas Detector is designed to detect formaldehyde in air. The Gas Detector shows the formaldehyde-concentration on site and thereby avoids time-consuming and expensive analysis in laboratories. The Gas Detector runs with the help of an electromechanical sensor and is designed to determine the current permitted limit. A measurement can be accomplished in less than 30 seconds.

- Range Formaldehyde: 0…10 ppm
- Short reaction time
- Real-time display
- Manual and auto data storage
- High-speed USB
- Software for Online Data transfer

This Gas Leak Detector is designed to detect formaldehyde in air. The Gas Leak Detector shows the formaldehyde-concentration on site and thereby avoids time-consuming and expensive analysis in laboratories. The formaldehyde Gas Leak Detector runs with the help of an electromechanical sensor and is designed to determine the current permitted limit. A measurement can be accomplished in less than 30 seconds.

- Measuring range: 0…10 ppm
- Short reaction time
- Real-time display
- Manual and auto data storage
- High-speed USB
- Software for Online Data transfer

The PCE-ITE 50 is a robust insulation tester with a large 3.5" TFT color LCD display. The insulation tester PCE-ITE 50 also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements.

- 3.5" color TFT LCD display
- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- SD card and Bluetooth
- Dual display
- Good / bad FI test
- Low Ohm measurement
- Up to 1000V terminal voltage

 

The PCE-TG 300-NO7 is an IoT meter for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the IoT meter. Wall thicknesses under a coating can also be measured with the IoT meter.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-ITE 50 is a robust IoT sensor with a large 3.5" TFT color LCD display. The IoT sensor also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements.

- 3.5" color TFT LCD display
- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- SD card and Bluetooth
- Dual display
- Good / bad FI test
- Low Ohm measurement
- Up to 1000V terminal voltage

The PCE-TG 300-NO7 is a material tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the material tester. Wall thicknesses under a coating can also be measured with the material tester.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is a material thickness meter for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the material thickness meter. Wall thicknesses under a coating can also be measured with the material thickness meter.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is an NDT test instrument for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the NDT test instrument. Wall thicknesses under a coating can also be measured with the NDT test instrument.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is a paint thickness tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the paint thickness tester. Wall thicknesses under a coating can also be measured with the paint thickness tester.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-ITE 50 is a robust PAT Tester with a large 3.5" TFT color LCD display. The PAT Tester also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements.

- 3.5" color TFT LCD display
- Loop resistance L-N, L-PE and N-PE
- Adjustable FI test current
- SD card and Bluetooth
- Dual display
- Good / bad FI test
- Low Ohm measurement
- Up to 1000V terminal voltage

The PCE-TG 300-NO7 is a thickness gauge for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the thickness gauge. Wall thicknesses under a coating can also be measured with the thickness gauge.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is a thickness meter for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the thickness meter. Wall thicknesses under a coating can also be measured with the thickness meter.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is an ultrasonic thickness gauge for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the ultrasonic thickness gauge. Wall thicknesses under a coating can also be measured with the ultrasonic thickness gauge.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth

The PCE-TG 300-NO7 is an ultrasonic thickness tester for measuring wall thickness. In general, the wall thicknesses of all homogeneous materials can be measured with the ultrasonic thickness tester. Wall thicknesses under a coating can also be measured with the ultrasonic thickness tester.

- Measuring range: 0.65 ... 200 mm / 0.025 ...  7.87" (steel)
- Diameter: 6 mm / 0.23"
- Minimum diameter of pipes: 15 x 2 mm / 0.59 x 0.07"
- Frequency: 7 MHz
- Bluetooth