Three-Phase Power Meter PCE-830-1
£ 2,127.00
Price excl. VAT &. delivery
2 year Warranty

The 3-Phase-Power Meter / 3-Phase Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase-Power Meter / 3-Phase Power Analyzer also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

 

Three-Phase Power Analyzer PCE-PA 8300-1
£ 2,661.00
Price excl. VAT &. delivery
2 year Warranty

The easy-to-use 3-Phase Power Meter / 3-Phase Power Analyzer is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. This is a 3-phase power analyzer that features:


- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 1) 20 A ... 1200 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

Material Tester PCE-HT-450
£ 1,320.00
Price excl. VAT &. delivery
2 year Warranty
The material tester is an analog measuring device to determine concrete strength. The measuring method of the material tester is based on the Schmidt principle. With this measuring method, a kinetic impact energy hits the concrete from the material tester. The resulting rebound enables the material tester to determine the strength of the concrete.

- Nominal kinetic energy: 4.5 J
- For high-strength concrete
- Simple and quick operation
- For determining concrete hardness
- Schmidt principle
Three-Phase Power Analyzer PCE-830-1-ICA incl. ISO Calibration Certificate
£ 2,554.00
Price excl. VAT &. delivery
2 year Warranty
ISO Calibration

The PCE-830 3-Phase Power Meter / 3-Phase Power Analyzer is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Power Meter / 3-Phase Power Analyzer also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate

Single-Phase / 1-Phase Power Meter PCE-360
£ 1,491.00
Price excl. VAT &. delivery
2 year Warranty

The PCE-360 is a Single-Phase Power Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.


- Measuring range: 10 ... 999.9 V
- AC voltage AC
- Alternating current AC
- Active power
- Power factor
- Phase angle
- Frequency
- Harmonic measurement
- Data memory: 512 kB 
  (non-volatile memory)
- incl. 4 current clamps / tapping terminals
- Standards: IP 30 / IEC 61 010, 600 V / CAT III
incl. ISO Calibration Certificate 

Roll Hardness Tester PCE-HT-450
£ 1,320.00
Price excl. VAT &. delivery
2 year Warranty
The roll hardness tester is an analog measuring device to determine concrete strength. The measuring method of the roll hardness tester is based on the Schmidt principle. With this measuring method, a kinetic impact energy hits the concrete from the roll hardness tester. The resulting rebound enables the roll hardness tester to determine the strength of the concrete.

- Nominal kinetic energy: 4.5 J
- For high-strength concrete
- Simple and quick operation
- For determining concrete hardness
- Schmidt principle
Single Phase / 1-Phase Power Meter PCE-360-ICA incl. ISO Calibration Certificate
£ 1,753.00
Price excl. VAT &. delivery
2 year Warranty
ISO Calibration

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.


- Measuring range: 10 ... 999.9 V
- AC voltage AC
- Alternating current AC
- Active power
- Power factor
- Phase angle
- Frequency
- Harmonic measurement
- Data memory: 512 kB 
  (non-volatile memory)
- incl. 4 current clamps / tapping terminals
- Standards: IP 30 / IEC 61 010, 600 V / CAT III
incl. ISO Calibration Certificate 
incl. ISO Calibration Certificate 

Concrete Hardness Tester PCE-HT-450
£ 1,320.00
Price excl. VAT &. delivery
2 year Warranty
The concrete hardness tester is an analog measuring device to determine concrete strength. The measuring method of the concrete hardness tester is based on the Schmidt principle. With this measuring method, a kinetic impact energy hits the concrete from the concrete hardness tester. The resulting rebound enables the concrete hardness tester to determine the strength of the concrete.

