PCE Instruments: Test Instruments

Order no.: F603

The Clamp on Tester of the F600 series measures the current up to 2000 A (3000 A peak). This current clamp determines the effective value.


- Measurement type: TRMS [AC] / DC
- AC A: 0.15 ... 2000 A (3000 A peak)
- DC A: 0.15 ... 3000A
- Accuracy: 1% v Mw. + 3 digits

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: F605

The current clamp of the F600 series measures the current up to 2000 A (3000 A peak). This current clamp determines the effective value.


- Measurement type: TRMS [AC, AC + DC] DC
- Power output: 1 W ... 2000 kW
- Reactive power: 1 var ... 2000 kvar
- Apparent power: 1 VA ... 2000 kVA

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: F607

The current clamp of the F600 series measures the current up to 2000 A (3000 A peak). This current clamp determines the effective value.


- Measurement type: TRMS [AC, AC + DC] DC
- frequency analysis: 25th order
- Switching threshold Continuity test: 40 Ω
- Interface: Bluetooth

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: F62

The leakage Clamp on Tester F62 detects current clamp isolation faults. Besides leakage current measurements this Clamp on Tester measures up to 100 A. In general all the test instruments are delivered to the custumer calibrated by the manufacturer - a certification according to ISO is available as an option.


- Measuring range: 0 ... 100 A, 0 ... 600 V, 0 ... 1000 Ω
- Resolution: 10 µA ... 100 mA, 0.1 V, 0.1 Ω
- Accuracy: ±1.5 %
- CAT III 600 V
- Multimeter function
- 4 different measuring ranges

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: F65

The leakage HVAC Meter F65 detects current clamp isolation faults. Besides leakage current measurements this HVAC Meter measures up to 100 A. In general all the test instruments are delivered to the custumer calibrated by the manufacturer - a certification according to ISO is available as an option.


- Measuring range: 0 ... 100 A, 0 ... 600 V, 0 ... 1000 Ω
- Resolution: 10 µA ... 100 mA, 0.1 V, 0.1 Ω
- Accuracy: ±1.5 %
- CAT III 600 V
- Multimeter function
- 5 different measuring ranges

 

Manufacturer: Chauvin Arnoux GmbH
Test Instruments manufacturer
Order no.: KYORITSU 6305 / 3000A

The Kyoritsu 6305 Clamp on Tester can measure up to 3000 A in different ranges. In addition to the current measurement, the Clamp on Tester also measures other parameters such as voltage, active power, apparent power, apparent energy, reactive power, power factor, and frequency. The Clamp on Tester is delivered manufacturer calibrated. ISO or UTIL certification is optionally available.
- Digital power measurement
- Up to 3000 A range transformers, flex converters
- Many measurement parameters
- Datalogger, Memory, Interface

Manufacturer: EVOMEX
Test Instruments manufacturer
Order no.: KYORITSU 6305 / 500A

The Kyoritsu 6305 / 500 A Clamp on Tester is a very easy to use energy logger. The clearly arranged control panel on the Clamp on Tester and the instructions on the screen allow the user to quickly record the selected measurement function.
- Digital power measurement
- Up to 500 A with converter pliers
- Many measurement parameters

Manufacturer: EVOMEX
Test Instruments manufacturer
Order no.: KYORITSU 6315 / 3000A

The Kyoritsu 6315 / 3000 A Clamp on Tester is used for the analysis of performance and harmonics. The Clamp on Tester can safely measure currents of up to 3000 A. The Clamp on Tester also measures the phase angle, harmonics, apparent power, active power, and work. All measurable variables are shown on the color display of the Clamp on Tester. The Clamp on Tester's built-in memory has a size of 3 MB, sufficient for a data record of about 2 days.
- Harmonic Analysis
- Measurement of voltage and current
- Up to 3000 A
- Long recording duration > 1 year
- Manufacturer calibrated (ISO optional)

Manufacturer: EVOMEX
Test Instruments manufacturer
Order no.: KYORITSU 6315 / 500A

