• Torque: 0 ... 50 Nm 0 ... 37 ft-lb
• Resolution: 0.001 Nm / 0.0007 ft-lb
• Accuracy: ±1 % v.Mw.
• Continuous measurement or peak value
• Units: Nm, kgf cm and lbf in
• RS232 interface
• 99 memory locations
• Software

PCE-CPT 20 is a Material Tester, or surface coating flexibility testing device, used for testing the formability, ductility, adhesion and elongation of paints, lacquers, varnishes, powder and protective coatings on sheet metal. Used in manufacturing production, paint shop and quality control applications, the Material Tester aids in determining coating strength, durability and elasticity.

• Tests surface coatings on metal sheets 0.3 to 1.25 mm thick
• Provides a maximum depression force of 2500 N
• Offers a display resolution of 0.01 mm

PCE-HT 225E is a material test hammer, also called a concrete rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

• Test range: 10 … 60 MPa or 100 … 600 kg/cm² / 1450.38 … 8702.26 psi
• Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
• Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
• Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
• Data processing software included

The portable and easy-to-use material tester with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The material tester uses a DSP chip for control and data processing at high speed and low energy consumption.

• 21 measurement parameters:   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
• Large graphic OLED display
• Memory: 20 measurement histories with all parameters
• USB interface
• Incl. ISO calibration certificate

PCE-CPT 20 is a Material Tester, or surface coating flexibility testing device, used for testing the formability, ductility, adhesion and elongation of paints, lacquers, varnishes, powder and protective coatings on sheet metal. Used in manufacturing production, paint shop and quality control applications, the Material Tester aids in determining coating strength, durability and elasticity.

• Tests surface coatings on metal sheets 0.3 to 1.25 mm thick
• Provides a maximum depression force of 2500 N
• Offers a display resolution of 0.01 mm

The material surface roughness tester PCE-RT 2000BT-ICA is used for accurate measurement of surface roughness. The material surface roughness tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

• Measuring ranges Ra, Rq, Rc: 0.005 µm … 16 µm / 0.197 µinch … 629.9 µinch
• Measurement accuracy: <± 10%
• Micro USB interface
• Bluetooth
• 3 different cut-off wavelengths
• Download free app from the Google Play Store
• incl. ISO Calibration Certificate

• Magnetic flux: 0 ... 250 mVs
• Resolution: 0.001 mVs - Accuracy: 2%
• Helmholtz torque coil HM-2
• Graphical integral of the impulse curve
• Real flux, magnetic moment, flux density
• Memory and interface
• No drift
• LCD touch panel
• Wireless interface

• Magnetic flux: 0 ... 250 mVs
• Resolution: 0.001 mVs - Accuracy: 2%
• Helmholtz moment coil HM-1
• Graphical integral of the impulse curve
• Real flux, magnetic moment, flux density
• Memory and interface
• No drift
• LCD touch panel
• Wireless interface

• Measuring range: 1 - 100 Fe%, 1 - 140 FN
• Measurement of the ferrite content in austenitic and duplex steels
• Single measurement or continuous measurement with averaging
• Smallest measuring surface: ø 2 mm
• Measured value memory: 4000 measured values can be flexibly divided up
• Statistics: number / maximum / minimum / mean value / standard deviation
• Wireless interface for communication with Android, iOS and Windows

PCE-HT 225E is a durometer, also called a concrete rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

• Test range: 10 … 60 MPa or 100 … 600 kg/cm² / 1450.38 … 8702.26 psi
• Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
• Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
• Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
• Data processing software included

PCE-HT 225E is a hardness test hammer, also called a concrete rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

• Test range: 10 … 60 MPa or 100 … 600 kg/cm² / 1450.38 … 8702.26 psi
• Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
• Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
• Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
• Data processing software included

PCE-HT 225E is a concrete test hammer, also called a concrete rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

• Test range: 10 … 60 MPa or 100 … 600 kg/cm² / 1450.38 … 8702.26 psi
• Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
• Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
• Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
• Data processing software included

