The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.
- Measuring range: 10 ... 999.9 V - AC voltage AC - Alternating current AC - Active power - Power factor - Phase angle - Frequency - Harmonic measurement - Data memory: 512 kB (non-volatile memory) - incl. 4 current clamps / tapping terminals - Standards: IP 30 / IEC 61 010, 600 V / CAT III - incl. ISO Calibration Certificate - incl. ISO Calibration Certificate
The easy-to-use PCE-PA 8300 Clamp-On Tester is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:
- Voltage measurement range of 10 V ... 600 V AC - Current measurement range of (Set 1) 20 A ... 1200 A AC - Performance measurement range of 0 kW ... 9.999 MW (VA/VAR) - Simultaneous display of harmonics and waveform - Graphic Phasor diagram - Captures transients including dip, swell, and outage
The easy-to-use PCE-PA 8300 Clamp-On Tester is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:
- Voltage measurement range of 10 V ... 600 V AC - Current measurement range of (Set 2) 30 A ... 3000 A AC - Performance measurement range of 0 kW ... 9.999 MW (VA/VAR) - Simultaneous display of harmonics and waveform - Graphic Phasor diagram - Captures transients including dip, swell, and outage
PCE-PCM 1 is a multipurpose clamp-on tester or power analyzer used to measure alternating current (AC), voltage (TRMS) and frequency to determine active (kW), apparent (kVA) and reactive (kVAR) power as well as active energy (kWh) consumption. Both the phase angle and the power factor (cos φ) are shown on the handheld power meter's large and easy-to-read backlit display.
- Voltage (50 ... 200 Hz): 100 / 400 / 750V, ± (1.2% + 5 digits) - Internal memory: Stores up to 99 measurement values - Includes USB cable and PC software - Three-phase power measurement - True RMS
With the clamp-on tester AC currents of up to 1000 A AC can be measured easily. At the same time, voltages of up to 1000V AC / DC can be measured with the clamp-on tester.
Measuring function
- Current measurement AC
- Inrush current AC
- Voltage measurement DC
- Voltage measurement AC
- Frequency measurement
- Frequency measurement current measurement function
- Frequency measurement voltage measurement function
- Duty cycle
- Resistance measurement
- Continuity test
- Capacity measurement
- Diode measurement
- Single-phase power measurement
- Power factor capacitive / inductive
- Harmonics measurement
PCE-TDS 100HSH-ICA is a portable handheld clamp-on Clamp-on Ultrasonic Flow Meter used for non-invasive, unobstructed and highly accurate measurements of the flow velocity of liquids in metal, plastic and rubber pipes and tubes with a diameter of 20 … 108 mm / approx. 3/4 in ... 4in. Software sold separately - see accessories for details.
PCE-TDS 100H-ICA is a portable handheld clamp-on Clamp-on Ultrasonic Flow Meter used for non-invasive, unobstructed and highly accurate measurements of the flow velocity of liquids in metal, plastic and rubber pipes and tubes with a diameter of 57 … 720 mm / approx. 2 ... 28 in. Software sold separately - see accessories for details.
The Clamp-on Ultrasonic Flow Meter is required as part of a control measurement or to quickly determine the flow in a pipeline and is a portable / easy-to-install measuring system. The Clamp-on Ultrasonic Flow Meter works according to the transit time difference method. The measuring principle of the flow meter is quite simple.
- Measuring range: -32 ... 32 m/s, -105 ... 105 ft/s - Resolution: 0.0001 m/s, 0.00033 ft/s - Pipe sizes: 50 … 720 mm (approx. 1.9 … 28") 20 …108 mm (approx. 0.8 … 4.2") - Sensor temperature range: 0 ... 160°C / 32 ... 320°F - Sensor installation: V, Z - Incl. sensors TDS-HM and TDS-HS on rails - Incl. ISO Calibration Certificate
PCE-TDS 100HS-ICA is a portable handheld clamp-on Clamp-on Ultrasonic Flow Meter used for non-invasive, unobstructed and highly accurate measurements of the flow velocity of liquids in metal, plastic and rubber pipes and tubes with a diameter of 20 … 108 mm / approx. 3/4 in ... 4in. Software sold separately - see accessories for details.