The Kyoritsu 6315 / 500 A Clamp on Tester is used for the analysis of performance and harmonics. The Clamp on Tester can safely measure currents of up to 500 A. The Clamp on Tester also measures the phase angle, harmonics, apparent power, active power, and work. The Clamp on Tester's built-in memory has a size of 3 MB and is therefore sufficient for a data record of about 2 days.
- 3 GB internal memory, up to 2 GB external memory
- Measurement of voltage and current
- Harmonic Analysis
- Frequency measurement up to 40 Hz ... 70 Hz
- Up to 500 A

Manufacturer: EVOMEX
Test Instruments manufacturer
Order no.: PCE-830-1

The PCE-830 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

Manufacturer: PCE Instruments
Order no.: PCE-830-2

The PCE-830-2 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

Manufacturer: PCE Instruments
Order no.: PCE-830-3

The PCE-830-3 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-3007 flexible amp clamp (3000 A)
- Electrical conductor pick-up: 170 mm / 6.69 in diameter
- Length of electrical conductor: 610 mm / 24.0 in
- Dimensions: 257 mm x 155 mm x 57 mm / 10.1 in x 6.1 in x 2.2 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values - single phase)

Manufacturer: PCE Instruments
Order no.: PCE-CM 4

By using the clamp on tester PCE-CM 4, you are able to perform AC measurements on electrical conductors without having to disconnect them. Just put the flexible clamp of the clamp on tester around the conductor to be measured and start the measurement. The flexible design of the clamp allows measurements even on hard to reach conductors.


- Range: 4 A / 40 A / 400 A AC
- Resolution: 0.001 A / 0.01 A / 0.1 A AC
- Accuracy: ± 3 %
- Easy to use

 

Manufacturer: PCE Instruments
Order no.: PCE-DC 41

The clamp on tester PCE-DC 41 can measure voltages up to 600 V, currents up to 600 A and electrical resistance up to 1000 ?. To perform a measurement, you can either use the measuring leads, which are included in the package of the clamp on tester, or you can use the integrated clamp mechanism. By using the clamp of the clamp on tester, you are able to measure the electrical parameters of an electrical conductor contact-free and without disconnecting it.


- Voltage: 600 V AC/DC
- Current: 600 A AC/DC
- Electrical Resistance: 1000 Ω
- Clamp mechanism

 

Manufacturer: PCE Instruments
Order no.: PCE-DC1

Clamp on Tester for measuring AC current, AC voltage, DC current and frequency. The reduced dimensions of this device allow for measurements to be taken in places with limited access. The backlight display ensures that it is easy to read, even in places with limited light available, such as electrical cabinets or in cabling ducts. The Clamp on Tester (as all the test instruments) comes manufacturer calibrated - ISO certification is available as an option.


- AC current (50/60 Hz): 200 A / 0.1 A or 100 mA / ±3.0% + 8 digits
- DC current: 200 A / 100 mA / ±2.8% + 8 digits
- AC test voltage (without contact):100 VAC to 600 VAC at 50 /
  60 Hz
- Frequency (3 ranges): 40 to 50 Hz / 51 to 510 Hz / 0.51 to 1 kHz

 

Manufacturer: PCE Instruments
Order no.: PCE-DC2

Digital Clamp Meter for measuring AC/DC current, AC voltage and resistance. This clamp meter is designed to indirectly detect AC/DC current and ohms. The clamp has white LEDs which illuminate the point of measurement and test the voltage without contact. Small dimensions of this device allow to take measurements in places with limited access. The clamp meter comes manufacturer calibrated and can optionally be certified according to ISO or standards.


- AC / DC current, voltage and resistance measurement
- 3 2/3-digit LCD display
- Power supply: 2 x 1.5V AAA battery
- Dimensions: 164 x 65 x 32 mm / 6.4 x 2.5 x 1.2 in

 

Manufacturer: PCE Instruments
Order no.: PCE-DC3

Clamp on Tester to determine indirectly, the AC/DC currents with high accuracy.


