Laboratory Technology

The gloss meter PCE-IGM 60 is an optical measuring instrument with a measuring geometry of 60 °. The surface is analyzed by the gloss meter and then the result is shown. Every surface has the characteristic to reflect light.

- Measurement geometry: 60° degree angle
- Measuring range: 0 ... 300 GU
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

The PCE-SGM 60 gloss meter with small measuring area is used on many types of surfaces to quantify their gloss units. This gloss-measuring device operates on the reflection principle by sending light from a calibrated light source onto the surface to be tested and then calculates the gloss level of the surface according to the reflection of light particles. This gloss meter allows you to measure very high gloss surfaces above 70 gloss units (GU).

- Measurement geometry: 60° degree angle
- Measurement up to 1000 gloss units
- Internal reading memory up to 5000 readings
- 3.5" TFT display
- Light source: D65
- Wave length: 400-700 nm
- Incl. ISO calibration certificate

The PCE-PGM 100 gloss meter works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the gloss meter emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.

- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU

 

The paint test equipment was developed for quality control and offers a very high accuracy. When using the paint test equipment, you can choose between different color spaces (CIE L*a*b*C*h, CIE L*a*b* and CIE XYZ). After a measurement with the paint test equipment the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the 100 reference values easily. 6 mm aperture for sample scanning.

- CIE L*a*b*C*h, L*a*b* and XYZ
- Automatic white and black calibration
- 8°/d geometry diffused illumination integrating sphere system
- Rechargable Li-ion battery

 

- Number of stirring points 5
- Max. Stirring quantity: 2000 ml
- Adjustable up to 1500 rpm
- Maximum 120°C / 248°F

The Handheld Roughness Tester is used to determine surface roughness. The compact surface roughness tester is a handheld device for mobile use. Due to the power supply via a powerful battery, it can be used directly on site. The handheld roughness tester is used in the laboratory, in production and everywhere where the roughness of surfaces is to be determined.

  

- Measures Ra, Rz, Rq and Rt in Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.005 ... 16.00 μm / 0.197µinch... 629.921 µinch measurement range
- Rz, Rt: 0.002 ... 200.0 μm / 0.079µinch... 7874.016 µinch measurement range
- Induction method with Diamond sensor

 

- Measuring range: 0 ... 1250 µm
- Accuracy: ± (1% + 1 µm)
- Resolution: 0.1 µm (<99.9 µm), 1 µm (> 100 µm)
- Measurement data storage for up to 500 data
- Data transfer via wifi and USB
- Two different probes for NFe and Fe (included)

The Roughness Tester PCE-RT 10-ICA is a small, light device with simple navigation. Despite the fact that the device functions on a very complex and elaborate level, the measurement results can be acquired quickly and in an accurate way. Very simple to operate with a motorized diamond sensor.

- Measures Ra in Metric (µm) and Imperial (µinch)
- Ra 0.05 to 10um / 2 µinch ... 400 µinch measurement range
- Rz 0.1 to 50um / 3.93 µinch ... 1968.50 µinch measurement range
- Induction method with Diamond sensor
- Accuracy < ± 10% and Repeatability < 6%
- With threshold function
- Uses 4 AA Batteries (Included)
- Incl. ISO calibration certificate

The PCE-PGM 100 gloss meter works with measuring geometries of 20°, 60° and 85°, using the reflection principle. This means that the gloss meter emits light which hits the surface to be tested. A part of the light will be absorbed by the surface and another part will be reflected.

- Measurement geometry: 20° / 60° / 85°
- Standards: ISO 2813 / GB/T 9754 / ASTM D 523 / ASTM D 2457
- Range: 20°: 0 ... 1000 GU / 60°: 0 ... 1000 GU / 85°: 0 ... 160 GU
- Incl. ISO calibration certificate

A very precise paint testing equipment with 45°/0° viewing angle. This very professional instrument works in color spaces CIEL*a*b*C*h*, CIEL*a*b*, and CIEXYZ. This kind of paint testing equipment is mainly made for the use in an R&D laboratory, for industrial product evaluation or for any kind of color testing application. The paint testing equipment comes fully equipped (click on detail sheet) and is manufacturer calibrated. - A paint testing equipment for industrial professionals and researchers -

- Measuring aperture of 8 mm and 45°/0° illumination/viewing angle
- Rechargeable lithium-ion battery
- Auto white black calibration
- Designed specifically for the food industry
- Software Included
- Stores 100 reference values and 20,000 samples

 

The Roughness Tester PCE-RT 11-ICA is a portable measuring instrument for determination of surface roughness according to Ra, Rz, Rq and Rt in just one device. The small roughness tester is especially designed for fast measuring of roughness.