The Clamp-on Ultrasonic Flow Meter has a measuring range of ±32 m/s. To perform flow measurement with the Clamp-on Ultrasonic Flow Meter, the flow velocity, the volume flow and the volume are displayed after entering the pipe and medium specifications.
- Measuring range: ±32 m/s
- Resolution: 0.001 m/s
- Sensor for pipe diameter DN 300 ... 6000 mm
- Sensor dimensions: 91 x 52 x 44 mm
- for different media
- for different pipe materials
- measuring parameters: flow velocity, flow rate and volume
- Interface: USB
- Data logger: 32 GB memory capacity (10 million measuring points)
- LiPo battery - incl. ISO Calibration Certifikcate
The Clamp-on Ultrasonic Flow Meter has a measuring range of ±32 m/s. To perform flow measurement with the Clamp-on Ultrasonic Flow Meter, the flow velocity, the volume flow and the volume are displayed after entering the pipe and medium specifications.
- Measuring range: ±32 m/s
- Resolution: 0.001 m/s
- Sensor for pipe diameters DN 50 ... 700 / 57 ... 720 mm
- Temperature resistance: -30 ... 160 °C
- for different media
- for different pipe materials
- Measuring parameters: Flow velocity, flow rate and volume
- Interface: USB
- Data logger: 32 GB memory capacity (10 million measuring points)
The Clamp-on Ultrasonic Flow Meter has a measuring range of ±32 m/s. To perform flow measurement with the the Clamp-on Ultrasonic Flow Meter, the flow velocity, the volume flow and the volume are displayed after entering the pipe and medium specifications.
- Measuring range: ±32 m/s
- Resolution: 0,001 m/s
- incl. sensor set
- Sensor for pipe diameters DN 50 ... 700 / 57 ... 720 mm, DN 300 ... 6000
- Temperature resistance: -30 ... 160 °C
- for different media
- for different pipe materials
- Measuring parameters: Flow velocity, volume flow and volume
- Interface: USB
- Data logger: 32 GB memory capacity (10 million measuring points)
The Clamp-on Ultrasonic Flow Meter has a measuring range of ±32 m/s. To perform flow measurement with the Clamp-on Ultrasonic Flow Meter, the flow velocity, the volume flow and the volume are displayed after entering the pipe and medium specifications.
- Measuring range: ±32 m/s
- Resolution: 0,001 m/s
- incl. sensor set
- Sensor for pipe diameters DN 50 ... 700 / 57 ... 720 mm
- Temperature resistance: -30 ... 160 °C
- for different media
- for different pipe materials
- Measuring parameters: Flow velocity, flow rate and volume
- Interface: USB
- Data logger: 32 GB memory capacity (10 million measuring points)
The Clamp-on Ultrasonic Flow Meter has a measuring range of ±32 m/s. To perform flow measurement with the Clamp-on Ultrasonic Flow Meter, the flow velocity, the volume flow and the volume are displayed after entering the pipe and medium specifications.
- Measuring range: ±32 m/s
- Resolution: 0.001 m/s
- Sensor for pipe diameter: DN 15 ... 100 / 20 ... 108 mm
- Sensor dimensions: 45 x 30 x 30 mm
- Temperature resistance from -30 ... 160 °C
- for different media
- for different pipe materials
- Measuring parameters: flow velocity, volume flow and volume
- Interface: USB
- Data logger: 32 GB memory capacity (10 million measuring points)
The Clamp-on Ultrasonic Flow Meter has a measuring range of ±32 m/s. To perform flow measurement with the Clamp-on Ultrasonic Flow Meter, the flow velocity, the volume flow and the volume are displayed after entering the pipe and medium specifications.
