Clamp on Tester

The PCE-830 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Clamp on Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 x 62 x 36 mm
• Incl. ISO calibration certificate

The PCE-830 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-6802 amp clamp (1000 A)
• Electrical conductor pick-up: 55 mm / 2.2 in diameter
• Range selection: manual (10 A, 100 A, 1000 A)
• Clamp dimensions: 244 x 97 x 46 mm / 9.6 x 3.8 x 1.8 in
• Incl. ISO calibration certificate

Clamp on Tester with network Analyzer / Clamp on Tester with data logger. The Clamp on Tester (Graphic Power Quality Analyzer) PCE-GPA 62 is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50? of the harmonic waveform. As all test instruments, the Clamp on Tester is delivered manufacturer calibrated (ISO certification is available optional).

• Real-time test, register and measurement of voltage and current (real and effective) 
• Measures power factor and phase angle, frequency, energy, active, reactive and apparent power   (single-phase or three-phase in symmetrical networks). 
• Max. conductor diameter: 55 mm / 2.2 in
• Records up to 50,000 records

This clamp on tester is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The clamp on tester is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

• Real-time test, register and measurement of voltage and current (real and effective) 
• Measures power factor and phase angle, frequency, energy, active, reactive and apparent power   (single-phase or three-phase in symmetrical networks). 
• Max. conductor diameter: 55 mm / 2.2 in
• Datalogger for 50,000 readings / software/ USB interface 
• incl. ISO Calibration Certificate

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

• Measuring range: 10 … 999.9 V
• AC voltage AC
• Alternating current AC
• Active power
• Power factor
• Phase angle
• Frequency
• Harmonic measurement
• Data memory: 512 kB   (non-volatile memory)
• incl. 4 current clamps / tapping terminals
• Standards: IP 30 / IEC 61 010, 600 V / CAT III
• incl. ISO Calibration Certificate
• incl. ISO Calibration Certificate

• direct voltage: 0.1 mV ... 1000 V
• alternating voltage: 0.1 mV ... 750 V
• alternating current: 0.1 ... 1000 A
• resistance: 0.1 Ω ... 60 MΩ
• capacitance: 1 nF ... 100 mF
• frequency: 0 Hz ... 10 MHz
• temperature sensor: -20 ... +1000 °C
• non-contact voltage detection (NCV)
• automatic and manual measurement range selection

Clamp on Tester for measuring AC current, AC voltage, DC current and frequency. The reduced dimensions of this device allow for measurements to be taken in places with limited access. The backlight display ensures that it is easy to read, even in places with limited light available, such as electrical cabinets or in cabling ducts. The Clamp on Tester (as all the test instruments) comes manufacturer calibrated - ISO certification is available as an option.

• AC current (50/60 Hz): 200 A / 0.1 A or 100-mA / ±3.0% + 8 digits
• DC current: 200 A / 100-mA / ±2.8% + 8 digits
• AC test voltage (without contact):100 VAC to 600 VAC at 50 /  60 Hz
• Frequency (3 ranges): 40 to 50 Hz / 51 to 510 Hz / 0.51 to 1 kHz

• DC voltage: 0 ... 100 V
• resolution: 0.0001 V
• accuracy: ±0.5 %
• resistance: 0 mΩ ... 200 Ω
• resolution: 0.01 mΩ
• accuracy: ±0.5 %
• connections: Kelvin clamps
• adjustable limit values
• internal memory

• direct voltage: 0.1 mV ... 1000 V
• alternating voltage: 0.1 mV ... 750 V
• direct current: 0.1 A ... 1000 A
• alternating current: 0.1 ... 1000 A
• resistance: 0.1 Ω ... 60 MΩ
• capacitance: 1 nF ... 100 mF
• frequency: 0 Hz ... 10 MHz
• temperature sensor: -20 ... +1000 °C
• non-contact voltage detection (NCV)
• automatic and manual measurement range selection