2 year Warranty
The torque wrench tester of the PCE-TWM series can test torque wrenches up to 500 Nm / 368.78 ft-lb, depending on the sensor. Due to the precise evaluation electronics, the torque wrench tester has a measurement accuracy of 0.5 % of the measurement range. The torque wrench is fixed by means of a 1/4' female square. The torque wrench tester consists of an evaluation unit and an external torque transducer with a cable which makes the measurement setup convenient.
- Measurement range: 500 Nm (50 kgfm) / 368.78 ft-lb
- Resolution: 1 Nm / 0.738 ft-lb
- Accuracy: ±0.5 % of measurement range
- Units of measurement: Nm, Ncm, kgfm, lbfin, gfm
- Calibration: possible with external F2 weights
- Max. overload: 50 % of measurement range
The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.
- Measuring range: 2 Nm (0,2 kgf-m) / 1.475 ft-lb
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm
The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.
- Measuring range: 10 Nm (1 kgf-m) / 7.38 ft-lb
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm
The torque meter serves for detection of the loosening torque as well as for tightening of screws. Simultaneously the torque meter can be used as a monitoring instrument. The torque test instrument provides a keyed chuck with two steady handles.
- Measuring range: 5 Nm (0,5 kgf-m) / 3.69 ft-lb
- Max. 0,5 % accuracy from the measuring range
- Measuring rate freely adjustable up to 1000 Hz
- 24 Bit Processor
- Keyed chuck up to Ø 13 mm
The Torque Meter PCE-TM 80 with external sensor to measure the static or startup torque moment in screws, components, switches, transmission shafts, etc. The Torque Meter PCE-TM 80 is an affordable solution to easily calibrate and test static torque measurements.
- Range 0 ... 147 Ncm / 0 ... 13.01 lbfin
- Selection of 3 units (Ncm, kgfcm, lbfin)
- Digital output RS-232
- External torque sensor
- Measures startup or static torque, not dynamic torque
The PCE-830-2 Clamp Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This Clamp Meter also measures parameters such as voltage, current, frequency, harmonics, and power as well as indicating, according to standard EN50160, harmonic values, interharmonics, and asymmetrics. Interference, such as interruptions, leaks, overloads, or transience (from 16 µs) are detected with their corresponding values. The power logging instrument is delivered manufacturer calibrated. An ISO calibration certificate may be ordered optionally.
- PCE-830 + PCE-6802 amp clamp (1000 A)
- Electrical conductor pick-up: 55 mm / 2.1 in diameter
- Range selection: manual (10 A, 100 A, 1000 A)
- Clamp dimensions: 244 mm x 97 mm x 46 mm / 9.6 in x 3.7 in x 1.8 in
- Sampling rate: 2 sec.
- Memory size: 512 kB (max. 52,000 values (single phase)