Power Meter

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

• Measuring range: 10 … 999.9 V
• AC voltage AC
• Alternating current AC
• Active power
• Power factor
• Phase angle
• Frequency
• Harmonic measurement
• Data memory: 512 kB   (non-volatile memory)
• incl. 4 current clamps / tapping terminals
• Standards: IP 30 / IEC 61 010, 600 V / CAT III
• incl. ISO Calibration Certificate
• incl. ISO Calibration Certificate

The PCE-830 Power Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Power Meter also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 x 62 x 36 mm
• Incl. ISO calibration certificate

The PCE-830-3 Power Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This Power Meter also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-3007 flexible amp clamp (3000A)
• Electrical conductor pick-up: 170 mm / 6.7 in diameter
• Minimum radial curve: 35 mm / 1.4 in
• Length of electrical conductor: 610 mm / 24 in
• Sampling rate: 2 sec.
• Memory size: 512 kB / max. 52,420 data (1 phase)
• Incl. ISO calibration certificate

The PCE-830 Power Meter is used for measuring one to three phases of electrical quantities for alternating current (AC). This Power Meter also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-6802 amp clamp (1000 A)
• Electrical conductor pick-up: 55 mm / 2.2 in diameter
• Range selection: manual (10 A, 100 A, 1000 A)
• Clamp dimensions: 244 x 97 x 46 mm / 9.6 x 3.8 x 1.8 in
• Incl. ISO calibration certificate

The Easycount-1-CEE-U energy meter is an electricity meter for alternating voltages up to 230 V, enclosed in a splash-proof and impact-resistant housing. The cable ends of the Easycount-1-CEE-U energy meter are equipped with male and female connectors.

• Uncalibrated counter
• Voltage input: 230 VAC
• Current rating: 16 A
• Frequency: 50 HZ

The Easycount-1-Schuko-U energy meter is an electricity meter for alternating voltages up to 230 V, enclosed in a splash-proof and impact-resistant housing. The cable ends of the Easycount-1-Schuko-U energy meter are equipped with male and female connectors.

• Uncalibrated counter
• Voltage input: 230 VAC
• Current rating: 16 A
• Frequency: 50 HZ

The Easycount-1-CEE-G energy meter is an electricity meter for alternating voltages up to 230 V, enclosed in a splash-proof and impact-resistant housing. The cable ends of the Easycount-1-CEE-G energy meter are equipped with male and female connectors.

• Calibrated counter
• Voltage input: 230 VAC
• Current rating: 16 A
• Frequency: 50 HZ