• temperature range: 100 ... 450 °C
• heat-up time in just a few seconds
• colour HD display
• incl. 3 interchangeable fine soldering tips
• 2 flexible arms "helping hands"
• sleep and standby mode
• adjustable alarm sound
• soldering tips can be changed quickly
• memory for 3 temperatures

• insulation resistance: 1 MΩ ... 200 GΩ
• resolution: 0.01 MΩ
• accuracy: ±(5 % of Rd. +10 digits)
• test voltages: 250 ... 2500 V
• voltage measurement: 10 ... 600 V
• resolution: 1 V
• accuracy: +(0.8 % of Rd. +5 digits)

• insulation resistance: 1 MΩ ... 200 GΩ
• resolution: 0.01 MΩ
• accuracy: ±(5 % of Rd. +10 digits)
• test voltages: 250 ... 2500 V
• voltage measurement: 10 ... 600 V
• resolution: 1 V
• accuracy: +(0.8 % of Rd. +5 digits)

• insulation resistance: 1 MΩ ... 200 GΩ
• resolution: 0.01 MΩ
• accuracy: ±(5 % of Rd. +10 digits)
• test voltages: 250 ... 2500 V
• voltage measurement: 10 ... 600 V
• resolution: 1 V
• accuracy: +(0.8 % of Rd. +5 digits)

The heating mantle PCE-HM 500 is an auxiliary device, which is used in laboratories. The heating mantle helps to heat or control the temperature of different samples or chemicals in the laboratory. The device has a crocheted net inside, in which you can hang the round bottom flask to heat it.

• Power 250 W
• Operating temperature 0 … +450 °C
• Fast heat-up time
• For round flasks up to 500 ml

The panel meter can process several different input signals, such as 0…410/4010 Ohm, -10…+63 mV DC, -13…+13 V DC, -24…+24 mA DC or signals from thermocouples and resistance thermometers. This makes the panel meter applicable in a wide range of applications. The measured values are shown on the large LED display of the panel meter.

• 21-point scaling
• IP 65 protection on the front
• Three-colored display
• Two alarm outputs

• insulation resistance: 1 MΩ ... 200 GΩ
• resolution: 0.01 MΩ
• accuracy: ±(5 % of Rd. +10 digits)
• test voltages: 250 ... 2500 V
• voltage measurement: 10 ... 600 V
• resolution: 1 V
• accuracy: +(0.8 % of Rd. +5 digits)

The DIN-Rail Measuring Instrument PCE-SM1 is suitable for making analog signals bus-capable. Various analog signals such as 0 … 20 mA, 0 … 10 V, PT100 etc. are converted from the analog input module to RS485 Modbus.

• Input channels: 2
• Inputs: PT100, 0/4 … 20 mA, 0 … 10 V, 0 … 40 Ω
• Interface: RS485 Modbus (ASCII RTU)
• Power supply: 85 … 253 V / 20 … 50 V AC / DC (selectable)

Voltmeter to test leakage / RMS measurement / continuity and resistance test.

• Measures current up to 100 A
• Measures voltage up to 600 V
• Measures resistance up to 400 O
• Test cables are included

The process controller / temperature controller is a simple temperature controller for control tasks. The input signal of the thermostat is processed by the Pt100 sensor in different temperature ranges. Optionally the simple temperature controller can also be equipped with a PID switch.

• Power supply: 85 … 253 V AC / DC
• Sensor Input: for Pt100 sensor
• Measuring ranges: up to max. 600 °C (selectable)
• Output: Relay or SSR output (selectable) 

The conductivity meter is a good solution for anyone who wants to check the conductivity of ultrapure water and to accurately determine the salinity of liquids. 

• conductivity: 0 … 20 µS/cm …
• salinity: 0,00 … 10.00 ppt
• temperature: 0 … 60 °C / 32 … 140 °F
• automatic temperature compensation
• internal 3-point calibration

Clamp Meter to test leakage / RMS measurement / continuity and resistance test. With the leakage Clamp Meter it is possible to measure leakage current with a range up to 100 A. The Clamp Meter can measure leakage current while current flows through electrical conductors that are not designed for conduction current. The leakage Clamp Meter is delivered manufacturer calibrated and can additionally be certified to ISO.

• Measures current up to 100 A
• Measures voltage up to 600 V
• Measures resistance up to 400 Ohms
• Test cables are included

Clamp on Tester to test leakage / RMS measurement / continuity and resistance test. The Clamp on Tester can measure leakage currents which appear when current flows through electrical conductors which are not designed for conduction current. The Clamp on Tester, as all test instruments, is delivered manufacturer calibrated, but can additionally be certified to ISO.

• Measures current up to 100 A
• Measures voltage up to 600 V
• Measures resistance up to 400 O
• Test cables are included

Digital Multimeter to test leakage / RMS measurement / continuity and resistance test.

• Measures current up to 100 A
• Measures voltage up to 600 V
• Measures resistance up to 400 O
• Test cables are included

Electrical Tester to test leakage / RMS measurement / continuity and resistance test.

• Measures current up to 100 A
• Measures voltage up to 600 V
• Measures resistance up to 400 O
• Test cables are included

With the Current Clamp it is possible to measure leakage currents up to a range of 100 A. The Current Clamp can measure leakage currents which appear when current flows through electrical conductors which are not designed for conduction current.

• Measures current up to 100 A
• Measures voltage up to 600 V
• Measures resistance up to 400 O
• Test cables are included

• Two-stage temperature: 400 / 850°C (752 / 1562°F)
• Sterilisation in 5 ... 7 seconds
• Power supply: 220 ... 240V AC | 50 / 60 Hz
• Inner diameter: 35 mm / 1.4 in
• Internal length: 100 mm / 4 in