PCE Instruments: Test Instruments

Order no.: PCE-191 CB

PCE-191 CB is a handheld, portable wire tracer, cable detector or cable fault meter used for locating wires and cables hidden behind walls and insulation.


- Power range: 220 to 240 V AC
- Frequency range: 50 / 60 Hz
- Acoustic alarm

 

Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: PCE-CL 10

PCE-CL 10 is a cable locator that uses the conductive method to detect metal pipes or pipe tracer wires. With PCE-CL 10, you also can locate power cables, lines, circuits, short circuits and ground points, as well as test protective tubing and coaxial cables. To perform these functions, it is not necessary to disconnect the power. Location can be identified in floors, ceilings, walls and the ground, even behind concrete and brick.


- Operating temperature / humidity: 0 ... +40 ºC or
  +32 ... +104 ºF / max. 80% rh
- Storing temperature / humidity: -20 ... +60 ºC or
  -4 ... +140 ºF/ max. 80% rh
- Max. Voltage: 400 VAC (0 - 60 Hz) / 400 V DC

 

Manufacturer: PCE Instruments
Order no.: PCE-CL 20

PCE-CL 20 is a cable locator used to detect live and voltage-free electrical wires. This cable detector also can be used to locate metallic and non-metallic gas or water pipes, identify short circuits, and follow lines inside walls or under flooring.


- Output signal: 125 kHz
- Compatible with one- or two-pole circuits
- Automatic, manual and UAC measuring modes 

 

Manufacturer: PCE Instruments
Order no.: PCE-VE-N-ROL
Cable reel PCE-VE-N-ROL suitable for PCE-VE-N-SC10. Cable reel for holding the 10 m cable and the hand-held device of the PCE-VE 3xx N series.
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CA-C173

The 4-caliber Clamp Meter from the C1XX series for multimeters has a diameter of 52 mm (2.0 in), maximum 1000 A AC, and is designed for power and harmonics measurement. The 4-caliber Clamp Meter can be connected via 4 mm (0.2 in) safety plugs to a multimeter. It is also possible to connect the 4-caliber Clamp Meter via the 4 mm (0.2 mm) sockets or the BNC connector to a data acquisition system. The test instrument comes manufacturer calibrated. As all instruments, it can be certified to ISO as an option.
- Measuring range: 1 mA ... 1 A, 10 mA ... 10 A, 100 mA ... 100 A, 1 A ... 1000 A
- Transformer Ratio: 1 A / 1 V, 10 A / 1 V, 100 A / 1 V, 1000 A / 1 V
- Connection: 4 mm / 0.2 in male plugs
- Output: AC voltage

Manufacturer: Chauvin Arnoux GmbH
Order no.: CA-C173

The 4-caliber Clamp on Tester from the C1XX series for multimeters has a diameter of 52 mm (2.0 in), maximum 1000 A AC, and is designed for power and harmonics measurement. The 4-caliber Clamp on Tester can be connected via 4 mm (0.2 in) safety plugs to a multimeter. It is also possible to connect the 4-caliber Clamp on Tester via the 4 mm (0.2 mm) sockets or the BNC connector to a data acquisition system. The test instrument comes manufacturer calibrated. As all instruments, it can be certified to ISO as an option.
- Measuring range: 1 mA ... 1 A, 10 mA ... 10 A, 100 mA ... 100 A, 1 A ... 1000 A
- Transformer Ratio: 1 A / 1 V, 10 A / 1 V, 100 A / 1 V, 1000 A / 1 V
- Connection: 4 mm / 0.2 in male plugs
- Output: AC voltage