- Measures Ra, Rz, Rq and Rt in both Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.05 µm … 10 µm / 0.002 µinch … 394 µinch measurement range
- Rz, Rt: 0.1 µm … 50 µm / 0.004 µinch …1968 µinch measurement range
- Robust Piezoelectric sensor
- Accuracy: ± 15% and Repeatability < 12%
- Built-in rechargeable li-ion battery
- Inc. ISO Calibration Certificate

- Measuring range: 0 ... 1250 µm
- Accuracy: ± (1% + 1 µm)
- Resolution: 0.1 µm (<99.9 µm), 1 µm (> 100 µm)
- Measurement data storage for up to 500 data
- Data transfer via Wifi and USB
- Two different probes for NFe and Fe (included)
- incl. ISO Calibration Certificate

The paint testing equipment is used to measure the brightness level of paper, cardboard, cellulose, pulp, textiles, paint, enamel, plastic, porcelain, cement, concrete, building materials, chemicals, powders, talc, starch, flour, salt, detergents, cosmetics and other non-metal substances.

- Measures the whiteness degree of blue light (Wb = R457)
- Meets ISO 2470 and ISO 3688 standards
- Compact, lightweight and user-friendly
- Resolution: 0.1
- Repeat accuracy : ±0.1

The paint test equipment was developed for quality control and offers a high accuracy. When using the paint test equipment, you can choose between different color spaces (CIE L*a*b*C*h, CIE L*a*b*). After a measurement with the paint test equipment, the reading can be used as a reference value while other readings can be recorded as a sample and later be compared to the reference value easily.

- CIE L*a*b*C*h, CIE L*a*b*
- Measuring geometry 8°/d
- White calibration standard included
- Stores 100 reference values and 20,000 samples
- Measuring aperture is 8 mm
- optional liquid sample kit listed under accessories

 

The simple design and an absolutely straightforward operation make it possible for the practitioner to use the adhesion tester as an instrument for daily adhesion tests. Using adhesive with rapid curing, the tests can be performed by the user in the shortest possible time.

- Breakout force: 200 kg
- Diameter of base dolly, mm: 15.1 (№ 1) and 19.5 (№ 2)
- Specific breakout force, MPa: Dolly №1 up to 10 MPa (100) Dolly
  №2 up to 6 MPa (60)

 

A color matching cabinet is used wherever products must have the same color properties during production. A color matching cabinet contributes to quality control. The color matching cabinet is a simulation instrument which is capable of displaying certain situations in order to analyze color characteristics of individual samples by means of different light types.

- Color assessment under different light types
- With hour counter
- Short warm-up time
- According to ASTM D1729, ISO3664, DIN, ANSI, BSI

This paint testing song is especially designed for meat, food, vegetables or wet products testing. Only the aperture comes into contact with the surfaces to be measured. So it is guaranteed that no liquids can cause cross contamination while doing the measurement. The paint testing equipment simulates to see surfaces like with human eyes. Used mainly in the medical and food industry the color test instrument in addition meets all requirements for plastics surface measurements (PP, PE, PET, ABS, EVA) and also powders. The paint testing equipment is delivered manufacturer calibrated, but can optionally be certified to ISO standards.

- Measuring aperture of 20 mm and 45°/0° illumination/viewing angle
- Rechargeable lithium-ion battery
- Auto white black calibration
- Designed specifically for the food industry
- Software included

 

The Bluetooth handheld surface - roughness tester is used to determine surface roughness. The compact roughness tester is a handheld device for mobile use. Due to the power supply via a powerful battery, it can be used directly on site. The roughness tester is used in the laboratory, in production and everywhere where the roughness of surfaces is to be determined.

- Measures Ra, Rz, Rq and Rt in Metric (µm) and Imperial (µinch)
- Ra, Rq: 0.005 ... 16.00 μm / 0.197 µinch... 629.921 µinch measurement range
- Rz, Rt: 0.002 ... 200.0 μm / 0.079 µinch... 7874.016 µinch measurement range
- Induction method with Diamond sensor
- Large OLED display
- Display for the position of the probe
- Micro-USB interface
- Bluetooth
- Download the app for free from the Google Play Store

The roughness tester PCE-RT 2000 is used for accurate measurement of surface roughness. The roughness tester can be used on all surfaces. The roughness is measured precisely with the roughness measuring device via the piezo probe.

- Measuring ranges Ra, Rq, Rc: 0.005 µm ... 16 µm / 0.197 µinch ... 629.9 µinch
- Measurement accuracy: <± 10%
- Micro USB interface
- 3 different cut-off wavelengths
- PC software