PCE-HT 225E is a roll hardness test hammer, also called a rolled paper rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with rolled paper, concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

• Test range: 10 … 60 MPa or 100 … 600 kg/cm² / 1450.38 … 8702.26 psi
• Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
• Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
• Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
• Data processing software included

PCE-HT 225E is a surface testing concrete test hammer, also called a concrete rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

• Test range: 10 … 60 MPa or 100 … 600 kg/cm² / 1450.38 … 8702.26 psi
• Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
• Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
• Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
• Data processing software included

Our universal testing machine PCE-MTS500 can be coupled and operated in a wide variety of versions with our force gauges, the PCE series. The universal testing machine lets you carry out almost all of your compression and tensile force applications with repeatability. The use of the universal testing machine offers the operator the most precise equality of test bench and sample.

• Measuring range: max. 5000 N / 500 kg
• Feed speed: 30 mm/min … 230 mm/min
• All PCE devices adaptable
• Robust steel design
• ** N.B. The mounting plate ADP-UNI accessory must be ordered for internal load cell force gauges ***

The profilometer PCE-RT 2000BT-ICA is used for accurate measurement of surface roughness. The profilometer can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

• Measuring ranges Ra, Rq, Rc: 0.005 µm … 16 µm / 0.197 µinch … 629.9 µinch
• Measurement accuracy: <± 10%
• Micro USB interface
• Bluetooth
• 3 different cut-off wavelengths
• Download free app from the Google Play Store
• incl. ISO Calibration Certificate

The portable and easy-to-use profilometer with an OLED display is particularly suitable for quick and accurate measurements in the workshop or laboratory. The profilometer uses a DSP chip for control and data processing at high speed and low energy consumption.

• 21 measurement parameters:   Ra, Rq, Rsm, Rsk, Rz, Rt, Rp, Rv, Rc,   Rmax, Ry (JIS), Rz (JIS), RP (ASME), Rpm (ASME),   Rv (ASME), R3z, R3zmax, Rz1max, Rmr (c), Rdc, Rmr
• Large graphic OLED display
• Memory: 20 measurement histories with all parameters
• USB interface
• Incl. ISO calibration certificate

Concrete tester / concrete measuring device, also called a concrete rebound hammer or Swiss hammer, used for non-destructive measurements of surface hardness and compression strength. Suitable for use with concrete, rock and building materials, this rebound hammer features a direct digital display, voice functionality, USB port data interface and memory for storing up 200 measurement values.

• Test range: 10 … 60 MPa or 100 … 600 kg/cm² / 1450.38 … 8702.26 psi
• Impact energy: 2.207 J or N-m / 0.225 kgf.m / 1.6278 ft-lb or Type N
• Impact stroke: 75 ± 0.3 mm / 2.95 ± 0.012 in
• Radius of spherical tip: 25 ± 1 mm / 0.99 ± 0.04 in
• Data processing software included

Our test stand for force gauge PCE-MTS500 can be coupled and operated in a wide variety of versions with our force gauges, the PCE series. The test stand for force gauge lets you carry out almost all of your compression and tensile force applications with repeatability. The use of the test stand for force gauge offers the operator the most precise equality of test bench and sample.

• Measuring range: max. 5000 N / 500 kg
• Feed speed: 30 mm/min … 230 mm/min
• All PCE devices adaptable
• Robust steel design
• ** N.B. The mounting plate ADP-UNI accessory must be ordered for internal load cell force gauges ***

The force gauge is ideal for mobile tensile measurements, such as those carried out by surveyors. Quality materials are used in the manufacture of the force gauge. Despite the high measuring capacity, these materials enable a compact design with a low weight.

• Measurement range: 20,000 kg / 200 kN / 44,092 lb
• Resolution: 10 kg / 100 N / 22 lb
• Minimum load: 200 kg / 440 lb
• Supplied without remote control indicator
• incl. ISO Calibration Certificate