Manufacturer: Chauvin Arnoux GmbH
Order no.: CA-C173

The 4-caliber Current Clamp from the C1XX series for multimeters has a diameter of 52 mm (2.0 in), maximum 1000 A AC, and is designed for power and harmonics measurement. The 4-caliber Current Clamp can be connected via 4 mm (0.2 in) safety plugs to a multimeter. It is also possible to connect the 4-caliber Current Clamp via the 4 mm (0.2 mm) sockets or the BNC connector to a data acquisition system. The test instrument comes manufacturer calibrated. As all instruments, it can be certified to ISO as an option.
- Measuring range: 1 mA ... 1 A, 10 mA ... 10 A, 100 mA ... 100 A, 1 A ... 1000 A
- Transformer Ratio: 1 A / 1 V, 10 A / 1 V, 100 A / 1 V, 1000 A / 1 V
- Connection: 4 mm / 0.2 in male plugs
- Output: AC voltage

Manufacturer: Chauvin Arnoux GmbH
Order no.: PCE-BPHC 1
Calibration block for concrete tester PCE-BPHC 1

- Test anvil to verify readings of concrete test hammer
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CAL-PCE-MAVOLUX

Calibration Certificate CAL-PCE-MAVOLUX for Mavolux light meters.

N.B. Calibration certificates are excluded from the right of return as they are customer-specific.

Manufacturer: Gossen Foto- und Lichtmesstechnik GmbH
Test Instruments manufacturer
Order no.: CAL-PCE-789-A
• ISO calibration certificate for the PCE-789 calibrator, certifies the accuracy and is often required to comply with DIN ISO 9000. For all thermocouples.

N.B. Calibration certificates are issued specifically for the customer and are excluded from the right of return.
Manufacturer: Exova Metech GmbH ( Caldi )
Test Instruments manufacturer
Order no.: CAL-PCE-LES
For compliance with DIN ISO 9000 for the tachometer function.

N.B. Calibration certificates are issued specifically for the customer and are excluded from the right of return.
Manufacturer: PCE Instruments
Test Instruments manufacturer
Order no.: CAL-SH5-Z
[more]
Manufacturer: Exova Metech GmbH ( Caldi )
Test Instruments manufacturer
Order no.: CS 173

The temperature calibrator is used for calibration of contact temperature sensors and infrared meters. A reference sensor can be inserted into a separate bore of the temperature reference source. Due to the built-in PID regulator, with a thin platinum coating, and the use of a 2 point precision inspection (PAC-function), the temperature reference source achieves high precision and reliability. An optional purchasable calibration certificate, based on national standards, verifies the quality of the temperature reference source.


- Temperature range: + 30 °C ... + 200 °C
- Resolution: 0.1 °C
- Precision: ± 0.2 °C

 

Manufacturer: Dostmann electronic GmbH
Order no.: CS 174

The temperature calibrator is used for calibration of contact temperature sensors and infrared meters. A reference sensor can be inserted into a separate bore of the temperature reference source. Due to the built-in PID regulator, with a thin platinum coating, and the use of a 2 point precision inspection (PAC-function), the temperature reference source achieves high precision and reliability. An optional purchasable calibration certificate, based on national standards, verifies the quality of the temperature reference source.


- Temperature range: between -40 °C and + 85 °C
- Resolution: 0.1 °C
- Precision: ± 0.2 °C

 

Manufacturer: Dostmann electronic GmbH
Order no.: CS 175

The temperature calibrator is used for calibration of contact temperature sensors and infrared meters. A reference sensor can be inserted into a separate bore of the temperature reference source. Due to the built-in PID regulator, with a thin platinum coating, and the use of a 2 point precision inspection (PAC-function), the temperature reference source achieves high precision and reliability. An optional purchasable calibration certificate, based on national standards, verifies the quality of the temperature reference source.


- Temperature range: between -40 °C and + 85 °C
- Resolution: 0.01 °C
- Precision: ± 0.05 °C

 

Manufacturer: Dostmann electronic GmbH
Order no.: PCE-AT 5

The PCE-AT 5 car measuring device - handheld tachometer is a portable device used to measure revolutions per minute (rpm) in one-cylinder two-stroke and eight-cylinder four-stroke combustion engines with electric ignition starters. The PCE-AT 5 handheld automotive tachometer features an easy-to-read, backlit digital LCD display and flashlight functionality for low-light applications.


