Order no.: PCE-DPD-F2

Force and Weight Indicator PCE-DPD-F2


£ 297.00
£ 356.40
:
4250348719591
PCE-DPD-F2
price ex. (VAT / delivery)
Delivery time: 10 - 14 days

Description

Force and Weight Indicator PCE-DPD-F2
Mounting display for strain gauges with mV & V / Modular output cards / 6 digit LED display / 230V or 24V power supply

The built-in display is used to indicate the force and weight detected by force sensors and load cells with strain gauges. The output signal of the measuring cell is irrelevant because the force and weight indicator makes it possible to display the correct weight in mV / V based on the set sensitivity. The force and weight indicator shows the measured values ​​on a 6-digit LED display. The measuring range could theoretically be between -199999 ... 999999. Depending on the desired and adjusted scaling, a corresponding unit sticker can be applied to the installation indicator. 

The force and weight indicator can directly supply voltage to the connected measuring cell with strain gauges. The supply voltage can be selected between 5V and 10V. Depending on the voltage selected, up to 8 or 4 force or load cells can be connected to the force and weight indicator. A special feature of this digital display for mV / V is the modular output concept. Different, changeable output cards are available depending on the application.

Highlights

- Digital display for strain gauges
- mV / V input
- 3 different measuring speeds
- Modular output cards available
- 1/8 DIN panel mounting dimensions
- LED display

Specification

Technical specification for DMS display of the PCE-DPD-F2

Signal Input Range 

Accuracy at 25°C

Sensitivity in
mV / V at 5V

Sensitivity in 
mV / V at 10V

0 ... 100 mV DC

± 0.05% of reading

20 mV / V 

10 mV / V

0 ... 30 mV DC

± 0.05% of reading

6 mV / V

3 mV / V

0 ... 20 mV DC

± 0.05% of reading

4 mV / V

2 mV / V

0 ... 15 mV DC

± 0.05% of reading

3 mV / V

1.5 mV / V

0 ... 10 mV DC

± 0.05% of reading

2 mV / V

1 mV / V

0 ... 5 mV DC

± 0.05% of reading

1 mV / V

0.5 mV / V

Maximum input voltage

30V in all measuring ranges

Supply voltage measuring cells

5V or 10V

Maximum current

140-mA

Maximum number of measuring cells
(with 350 Ohm measuring cells otherwise max. 140-mA)

5V supply: 1 ... 8 measuring cells
10V supply: 1 ... 4 measuring cells

Display

6-digit 7-segment LED display

Units (available by user)

g, kg, t, pcs, mg, lb, N, kN

Colour

Red

Character height

14 mm

Display area

-199999 ... 999999

Decimal 

Adjustable after each displayed digit

Under and Over Range display

The display flashes

Measuring rate (adjustable) / response time

16 Hz / 63 ms
50 Hz / 20 ms
60 Hz / 17 ms

Refresh rate display

16 Hz

Electrical connections

Screw connections
1 ... 2.5 mm²

Power supply

11 ... 60V DC / 24/48V AC

Input

Max. 1 W without output cards
Max. 4 W with output cards

Degree of protection

Front: IP65

Assembly

Panel cut

Size panel cutout

92 x 44 mm / 3.6 x 1.7 in 

Dimensions

96 x 48 x 91 mm / 3.7 x 1.9 x 3.6 in

Weight

About 150 g / < 1 lb

Operating temperature

0 ... 50°C / 32 ... 122°F

Storage temperature

-20 ... 70°C / -4 ... 158°F

Heating time

About 15 minutes



Delivery Scope

1 x Force and Weight Indicator PCE-DPD-F2
1 x Power supply terminal
1 x Strain gauge terminal
1 x Unit label
1 x User manual