- Nominal kinetic energy: 4.5 J
- For high-strength concrete
- Simple and quick operation
- For determining concrete hardness
- Schmidt principle
Clamp on Tester PCE-830-1
£ 2,127.00
Price excl. VAT &. delivery
2 year Warranty

The PCE-830 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp on Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

NDT Tester - Hardness Tester PCE-HT-450
£ 1,320.00
Price excl. VAT &. delivery
2 year Warranty
The NDT tester - hardness tester is an analog measuring device to determine concrete strength. The measuring method of the NDT tester - hardness tester is based on the Schmidt principle. With this measuring method, a kinetic impact energy hits the concrete from the NDT tester - hardness tester. The resulting rebound enables the NDT tester - hardness tester to determine the strength of the concrete.

- Nominal kinetic energy: 4.5 J
- For high-strength concrete
- Simple and quick operation
- For determining concrete hardness
- Schmidt principle
Electrical Tester PCE-830-1
£ 2,127.00
Price excl. VAT &. delivery
2 year Warranty

The PCE-830 Electrical Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Electrical Tester also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm / 1.1 in diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 mm x 62 mm x 36 mm / 8.2 in x 2.4 in x 1.4 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)

Electrical Tester PCE-830-1-ICA incl. ISO Calibration Certificate
£ 2,554.00
Price excl. VAT &. delivery
2 year Warranty
ISO Calibration

The Electrical Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Electrical Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate

Three Phase Power Data Logger PCE-PA 8300-1
£ 2,661.00
Price excl. VAT &. delivery
2 year Warranty

The easy-to-use PCE-PA 8300 Three Phase Power Data Logger is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:


- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 1) 20 A ... 1200 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

Clamp on Tester PCE-830-1-ICA incl. ISO Calibration Certificate
£ 2,554.00
Price excl. VAT &. delivery
2 year Warranty
ISO Calibration

The PCE-830 Clamp on Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Clamp on Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate

Electrical Tester PCE-PA 8300-1
£ 2,661.00
Price excl. VAT &. delivery
2 year Warranty

The easy-to-use PCE-PA 8300 Electrical Tester is the ideal tool for performing power and harmonics analysis as well as for measuring network capacity. The PCE-PA 8300 is a 3-phase power analyzer that features:


- Voltage measurement range of 10 V ... 600 V AC
- Current measurement range of (Set 1) 20 A ... 1200 A AC
- Performance measurement range of 0 kW ... 9.999 MW (VA/VAR)
- Simultaneous display of harmonics and waveform
- Graphic Phasor diagram
- Captures transients including dip, swell, and outage

1-Phase-Power Meter PCE-GPA 62
£ 845.00
Price excl. VAT &. delivery
2 year Warranty

The 1-Phase-Power Meter PCE-GPA 62 (Graphic Power Quality Analyzer) with network analyzer / power and energy meter with data logger. The one-phase harmonic Analyzer (Graphic Power Quality Analyzer) is used for single-phase or three-phase measurements of active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics. This clamp meter is a perfect tool for all energetic measurements. It is delivered manufacturer calibrated and can be certified to ISO or standards.

- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Records up to 50,000 records


HVACR Tester PCE-830-1-ICA incl. ISO Calibration Certificate
£ 2,554.00
Price excl. VAT &. delivery
2 year Warranty
ISO Calibration

The HVACR Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase HVACR Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.


- PCE-830 + PCE-6801 amp clamp (100 A)
- Electrical conductor pick-up: 30 mm diameter
- Range selection: manual (1 A, 10 A, 100 A)
- Clamp dimensions: 210 x 62 x 36 mm
- Incl. ISO calibration certificate

1-Phase-Power Meter PCE-GPA 62-ICA incl. ISO Calibration Certificate
£ 958.00
Price excl. VAT &. delivery
2 year Warranty
ISO Calibration

This 1-Phase-Power Meter is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyzer clamp is equipped with data logger. The test instrument is delivered manufacturer ISO calibrated.


- Real-time test, register and measurement of voltage and current (real and effective) 
- Measures power factor and phase angle, frequency, energy, active, reactive and apparent power 
  (single-phase or three-phase in symmetrical networks). 
- Max. conductor diameter: 55 mm / 2.2 in
- Records up to 50,000 records
incl. ISO Calibration Certificate