- Measurement range: 100 ... 20000 rpm
- Resolution: 1 rpm
- Accuracy: ± 10 rpm
- Measurement interval: 0.5 seconds

 

Manufacturer: PCE Instruments
Order no.: PCE-CT 27FN

PCE-CT 27FN is a Car Measuring Device that takes non-destructive measurements of nonmagnetic coating, insulating layer and dry film thickness (DFT) on metal substrates such as steel and aluminum. Ideal for surface testing, automotive paint inspection, material testing and manufacturing quality control applications.


- Measuring range of 0 ... 1250 µm / 0 ... 50 mils
- Accuracy of ±(2 % + 2 µm) / ±(2 % + 0.1 mils)
- Features a resolution of 0.1 µ / 0.1 mils 

 

Manufacturer: PCE Instruments
Order no.: PCE-CT 27FN-ICA

PCE-CT 27FN is a Car Measuring Device that takes non-destructive measurements of nonmagnetic coating, insulating layer and dry film thickness (DFT) on metal substrates such as steel and aluminum. Ideal for surface testing, automotive paint inspection, material testing and manufacturing quality control applications.


- Measuring range of 0 ... 1250 µm / 0 ... 50 mils
- Accuracy of ±(2 % + 2 µm) / ±(2 % + 0.1 mils)
- Features a resolution of 0.1 µ / 0.1 mils
- incl. ISO Calibration Certificate 

 

Calibration certificates are issued specifically for the customer and are excluded from the right of return.

Manufacturer: PCE Instruments
Order no.: PCE-LES 300
The Car Measuring Device PCE-LES 300 is equipped with 9 high-power LEDs that generate a light intensity of 5100 lux at 6000 FPM at a distance of 20 cm / 7.9 in. This allows the PCE-LES 300 handheld tachometer / stroboscope to provide a large and bright area of illumination.

- Flash frequency up to 120000 FPM
- Accuracy: ± 0.01%
- Adjustable deceleration time
- 9 high-power LEDs
- Phase shift
- Includes factory calibration certificate
Manufacturer: PCE Instruments
Order no.: GMK 210

The caravan moisture meter is the ideal tool to quickly locate moisture not only in buildings, but also on boats or in caravans. The measuring method of the moisture meter works absolutely non-destructively.


- Non-destructive test / measurement method
- Moisture displayed in per cent
- Acoustic / visual moisture assessment
- 10 mm / .4 in and 25 mm / 1 in measuring depth
- Resolution: 0.1 % (1%) and 1 % (above 19.9 %)
- IP65

 

Manufacturer: GHM Messtechnik GmbH
Test Instruments manufacturer

ISO-Certified Test Instruments Manufacturer

Custom-Made Test Instruments

PCE Instruments offers a wide range of stock products. However, despite an extensive selection of stock product offerings, sometimes a custom product is required to satisfy the specific requirements of a new, groundbreaking or special application.

Are you looking for custom test instruments?
Look no further than PCE Instruments. The DIN EN ISO 9001-certified PCE Product and Development Company GmbH produces customized test instruments tailored to meet the unique needs of a diverse customer base. By capitalizing on the expert knowledge and extensive experience of PCE’s industry-leading Tailored Test Instrumentsengineers and technicians to create custom-built test instruments, customers obtain measuring devices designed specifically for the task at hand.

Throughout the design, development and production process, PCE's engineers and technicians work hand-in-hand with each customer to ensure the final test instrument exceeds expectations. Specifications are clearly defined from the start of the project. Sensors, microprocessors and other electronic components are sourced from high-quality suppliers. Software is written to best support the customer's systems, processes and procedures. Qualified calibration laboratories are tasked with verifying the measurement accuracy of the custom test instrument, and rigorous testing is conducted to make certain that the device will function properly under the anticipated operating conditions.

If you are interested in pursuing the creation of a custom test instrument designed to accommodate an unusual or highly specialized measuring task, please contact the friendly and knowledgable staff at info@industrial-needs.com or +44 (0) 2380 987 035 for PCE Instruments UK, or at info@pce-americas.com or +1 (561) 320-9162 for PCE Americas Inc.