- Measuring range: ±32 m/s
- Resolution: 0.001 m/s
- incl. 4 sensors
- Sensor for pipe diameters: DN 15 ... 100 / 20 ... 108 mm, DN 300 ... 6000 mm
- for different media
- for different pipe materials
- measuring parameters: Flow velocity, volume flow and volume
- Interface: USB
- Data logger: 32 GB memory capacity (10 million measuring points)
The Clamp-on Ultrasonic Flow Meter has a measuring range of ±32 m/s. To perform flow measurement with the Clamp-on Ultrasonic Flow Meter, the flow velocity, the volume flow and the volume are displayed after entering the pipe and medium specifications.
- Measuring range: ±32 m/s
- Resolution: 0.001 m/s
- incl. 4 sensors
- Sensor for pipe diameters DN 50 ... 700 / 57 ... 720 mm, DN 15 ... 100 / 20 ... 108 mm
- Temperature resistance: -30 ... 160 °C
- for different media
- for different pipe materials
- Measuring parameters: Flow velocity, volume flow and volume
- Interface: USB
- Data logger: 32 GB memory capacity (10 million measuring points)
The Clamp-on Ultrasonic Flow Meter has a measuring range of ±32 m/s. To perform flow measurement with the Clamp-on Ultrasonic Flow Meter, the flow velocity, the volume flow and the volume are displayed after entering the pipe and medium specifications.
- Measuring range: ±32 m/s
- Resolution: 0.001 m/s
- incl. 4 sensors
- Sensor for pipe diameters DN 20-108 mm / 50-700 mm / 315-6000 mm
- Temperature resistance: -30 ... 160 °C
- for different media
- for different pipe materials
- Measuring parameters: Flow velocity, volume flow and volume
- Interface: USB
- Data logger: 32 GB memory capacity (10 million measuring points)
The Clamp-on Ultrasonic Flow Meter has a measuring range of ±32 m/s. To perform flow measurement with the Clamp-on Ultrasonic Flow Meter, the flow velocity, the volume flow and the volume are displayed after entering the pipe and medium specifications.
- Measuring range: ±32 m/s
- Resolution: 0.001 m/s
- Sensor for pipe diameters: DN 15 ... 100 / 20 ... 108 mm
- for different media
- for different pipe materials
- Measuring parameters: Flow velocity, volume flow and volume
- Interface: USB
- Data logger: 32 GB memory capacity (10 million measuring points)
PCE Instruments offers a wide range of stock products. However, despite an extensive selection of stock product offerings, sometimes a custom product is required to satisfy the specific requirements of a new, groundbreaking or special application.
Are you looking for custom test instruments?
Look no further than PCE Instruments. The DIN EN ISO 9001-certified PCE Product and Development Company GmbH produces customized test instruments tailored to meet the unique needs of a diverse customer base. By capitalizing on the expert knowledge and extensive experience of PCE’s industry-leading engineers and technicians to create custom-built test instruments, customers obtain measuring devices designed specifically for the task at hand.
Throughout the design, development and production process, PCE's engineers and technicians work hand-in-hand with each customer to ensure the final test instrument exceeds expectations. Specifications are clearly defined from the start of the project. Sensors, microprocessors and other electronic components are sourced from high-quality suppliers. Software is written to best support the customer's systems, processes and procedures. Qualified calibration laboratories are tasked with verifying the measurement accuracy of the custom test instrument, and rigorous testing is conducted to make certain that the device will function properly under the anticipated operating conditions.
If you are interested in pursuing the creation of a custom test instrument designed to accommodate an unusual or highly specialized measuring task, please contact the friendly and knowledgable staff at info@industrial-needs.com or +44 (0) 161-464902-5 for PCE Instruments UK, or at info@pce-americas.com or +1 (561) 320-9162 for PCE Americas Inc.
engineers and technicians to create custom-built test instruments, customers obtain measuring devices designed specifically for the task at hand.