- AC current (50 / 60 Hz): 2 A  / 1 mA / ± 2.8 % + 10 dgt
- DC current: 2 A / 1 mA / ± 3.0 % + 10 dgt
- AC overload protection: 100 VAC up to 600 VAC 50 / 60 Hz

 

Manufacturer: PCE Instruments
Order no.: PCE-GPA 62

Clamp on Tester with network Analyzer / Clamp on Tester with data logger. The Clamp on Tester (Graphic Power Quality Analyzer) PCE-GPA 62 is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50? of the harmonic waveform. As all test instruments, the Clamp on Tester is delivered manufacturer calibrated (ISO certification is available optional).


- Voltage measurement: 4.0 ... 600.0 V RMS value ± 0,5 %,
  ± 5 digits / 0,1 V
- Voltage peaks (> 10V): 50 Hz - 60 Hz / ± 5 % ± 50 digits
- Current measurements: 4.0 ... 1500.0 A real ± 1% V. ± 5 digits /
  0,01 A
- Current peaks (> 20A):  50 Hz - 60 Hz / ± 5 % ± 50 digits

 

Manufacturer: PCE Instruments
Order no.: PCE-LCT 1

Clamp on Tester PCE-LCT 1 to test leakage / RMS measurement / continuity and resistance test. The Clamp on Tester can measure leakage currents which appear when current flows through electrical conductors which are not designed for conduction current. The Clamp on Tester, as all test instruments, is delivered manufacturer calibrated, but can additionally be certified to ISO.


- Measures current up to 100 A
- Measures voltage up to 600 V
- Measures resistance up to 400 O
- Test cables are included

 

Manufacturer: PCE Instruments
Order no.: PCE-PA 8000

With the PCE-PA 8000 Clamp on Tester you will be able to perform prolonged measurements of electrical properties. The measurement data is saved in xls format on the included SD card to be easily transferred to a computer or laptop for review. The Clamp on Tester comes manufacturer calibrated and can be certified to ISO or UTIL standards as an option.
- Display: 3.7 in / 94 mm LCD (320 x 240 pixels) with LED backlight
- Electrical properties: AC V, AC A, active power, apparent power, power factor, phase angle, power frequency
- Voltage ranges: 10 V ... 600 V AC, automatic range selection
- Measures current up to 1200 A
- Security / Standards: IEC1010CAT III 600V

Manufacturer: PCE Instruments

ISO-Certified Test Instruments Manufacturer

Custom-Made Test Instruments

PCE Instruments offers a wide range of stock products. However, despite an extensive selection of stock product offerings, sometimes a custom product is required to satisfy the specific requirements of a new, groundbreaking or special application.

Are you looking for custom test instruments?
Look no further than PCE Instruments. The DIN EN ISO 9001-certified PCE Product and Development Company GmbH produces customized test instruments tailored to meet the unique needs of a diverse customer base. By capitalizing on the expert knowledge and extensive experience of PCE’s industry-leading Tailored Test Instrumentsengineers and technicians to create custom-built test instruments, customers obtain measuring devices designed specifically for the task at hand.

Throughout the design, development and production process, PCE's engineers and technicians work hand-in-hand with each customer to ensure the final test instrument exceeds expectations. Specifications are clearly defined from the start of the project. Sensors, microprocessors and other electronic components are sourced from high-quality suppliers. Software is written to best support the customer's systems, processes and procedures. Qualified calibration laboratories are tasked with verifying the measurement accuracy of the custom test instrument, and rigorous testing is conducted to make certain that the device will function properly under the anticipated operating conditions.

If you are interested in pursuing the creation of a custom test instrument designed to accommodate an unusual or highly specialized measuring task, please contact the friendly and knowledgable staff at info@industrial-needs.com or +44 (0) 2380 987 035 for PCE Instruments UK, or at info@pce-americas.com or +1 (561) 320-9162 for PCE Americas Inc.