Products for 'FK t' | PCE Instruments

94,90 €

Price excl. VAT &. delivery

The digital panel meter is used for processing signals coming from temperature sensors. Depending on your specific needs, the panel meter can be ordered with different inputs for thermocouples (type J, K) or resistance thermometers (Pt100). The input signal of the panel meter is freely scalable, which increases its application possibilities.

IP65 protected front
For thermocouples and resistance thermometers
Configuration via software
5-digit LED display

Panel Meter PCE-N20T

124,90 €

Price excl. VAT &. delivery

The digital panel meter is used for processing signals from Pt100 temperature sensors or thermocouples (type J, K). The measurement results are shown on the large 5-digit LED-display of the panel meter. Depending on the actual values, the temperature can be shown in three different colors, which makes it easier to evaluate them.

Input: Pt100, thermocouple type J or type K
Accuracy: ± (0.2 % FS + 1 dgt.)
two open collector outputs
24 V power supply sytem for sensors and transducers
5-digit, three-coloured LED display

Panel Meter PCE-ULM 10

555,90 €

Price excl. VAT &. delivery

The panel meter is the ideal measuring device to determine the fill level of a silo. Thanks to the 4 … 20-mA output signal, the panel meter can also be connected to the operational process control.

Measuring range: 0 … 10 m / 0 … 32.8 ft
Accuracy: 0.5%
Resolution: 0.001 m
With display for setting and reading
Stable M60 connection thread

Panel Meter PCE-N50F

691,90 €

Price excl. VAT &. delivery

The panel meter is suitable for panel mounting. This panel meter can be used to indicate the weight, force or torque. The decisive factor here is the type of sensor that is connected to the panel meter.

Signal input range: 0 … 20 mV
Units: g, mN, mlb, Pa, kg, N, Ib, kPa, t, kN, klb, MPa
For load cells, force sensors, etc.
Up to 1600 Hz sampling rate
LCD display

Panel Meter PCE-N30P

203,90 €

Price excl. VAT &. delivery

The panel meter can determine the most important system parameters of a single-phase network. Based on the current and voltage, the panel meter calculates the apparent, active and reactive power, as well as the phase difference angle and the power factor. The panel meter can also determine the average power for a 15 minute period and the average voltage for a 10 minute period.

Input: 0.02…6 A / 0…480 V / 45.00…100.00 Hz
Accuracy: 0.2 %
IP65 protected front
two alarm outputs

Panel Meter PCE-N30U

188,90 €

Price excl. VAT &. delivery

The panel meter can process several different input signals, such as 0…410/4010 Ohm, -10…+63 mV DC, -13…+13 V DC, -24…+24 mA DC or signals from thermocouples and resistance thermometers. This makes the panel meter applicable in a wide range of applications. The measured values are shown on the large LED display of the panel meter.

21-point scaling
IP 65 protection on the front
Three-colored display
Two alarm outputs

Panel Meter PCE-DPD-F2

340,90 €

Price excl. VAT &. delivery

The built-in display is used to indicate the force and weight, which is determined by force sensors and load cells with strain gauges. The output signal of the measuring cell is irrelevant because the panel meter makes it possible to display the correct weight in mV / V based on the set sensitivity. The panel meter shows the measured values on a 6-digit LED display.

Power supply: 11 … 60V DC / 24/48V AC
Input signal: mV / V for force and weighing sensors
Display: 6 digits, red
Digit height : 14 mm

Panel Meter PCE-N25S

84,90 €

Price excl. VAT &. delivery

The panel meter is used for processing standardised signals. Depending on your specific needs, the panel meter can be ordered with different inputs, such as 0…20 mA, 4…20 mA, 0…60 mV, 0…10 V, ±60 mV or ±10 V. The input signal of the panel meter is freely scalable, which increases its application possibilities.

IP65 protected at the front
6 different standardised signal inputs available
configuration via software
5-digit LED display

Panel Meter PCE-DPD-F1

328,90 €

Price excl. VAT &. delivery

The built-in display is used to indicate the force and weight, which is detected by force sensors and load cells with strain gauges. The output signal of the measuring cell is irrelevant because the panel meter makes it possible to display the correct weight in mV / V based on the set sensitivity. The panel meter shows the measured values on a 6-digit LED display.

Power supply: 85 … 265V AC / DC
Input signal: mV / V for force and weighing sensors
Display: 6 digits, red
Digit height : 14 mm